Ford - Focus :: 2000 - Grinding / Popping Noise When Driving - Stops When Touch The Brakes
Feb 22, 2013
My car makes a grinding/popping noise when driving that worsens when I go over bumps and that completely stops if I even touch the brakes. When I accelerate, the noise speeds up as well. I took it to a mechanic about three months ago and he said it was a loose bumper and that he secured it. After leaving, the noise got louder and happened more often. Sometimes the noise doesn't happen, while other times it does. My dad changed my front brake pads about a month ago so it can't be those. Is it possible that it is still my bumper making the noise? If so, I don't understand why it would stop when I brake.
View 1 Replies
Advertisement
I have a 2000 Ford Focus with about 145,000 miles on it. When I'm driving I can hear a drumming noise. The faster I go the louder and more fast paced the drumming noise becomes. When I hit about 50 I can hear it, and the faster I go the louder it is. At about 60 the car starts to shake a little bit. When I'm going like 20 or 30 or so, it sounds like I can almost hear my tires turning if that makes sense. The noise is really loud and is starting to concern me. A friend said my CV boots are ripped, but before I take it into a mechanic I would like some non biased opinions.
View 5 Replies
2000 Excursion V10 4x4. I'm getting a popping noise coming from the rear end when I apply the brakes and come to a complete stop and when I release the brakes to take off. It only happens the moment it comes to a complete stop and the moment it takes off. Not when I'm putting it in forward or reverse or accelerating or decelerating. U joints are fine. I was laying under the truck poking around the other day and when I roll it back and forth in park the few inches it'll go, when it comes to the end of it's travel the axle wraps a little and it seems like the transfer case output shaft flange is moving in and out of the transfer case and causing the noise. I'm assuming there is a snap ring holding the output bearing in place. I didn't have time to drop the driveshaft but am planning on it this weekend to see if it still does it when I roll it and to inspect the transfer case. I need to check to make sure the driveshaft splines are not seized up but they seem to have a little free play to them.
View 2 Replies
I drive a 2006 Ford Focus. Last night, when I turned on my car, a number of things happened. (I should add that it was very cold, if that makes a difference)
1) My dashlights no longer work. The warning lights work fine, and I have checked the dial to make sure they are turned up, but I can no longer see what speed I am going when it is dark.
2) My taillights no longer work. One of the bulbs had previously blown, but now, the only ones that work are the rear blinkers.
3) My left driver side headlight is no longer working.
4) My trunk randomly kept popping open as I was driving. It has stopped doing so, but I am not sure if the problem is gone for good.
The mechanic wants to charge me $100 / hr just to even check the problem and indicated the diagnostics may take several hours. Having just replaced two tires, that option is far beyond my means.
View 4 Replies
My girl friend drives a 2000 Ford Focus manual 5 speed but she is hearing a rattle after she lets off the accelerator even in neutral with the parking brake on ?
View 5 Replies
So I have a 2000 Hyundai Accent, 1.5L with an automatic transmission. I'm hearing a grinding noise when I'm driving. It gets faster as the car goes faster, but the engine RPM has no effect only the speed of the car.
I got new tires, changed the CV axle shaft on both sides, and I also changed the front struts as I was told that one of the struts was bad the last time I took the car for an alignment. None of that has had any effect on the grinding noise.
Then I jacked the car up on both sides and let the wheels spin, and the grinding noise is present that way as well. Then I jacked up just one side at a time. When the driver's side wheel is spinning, the noise is audible, but not when just the passenger side is spinning.
I then disconnected the brake caliper from the driver's side and held it up with a tie wrap to keep it out of the way. The noise is still audible when the wheel is spinning, so it's not the pads or a clip or anything like that.
So now I'm down to a couple of ideas.
1) Wheel bearings
2) Something is hosed in the differential or transmission. I'm guessing that the differential is more likely, as the transmission should effect both sides the same, right?
I'm going to check the wheel bearings now, though to me it seems unlikely to be the problem.
View 10 Replies
I've had a grinding noise coming from the front passenger side, sounds like the wheel area of the car, for many months. I've driven thousands of miles on it like this, mostly because I'm broke and the car otherwise runs fine, but also because when I've taken it to mechanics, they are stumped.
I took it to a shop about a year ago and he had it for a week, had different specialists look at it and ruled out anything mechanical (wheel bearing, etc.) In the end, he threw up his hands and didn't want to give me any more free labor for his non-diagnosis, and thought he ruled out everything but the transmission. I took it to a transmission shop recently, and the guy ruled out right away that it was the transmission. He tried to diagnose the problem and was stumped too.
Here's what it is doing. It makes a grinding noise around the front passenger wheel when I accelerate. Only when I accelerate. It seems to be more active when it is cold, and after I've been driving the car for about an hour or so, it goes away. It used to only really happen when taking right-hand turns, and that is still when it is at its worst, but now it does it anytime. However--some days it is very bad and some days very light. One day--of course the day I designated to take it to the shop--it stopped altogether and drove like new. Just until I got it home. It is worse in low gears, and used to only happen in first, second and third, but now on an active day I can hear it on the interstate in fifth gear.
The shops I've taken it to can't seem to figure out what it is. Reading threads online, I've learned that people with similar problems found the problem was a bad passenger side motor mount. I have the car at a new shop right now, and I asked them to replace the motor mount, even though it looks fine. I had a long talk with the mechanic there today and he seemed a bit skeptical, but thought it was a possible solution.
Should I spend the money on a motor mount even if it looks okay? (I've also read that the Focus mounts look fine from the exterior when they are bad because they have a gel interior that busts). Especially if this doesn't work, I'm going to be back at square... um, zero.
View 3 Replies
Ford Focus 2012 - 25,000 miles
There's a loud grinding noise from the front end of car when I turn the steering wheel... even when the car is off and in park.I can post videos of the noise if needed.
View 2 Replies
So I just bought a 2004 Ford Focus. I did not drive above 15mph when I tested the car due to the lake effect snow that was occuring. Now that I own the car I have noticed if you try to stop going over 20mph the car starts to stop but last second it lurches forward a little bit. There is also a grinding noise that sounds like its coming from the back and a loud vibration that sounds like its coming from underneath the middle of the car. I'm trying to figure out if it is the brakes, tires or a leak in a brake line (those are all things my dad said it might be).
View 4 Replies
As I'm driving my ford focus I hear a growling noise from the right front. It goes away while turning left.I jacked it up and feel no play in the wheel. I'm thinking it is either the wheel bearing or the drive axle. How could I tell which one?
View 2 Replies
I have a 2004 F150 4x4 Fx4 supercrew with 5.4 engine and 46,000 miles. For the past three weeks now I have a periodic Grinding /scraping sound that seems to be coming from the front passenger's side of the truck. It can come on with light driving and braking in town or start while driving 70 mph down the interstate without even touching my brakes. The thing is I just about always have to come to a complete stop to make it go away. 10 Minutes later it comes again. It's loud enough for everyone around me to start staring at my truck. Sounds like metal scraping concrete and gets deeper as I slow down and when I fully press my brake pedal it goes "curchunk and the sound is gone for a while. I thought maybe my caliper was sticking or maybe the truck is trying to go into 4x4. One friend even suggested me to check the dust cover behind the brake for rocks.
View 12 Replies
2001 Ford Focus ZTS manual. Squeaking/scraping is the best that I can describe it, happens sometimes while driving maybe 20 mph. Also makes a rapid clicking noise when starting from a stop, groaning noise with engine on/off while turning wheel from same area. I did pads/rotors last year. I had play in the wheel, axle nut was loose, tightened and went away. I can't find any problems. It can make some noises under heavy braking and it was making noise from moderate braking, I'm guessing that's my cheap rotors.
View 2 Replies
I have a 2005 Ford Focus zx5, which has been a great car for me so far. I live in DC, and traffic is insane. Over the last year or so, maybe once every other month, my car has turned off when I come to a hard stop (usually braking suddenly at a light/pedestrian walkway). This is my first time owning an automatic, and it's just as if my car had stalled out. The radio will stay on, etc, but the engine dies and I have to put it into park and re-start it.
The RPMs have seemed to fluctuate a bit as well, usually on start-up or on hot days.
So far I haven't been motivated enough to get it taken care of, since it happens so infrequently and things seem great otherwise. What could be causing this?
View 3 Replies
I have a 2015 F250 6.7L and I am having problems with the brakes. When you first start the truck and put it in reverse and hit the brakes there is a continuous popping noise coming from the floor board and it can be felt in the brake pedal. It feels like the brake pedal is kicking back, once you drive the truck a little ways down the road the brakes work fine but if you hit the brakes a few times in a row like coming to a red light the noise is there again and it can be felt in the pedal.
View 3 Replies
I am having a major issue with my truck. I replaced all of my brakes about 8 months ago. Replaced everything. Rotors, calipers, pads etc. About 3 weeks ago I pushed on the brakes and they locked up and I heard a loud pop and then grinding. I pulled my wheel and my brake on the right rear had broke the 2 mounting bolts and fell off. So I put the brake back on thinking I hadn't tightened the bolts.
Drove about 7 miles and around the 10th time I stepped on my brakes it did the same thing. So I replaced the brakes again. Calipers caliper mount and pads. I have been driving it 2 weeks and all of a sudden same thing happened. I push on the brakes the right rear locked up and snapped the bolts again. So now I replaced everything rotor calipers etc. Greased everything up and no problems for a day. Do I need to replace the brake mount and where do I get that?
View 1 Replies
I start the car - a 2001 Ford Focus 4 cyl DOHC. It runs fine for 30 seconds then stops, as if it is no longer getting fuel. I can't start it again for a couple days then the same thing happens over again. FWIW, I parked the car for 8 months before this happened and only started it once in that time. But it ran fine then and before I parked it. What can this be?
View 1 Replies
I just replaced my front brake pads and rotors. Car had no squeaking sounds before this. When changing the right front pads and rotor, the set screw that holds the rotor in place snapped on me when I tried to remove it. I drilled out the remaining screw and inserted an easy out / screw extractor to try to remove the broken screw. Screw wouldn't turn/budge and eventually the easy out snapped in half while trying to turn it. Here is where I fear I made a little problem into an even bigger one; I tried to remove the broken easy out by banging the back end (smaller end) of it with a hammer and screwdriver, hoping it would pop out from the front of the hub. No success, and continued using a lot of force to try to remove it from the rear part of the hub. Eventually I noticed the hub area by the back of the easy out bent a little from me using force from the rear to remove the easy out. I stopped there, bent the hub section back to original shape (didn't bend too much to begin with) and sawzawed off the protruding end of the easy out from behind.
After driving a few times I started noticing the squeaking sound coming from the front right wheel, the sound sounds like is in tune/harmony with the wheel rotation. As soon I step on the brakes, the sound stops. I had a similar sounding problem with a rear wheel a long time ago and it ended up being that the bearing needed adjustment. I know the front bearings are pressed in so they can't be adjusted. I am thinking the force used to try to remove the broken easy out damaged something with the hub or bearing or maybe the axle nut.
View 2 Replies
I have a 2000 Ford Focus automatic dohc 157K. About two years ago, it started making a noise that has gotten progressively worse. It is very hard to describe. It sounds like an intermittent flopping noise that you would expect from a bad tire. What makes is strange, is that the sound is not consistent with the rotation of the wheels. It does however increase and decrease with speed, but again it's inconsistent with the wheel rotation. It does not roar, or whine like a bearing, and there is not popping noise you usually get with a bad CV joint.
It seems to subside when I turn to the right and become a little more pronounced when I turn to the left. I have new tires, a new axle and wheel bearing on the right (passenger) side of the car. The repair shop checked all of the bushings and bearings, and cannot hear the noise when it is on a lift. I also just changed the sway bar links and all the engine mounts. You can feel the floorboard bumping along with the sound, but it does not telegraph through the steering wheel. There is no shimmy or vibration.
View 5 Replies
I have the po411 code, not sure which problem it is but when I first start the car it sounds awful like almost a grinding or rattling noise then stops after a few seconds.
View 3 Replies
my 2000 focus se, 2.0L SPI, with 82k began to recently run rough at idle then progressed to stalling at longer lengths of idle. The condition starts once the engine warms after 2-5 minutes. I 1st tried gas treatment. I replaced the ignition coil as suggested in the other threads, but it has not improved the problem. I had the fuel pump recall-replaced 2 years ago. I would guess that a bad fuel pump would exhibit loss of power at all engine speeds? Before I proceed to replace plug wires and plugs.
View 14 Replies
I recently inherited an s10 that works fine but has a very quirky condition. The engine will stop randomly with no warning while driving down the road after turning off the ignition, wait a minute or two, turn it back on and it works fine for a few more days or couple of weeks, but has been driving me crazy, and isn't very safe The check engine light is on and the code read a bad crank sensor, so I got that replaced, and it didn't fix the issue so the mechanic said that the next step would be to replace the ignition module with the ignition coils.
View 1 Replies
