Ford F-150 (2009-2014) :: 2011 - Loud Grinding Noise From Front End Of The Truck
Dec 30, 2013
Today I was out getting lunch in my Ecoboost When it started making an extremely loud grinding noise from the front end of the truck. My first thought was I blew a turbo. After holding the break and building boost I discovered it was not the source of the noise. Also the truck runs perfect and there is no smoke. I then took it to my friends auto shop and pulled both front tires off to check and see if anything break related came loose. We found nothing. The noise only happens upon acceleration or cruising throttle, as soon as you let off the sound goes away. So after I found nothing I took it to ford and what would cause that, but they assured me that they would have my truck for a long time while they figure out the issue.
View 14 Replies
Advertisement
This evening, my F150 with 2,600 miles developed a high pitched squeal, much like you might experience on an older vehicle with failing front brakes. Yes, that same squeal/grind the brakes make...metal on metal. It came in instantly while at highway speeds. It was VERY loud. The pitch didn't really change with speed...it was pretty consistant going slow or fast. There was no vibration, chatter or growl as I would expect with a failing bearing.
It was definately in the driveline/brakes. I was 10 miles away from a friends house, so I turned around and took it back to his place. Shortly after turning around, it quieted, only sounding when I would turn ( like a wheel bearing would when being side loaded ). I looked at the brake disks, thinking something was grinding on one of them. The outsides of the disks looked fine. Due to the shields on the inside, I couldn't see.
Later in the evening, I had to drive it back home, about 50 miles. Again, it was quiet unless turning fairly hard. By the time I got home, the squeal had turned into an intermitant growl/thump, as if a warped rotor was banging on the caliper. The noise was 1 to 1 with the rotation of the driveline. But still no vibration. Brakes work perfectly and the noise doesn't change with brake use. Backing up and turning hard results in a variety of sounds, including squeaks.
The hubs and CV joints felt cool. The brake disks were not hot as if they were dragging.
It is 4x4 / 3.7l
View 14 Replies
I have a 2wd 2011 F150 90K with grinding noise coming from the drivers side front tire. Even though it was happening when coasting I thought it might be pads but they are real good. Turning the hub with no tire on it I can hear a little grinding. So I suspect bearings. I want to remove the hub but can't find out how to pull that off.
Where I would expect to find a spindle nut there is an area where it looks like you put a puller in. Can't find any videos or other information on the "Internets". Maybe I'm the first to have bad bearings? Anyway, how to remove the hub?
View 9 Replies
Just had my 2010 F150 in for a loud knocking noise when the truck has warmed up in drive and rpm up to about 800. I can't hear the noise when I disconnect the passenger side vtc selonoid. The Tech who worked on it has recommended replacing the motor. His troubleshooting on the ticket says he removed the coil from the number 4 cylinder and the noise he hears goes away. I just can't see that the motor is bad.
View 8 Replies
Whenever Im driving at slower speeds - parking lots, side streets, etc I get a squeaking/squelching sound coming from somewhere in the front end of the truck. I thought at first it may have been a rattling heat shield someplace under the truck, but now Im not so sure. No loss of power, check engine light, or anything of that nature has occurred so Im not sure what to do. Its a 2010 Ford F150 XLT 4wd ....
View 5 Replies
Wife's 2010 F150 4x4 85000 KMs makes grinding / ratcheting noise in LH front axle when in 2 wheel drive. Mostly when turning left some times when traveling straight never when turning right. Never makes the noise when in four wheel drive. I am suspecting the auto hub is the issue but wonder if others have had this trouble ?
View 5 Replies
First off I have a 2009 F150 4wd 4.6L truck...we have noticed a grinding noise on the front driver side wheel...we have replaced the auto locking hub acuator and the hub assembly but the noise is still there....it has us puzzled now not sure what it could be. I have read many different threads on this issue an it seems that it might be something to do with the vacuum. The noise is only on the driver side and only in 2wd, when its in 4wd it doesn't make the noise at all. Also while in 2wd the noise seems to go away when we let off the gas.
View 5 Replies
Just installed new actuator and wheel hub assembly on my 2009 f150,truck still had grinding noise in front passenger wheel , New solenoid and vacuum hose kit installed when test drove noise still there until you put the truck in 4 wheel drive it disappears . The noise returns as soon as you take it out of 4 wheel drive. Also mechanic said steering was tight,installed new shaft same thing, could this be the rack and pinion.
View 5 Replies
I replace my brake pads and rotors in the fall of 2015 with EBC parts. Now almost 13,000 miles later, I started hearing grinding and metal-on-metal contact in the front. So I went out and got PowerStop pads to replace the EBC (EBC had way too much brake dust). I took off the front wheels and noticed that the DF pads had about 1/32 left on them, ok I guess its time to change them out. Onto the PF pads, I find that there is almost no material left, in fact I could scrap off what was left of the material. I decided to do a rotation while I am at it and noticed that the rear brake pads on both sides look like I never used them!! Is it really that possible to have 2 stuck calipers, both on the rear at the same time?
View 2 Replies
2011 F150 Limited 4wd 6.2 liter. I just bought the truck a few weeks ago with 26,000 miles. Late last week I began hearing a mild grind/rustling noise that appears to come from the driver's front. It's not terribly loud (loud enough to hear), but it's annoying. It happens when I slow down (on and off the brake and below 25-30 mph) as well as let off and begin to speed up. It doesn't last but a second after I let off the brake and speed up though. The kicker is it does not happen all of the time. I drove it home from work last night and it did not do it one time, but driving to work this morning it happened every time I did what I described above. I have taken it to our local tire/suspension shop and they claim they could not reproduce the sound which does not surprise me. They did a full inspection and found nothing.
View 14 Replies
I have a 2009 Toyota Corolla and it's making a loud grinding metallic noise on the front left side. It does it while I drive the faster I go the louder it gets. When I turn to the left it makes it louder, when I turn right the noise decreases. PG&E have been breaking the roads by where I live and there's a lot of little rocks I drive thru. I'm wondering if that's the problem?? What do I do?
View 4 Replies
So today was the hottest day I've encountered, since purchasing my '13, FX4, EcoBoost. It was 91 degrees out, which I know isn't THAT hot for some parts of the country.
That said, it's the first time since I've owned my '13, EcoBoost that I needed to use A/C all day. One thing I noticed is that the A/C fans are EXTREMELY loud.
The noise outside seems louder than an early 6.0 Powerstroke idling, or say even the 7.3 PSD. Sounds like a 747 taking off.
Is this normal or is something wrong with my truck? If I turn the A/C off, the super loud fan turns off, and the low speed fan for what I assume is the radiator keeps on, but is barely heard.
I don't remember the A/C fan being that loud on my previous truck '11, 5.0, XLT, but it had more equipment, and the engine wasn't as quiet as my EcoBoost now, which is almost silent.
View 14 Replies
Chasing down a grinding noise. I have done a lot of research but nothing quit matches up with what I am hearing.
I have a 1979 F250 4x4. A few days ago I put the truck in reverse and as I was backing up it was like the drivetrain locked up. After that I put the truck in gear and started on my way. As I got up in speed a pretty loud grinding noise was coming from the tranny. 2nd and 3rd gear aren't bad but when I get up to 40+mph it sounds like crap. If I push in the clutch the grinding is still there. While driving I also put the transfer case in neutral, kept the tranny in gear, pushed in the clutch and the grinding stopped.
I also took the lid off, inspected the forks and thoroughly cleaned the inside but noise still continues.
View 6 Replies
I have a 2011 5.0 screw with 3.73 gears. Today my wife has the truck to haul stuff for her craft show. She calls and says the truck keeps stalling, like she had to keep restarting the truck 3-4 times to back up 10 feet. The dealership we bought it from is going to pick it up and give us another truck to use while they figure it out.
View 9 Replies
It's a 2011 xlt ecoboost with 14000 miles. Just started getting bad where it literally jars the whole truck. It only does it once. After I'm in 2nd then go back to 1st at a stop, it shifts fine back into 2nd. If I let it warm up for around 10 minutes or so it doesn't happen.
View 6 Replies
I purchased a 2011 F150 XLT 4X4 Super Crew in early January, since then I have had it into the dealership many times to correct an annoying shudder that can be seen (looking at the steering wheel) and felt as the truck accelerates. The shudder happens around 5 kph or 3 mph and then quickly disappears as you accelerate.
This is extremely annoying in stop and go traffic and is more readily felt if driving up hill. The dealer tried shims in the differential, Installed a new rear drive shaft, U joints and the last attempt was a complete rear end all to no avail.
View 14 Replies
The doors on my truck were leaking water into the cab due to poorly adhered splash shields on the interior of the doors. The splash shield sits between the door shell and the trim panel.
Signs of the leak are water pooling in the groove in the weather strip at the bottom of the opening. Mine were pooling water at the front of the opening and when the door was opened you could see the water running down from behind the door panel.
If you have a water leak along the door opening on a newer vehicle, make sure your dealer checks for this new TSB. It was supposedly only put out in the last week.
View 4 Replies
Issues:
1. Backup camera sporadically does not come on in rear view mirror. Has already been replaced by Ford dealership.
2. Backup camera settings Visual Park Aid and Guidelines sporadically are set to 'off'
3. While truck is running, start seeing warnings/hearing chimes. Emergency Brake (which isn't set), Engine Overheating, Check 4X4, etc.
4. Truck will NOT start. Won't even attempt to turn over. When this happens, I have a radio but the LED screen is usually blank.
These sporadic issues are starting to seem to be related to the use of the emergency brake. Use of the emergency brake does not always immediately cause issues. Now that I feel like there is some kind of connection, I have been setting the e-brake when I park it (even if not needed) trying to force things to happen because Ford says if they can't make it happen they don't know where to look/what to fix. I can't always make things happen by using the e brake...but am noticing things happen more often when I DO use it and when things happen (like backup camera won't work) setting the brake will make it come on and then I can release it and back up. If it won't crank while the brake is set, releasing it will cause it to crank. The other morning when I had all the warnings/chimes going off setting the e-brake made everything go back to 'normal'.
Yesterday when I came back from lunch I parked and set the e brake (on level ground). Got in it to leave work, left e-brake set, stepped on regular brake and tried to crank....nothing but radio. Called dealership. They had me try putting the key in, pressing the regular brake, and try to move the shifter from Park to N. Shifter wouldn't move. Then asked to turn key to just get it 'active' and try again. Shifter wouldn't move. Asked me to turn the key to crank and try again. Same thing - shifter wouldn't move. Truck finally cranked after I released e brake. Came home, parked and set e brake and turned it off. It re-started right up with e brake still set.
View 14 Replies
So my truck hit 1,000 miles. I decided to change the oil to get the factory oil out and remove any material that may be in there from the break in. I know the motor hasn't fully broken in. My question is what is the purpose of that shroud under the front of the truck? It seems like it can almost get caught on parking bumpers. It also makes it very difficult to get under there and change the oil. I had to go from the side. Need to remove it? It seems to be held by 2 good size bolts by the frame.
View 14 Replies
I have a 2010 XLT, 85K, just started having a horrible grinding noise at start up for about 2-3 seconds, then gone. Going to dealer tmrrw. Multiple people said, possible oil pump hydraulics, ??????. Whatever it is, they say its expensive!!!!!
View 3 Replies
There is a grinding noise when i make a turn,when i straighten out it's fine,when i bought the truck in 09 i had a shudder problem but that was repaired by greasing the spline in the drive shaft. Truck has 59,000 and is coming up on the 60,000....
View 1 Replies
