I have the subject truck and do my own oil changes. I see that the front end has sealed ball joints and doesn't require lubrication.
Do the universal joints on the drive shaft or any other components require lubrication? 2014 F150 XLT ....
I need to identify the part numbers for the u joints in the rear drive shaft. The guys at the auto parts store kept telling me I only need two until I showed them that there are clearly three. I just want make sure that I get the correct parts before purchase.
View 5 Repliesits a 2000 limited 4x4, must have been in the snow a lot because it was from up north and is pretty rusty on the underside. my dad and i have tried everything to get these caps off but nothing will work. lots of pb blaster, hammering, even cutting the one of the four joints and trying to wedge something from the inside. If we cant get it could a shop do it? and how much might they charge?
View 9 RepliesI have a 2014 4WD Super Duty. It has a squeak that is coming from the drive shaft area. I had someone listen to it as I drove slowly next to them. It is a repetitive: squeak squeak squeak squeak squeak. Not loud. The frequency increases as speed increases. I could believe it may be a U joint based on the frequency, but seems hard to believe with a new truck. I heard this sound when I first got it, but the sound was so slight that I thought it was just some sound associated with a newer engine. But now it is becoming a bit louder.
View 4 RepliesI have a 2012 f150 supercrew with the eco boost. While driving down the highway my rear tire passed me. After crashing I looked at the rear end and the wheel and hub had broken off of axle. Scared the crap out of me. Would this be a warranty issue?
View 14 RepliesI have a 2010 F150 with the 5.4 V8. How many cam shaft position sensor do I have ??? I replaced one but I swear I see one one the passenger side...
View 1 RepliesI am replacing the ball joints on my 07 f250 4x4. got down to the removal of the shaft itself and it won't budge. What is the secret here. Have to go to work on monday, and the weather in Cleveland isn't going to be very good on Sunday.
View 10 RepliesI have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 RepliesI have a 2010 f150 crew cab with the 5.4 and I've noticed a ticking noise when I drove through town the other day. I got home put the truck in park and the ticking went away but when I put it in drive, held the brake and gave a little gas it came back even though I was not moving at all. What could this be?
View 4 RepliesI've had my truck start making a nice CLUNK from the vicinity of the rear axle when starting moving from a standstill. (and it's a pretty decent thunk sometimes, you hear it AND feel it). I called and made an appt to bring it in and have it checked out (also having the first oil change done and gonna see if they can figure out why the automatic headlights are almost always on even on a bright sunny day) ...
View 14 RepliesI have a 2012 F-150 STX 4x4 with the 5.0 liter. I have noticed that when I put my truck in to reverse and sometimes drive I get a click sound. I jacked up the truck thinking it was the drive shaft that was loose but it wasn't... But I believe it is coming from the rear end. I found a video of the sound on youtube.
Check it out : 2013 F150 Rear End Click - YouTube .....
Does the 2014 es300h have a timing belt that requires changing at specific intervals? The dealer told me he thought they are using a timing chain hence no scheduled maintenance.
View 6 RepliesJust had my 2010 F150 in for a loud knocking noise when the truck has warmed up in drive and rpm up to about 800. I can't hear the noise when I disconnect the passenger side vtc selonoid. The Tech who worked on it has recommended replacing the motor. His troubleshooting on the ticket says he removed the coil from the number 4 cylinder and the noise he hears goes away. I just can't see that the motor is bad.
View 8 RepliesThis morning, the driver's heated seat in my 2012 Lariat did not seem to operate properly. (It worked fine approx 14 hours earlier.) Note that my seats have both the heat and cool options.
I started the truck (its NOT garaged and the air temp was -5 F, which has been kinda typical lately) and turned on the driver's heated seat to high (level 3). I noticed that the seat's 'air noise' was more than normal (I've always noticed a more air noise with the 'cool' setting .........
No, I was not using 'cool' instead of 'heat' !) and that the seat never warmed up during the 10 minute drive. (Normally it would be noticeably warm in less than 5 minutes.) The 'air noise' seemed to cycle off/on toward the end of the drive. I did not have a passenger, so I did not have a chance to try that seat.
I've owned the truck about 2 years and had never run into this before.
Last time this truck did this, I replaced the #27 fuse and it started right up. This time, no such luck. It is EXTREMELY frustrating to pay this much money for a truck that you cant start. Btw, it has 38 miles until its on empty.. Any way that could be the cause if i am parked in my drive way which has a slight incline?
View 3 RepliesI have a 2011 XLT 5.0 V8 with 133,260 miles. I have extended warranty for the next 12,000 miles...which is great because I drive about 400 miles a month... Anyhow it runs great but for one small issue (hopefully) that has been intermittent.
She likes to idle slightly rough in drive at a stop or very low speed, and in reverse at slow speed. If I don't maintain the RPM it will stall and the low oil pressure light will come on, which I imagine comes on because of the sudden stall.
I first noticed this while backing into my garage in the driveway, It would fluctuate in RPMs and if I didn't maintain the gas it would shut off. I took it to the dealer and all they were able to tell me was the Tranny fluid was low and it would cause it to shut off at incline because a sensor isn't detecting fluid in the tranny. I thought this was weird but being as I have never owned an F150, I didn't know better.
It was fine for a little over a month and it started doing it again at stop lights and backing into my driveway. It has become frequent but there is no issue driving at speed and on the freeway. There is no stuttering or shaking and if it weren't for the fluctuating RPM at a stop and the stalling, it would be hard to tell if there was an issue.
All I can note is that there is a clicking sound under the hood, if I remember correctly the last time this happened I was at a 1/4 tank of fuel like I am now, I also feel like it may be a throttle body issue, or some sort of air sensor, I plan on taking it to the dealer but I figure I would get a more informed answer on the forums.
I also hear this is a common issue with the 5.0s... I purchased the truck in December and since then I have only put 250 miles on it.
5.0L ... I'm having one of those moments, you know after you do a mod to your truck and all of a sudden you notice something about your truck that could have been there all along but now you notice it as something new? Ok earlier in the week I had my exhaust resonator removed and replaced with a straight-pipe by a reputable exhaust shop. IMO the work looks to be pretty good for what it is.
That said I have always been nervous about getting exhaust work on any vehicle because it always seems like tampering with or removing the OEM plumbing for aftermarket or custom work tends to develop a vibration at some point.
So here is what I've noticed over the last couple days, when driving my truck it is extremely smooth, almost like glass. When I come to a complete stop say at a traffic light about 1-2 seconds after making the complete stop I feel this slight harmonic vibration in the steering wheel. For those of you that have an iphone it would be like having your phone bolted to the steering shaft somewhere and it on constant vibration if that makes sense.
Just to prove it only happens when I'm sitting still and idling in (D)rive I sat in my driveway with the truck idling, set the park brake and released the brake pedal holding the truck in place in (D)rive with the parking brake. No vibration, smooth as glass engine idle, as soon as I put my foot back on the brake pedal the vibration comes back. It's as if the extra draw of applying the brakes puts an extra load on some sort of accesory drive or componant under the hood and the result is this harmonic vibration.
Just so everyone knows, the vibration is very noticeable to me because I drive the truck daily, most people wouldn't pick it out if I didn't tell them first. Case in point if my wife drives the truck she can't feel it unless I tell her what to look for. There are going to be some of you that just say my truck doesn't do this and has had a smooth idle for XX,XXX miles I believe you but let me know now that I have explained exactly what to look for. Like I said for all I know it's done this since day one.
I have a feeling that the straight pipe might have been welded in slightly longer than the oem section that was removed thus putting more tention on the exhaust and engine if that makes sense, the end result being a slight vibration?? I know that manufactures put these little rubber bushings along the exhaust system on cars/ truck to absorb harmonic vibrations and for all I know my resonator might have been designed to balance out harmonic vibes in the exhaust system as well as quiet down the exhaust.
I had the universal joints replaced on my 1999 Ford Ranger now it vibrates badly starting at 45 mph and when I coast at 65 mph the vibration is very significant. The mechanic does not know what is causing this. I never had this problem before changing the U-Joints and I have 171,000 miles on the truck.
View 4 Replies2007 XLS Crew Cab 2wd. 60K miles When going through the 35 to 60 mile per hour range there is a vibration that seems to come from the drive shaft. Let off the gas and it goes away. After 60 mph it seems to be gone. I am thinking Trans support, motor support? One of the postings on this sight made me wonder about the transmission. By the way, I just bought this truck used and love it. Can I run flex fuel in the 4.6L engine?
View 1 RepliesI purchased a 1990 Ranger 4x4 with a v6 from auction. Took it to local shop to have them check it for me. Found out that it has a 3.0 in it and mechanic believes it is from a taurus. Truck actually runs extremely well. Has a few codes due to the ECM is for an automatic trans. Now the problem. I was on the highway-in 5th gear. Terrible noise the nothing. When I got it pulled over. The drive shaft was hanging from the rear end. It had been twisted like a straw. The transmission side had the yoke only, and the tail housing was cracked. It rolls and the drive shaft at the rear end turns. I figured the trans locked up. I don't know what trans to look for---is a 90 2.9 5 speed the same on a 3.0 ??
View 6 RepliesI am wanting to remove my front drive shaft from my 2004 Aviator for a couple of month's while I save money to have my transfer case replaced. Are there any safety concerns with this? just need a couple of month's to get the money together....
View 5 Replies