I have a 2000 Ford F150 lariat with the 5.4 liter engine. At least once or twice a day, its like the starter hits a bad spot and will spin but not engage the flywheel. It has a new starter, battery, and solenoid. What this might be?
View 1 RepliesI just bought a 2000 f150 4x4 ex cab with the 5.4. Once in a while when starting, there is a grinding and the starter won't engage the flywheel. The truck has only had 17000 miles put on it in the past 4 years, and has sat quite a bit. Could the starter gear be gummed up and not engaging all the way, or should the starter be replaced? Or could poor contact on the cables cause this? Or is this a flywheel issue?
View 14 RepliesAfter getting the oil changed in my 1997 Ford F-150 4.6L with 150K miles at a local quick lube, I made one stop and my truck wouldn't start. I could hear the starter engage the flywheel, but couldn't turn it over at all. Oil was clean and full. I bench tested the starter and it tests good. I put a breaker bar on the crankcase nut and I could barely move it. Oil level was about 2 quarts low before oil change.
View 10 RepliesThe starter in my '93 Dakota was dying (usual signs of worn brushes) so I replaced it with a new one from AutoZone. The starters looked the same, and after calling back to double check the part #, the store swears it's the right part. However, when I engage the starter, it spins but the pinion gear doesn't engage the flywheel. I can't see how I could have installed it wrong - the two bolts seem to have only one place they can go.
View 19 RepliesCame home from a trip and the Santa Fe had been parked for 3 days. No starting issues prior, but went to move it and no go. When I turn the keys something "spins" but the starter does not engage. 99% sure it needs replaced. 02 GLS V6 AWD
View 4 RepliesMy starter motor in my 2004 Golf 2.0 doesn't engage or spin when it is very cold. By very cold, I mean below 5F.
The battery has plenty of juice, and jumping the battery doesn't work. I turn the key to "start" and nothing happens. When key is in the on position, fans, wipers, etc all work fine. When the car warms up to 20F or so, everything is fine and the car starts.
Here's the funny thing. If I put a little space heater on the driver side floor to warm up the fuse and relay panel, it starts with no issue.
I don't know enough about the interlocks between load reduction, starter motor, ignition switch etc to make a good guess as to which relay (if any) may stick in extreme cold. It's a tough problem to diagnose, because I can only experiment when it gets REALLY cold, when it isn't very fun to experiment anyway. I don't think it's the piggy back harness, because the wipers, horn and fan all work.
I have a 1992 for explorer XLT 2-wheel drive Automatic 4.0 engine. The starter started grinding against the fly-wheel. Changed the starter and the same thing happened. There is no shim for this starter. I took it down and checked the flywheel--as much as I can see through the starter mount hole and the teeth on the flywheel are great. There is only the slightest point of impact where the starter is just grazing the flywheel.
I also grabbed the flywheel to look for looseness, thinking it might have broken and/or warped and I just can't see where it broken because of the small hole. It's solid! It's as if the whole thing just moved back about an inch and a half... I texted both the old and new starters with jumper cables, and the make certain, I took them to the local parts store and they also texted them. While both of the starter were fine, I'm not!
Four months when you tried to start the vehicle sometimes you will hear the starter. Drive in gauge but not meet the flywheel. Sometimes it would take three or four tries to turn over the engine. Yesterday went out to start the engine turn the key nothing happen no noise nothing but all the lights were working OK..
The repair shop said it was not the starter but flywheel missing teeth. But they said the main thing wrong is a need of new battery terminals. They change them in the truck started fine last night Today when my wife try to start it then come home saying thing happen nothing no sound, no nothing. Am I dealing with a bad starter solenoid perhaps or a combination of a bad flywheel??
In a matter of weeks, my truck destroyed two sets of flywheels and starters. When the ignition key engages, the engine "jumps back?. Apparently, this causes the starter and flywheel teeth to grind. My mechanic cannot determine the cause of the "jump back". He thought that it might be the timing. His examination and testing, however, proved the engine properly timed.
View 6 RepliesI have a 2005 F350 w/6.0 turbo diesel. Had starter replaced last spring. Went to store recently, came out & truck starter would just wind and whine, no flywheel engagement. Mechanic replaced Napa starter under warranty and now the starter whines when just trying to connect the battery(s) without even turning the key. I did try several attempts at starting truck when stranded at the local store, with no results but starter whining. Could I have created a dead short some where, and where would be a good place to start?? How do you get a schematic of the starting system?
View 2 RepliesMy 1996 ford f150 4x4.. The problem is with the front drivshaft it does not turn even when the 4x4 is not engaged. The 4x4 works and engages and disengages properly but when it is not in 4wd the front driveshaft does not spin freely..
View 1 RepliesThis issue has been happening for a few weeks now since it has been around -10C here. When I start the car it starts just fine but then the starter grinds against the flywheel (same as if you tried to start while car already on). I did a quick search and found that the relay may be faulty, Car is at 87000 kms.
View 5 RepliesI have a Chevy Tahoe 1999, Went to the store came out my Tahoe wouldn't start i had it towed home. My husband said the starter was clicking but wasn't getting enough power to turn the flywheel. We got a new starter put it on and it clicked just like it did when i tried to start it before. We took the new starter back and had the old one tested and it was ok so we put it back on and it still clicked like before. He said the flywheel was easy to turn, then he replaced the hot wire from the battery to the starter, now the starter don't even click.
View 17 RepliesI have a 2001 Santa Fe 2.7l automatic. I recently changed out the automatic transmission (transaxle) as the old one had died. Now the starter motor plunger is not disengaging quick enough on start up and a screaming noise is made as flywheel turns as engine first turns over. I have just put a new starter motor in with exactly the same (screaming) result. The flywheel looks to be in reasonable condition as I inspected it when being put in, no teeth mangled and all teeth there. The transmission replacement was from a wrecked vehicle, I was told from same model vehicle but maybe a 2003 Santa Fe.
View 1 RepliesI am back with the same issue as the last 2 batteries. Ever since the wife has had this car, the last 2 batteries would spin the starter, but it wouldn't run. Bought batteries and it fixed it.
But damn, now her battery is only 13 months old. Is it true that if the battery gets just week enough that the motor is starved for enough juice for it to run?
Last dealer couldn't figure out why she needed a battery when the one she replaced was good. I told them do it anyway, and it worked, last year.
She called the dealer today and their saying its the alternator is pulling it down. I say BS. Its not a dead battery, its a temperamental motor, I guess. I dont know what to do. This is getting old.
Pulled 3 starters at the junkyard to replace one that has a bad solenoid. Have a 2002 Buick Regal LS with 3800 series II engine. Found some on 3100 engines and one from a 3800. My starter has about 10 teeth on the gear that engages the flywheel. Some of the ones I pulled had smaller gears with only about 8 teeth.
Why the difference? Also one GM Delco starter was slightly longer (about 1/2 inch) than mine and had a small black hollow tube about 1 inch long at the rear of the starter and at the bottom. It fell off when I touched it. Looks like it might be a drain hole in case some water gets in to the starter. What is this really for?
I have a 2011 sonata SE w/ 30K miles, the starter failed on me.
The motor would spin but would not engage the gears b/c of the solenoid or the rod malfunctioned.
They towed my car to the dealer for free and it was replaced but I'm concerned because the towing guy told me he towed quite a few Hyundai's b/c of this problem.
I have a 1998 chevy blazer and I cant get it to start. I removed the starter and turned the key and can see the starter popping out and spinning, but when I put it back into the flywheel all I get is clicking noise(like if the battery is dead) I had it on jumper cables so I don't think its the battery?
View 12 RepliesThis is about a 2011 Sonata. I picked it up for my son.
The car has been running really well for the past few months, then out of the clear, when trying to start the car, the starter does a quick spin-free, then a short whine. The battery voltage is at 13.1 prior to attempting to start.
The car finally started under a jump from another car, but only after several turns of the key. And with each turn of the key, was the spin-free, then short whine, like described above. It's like the starter had a dead spot -or several dead spots- and I caught it just right, and it started.
I have the battery on an overnight charge. It sound like the starter to me. What do you think? And if it is the starter, how big a deal is it changing it out?
I am having trouble with my air conditioning system in my 1996 Chevy Lumina. When I turn on the AC, the compressor clutch does not engage and the fans do not spin. I was able to jump the compressor so the clutch engaged, however, the fans still did not spin and the AC was not cold. I then jumped the low pressure cycling switch (near the accumulator), which caused the fans to spin while the compressor was running. However, this still did not produce cold air from the AC and none of the AC lines were cold to the touch. I am starting to think the system is low on Freon, but I do not have gauges to test the pressure.
View 2 RepliesI just bought an FX4 and pick it up tomorrow. When you are in 2wd does the whole front end spin like the axles? Or does only the wheels spin when you are in 2wd? Reason I am asking it seems like with chevy the whole front end spins in 2wd.
View 8 Replies