Ford F-150 (2009-2014) :: 2011 2WD - Grinding Noise From Driver Side Front Tire
Mar 11, 2014
I have a 2wd 2011 F150 90K with grinding noise coming from the drivers side front tire. Even though it was happening when coasting I thought it might be pads but they are real good. Turning the hub with no tire on it I can hear a little grinding. So I suspect bearings. I want to remove the hub but can't find out how to pull that off.
Where I would expect to find a spindle nut there is an area where it looks like you put a puller in. Can't find any videos or other information on the "Internets". Maybe I'm the first to have bad bearings? Anyway, how to remove the hub?
View 9 Replies
Advertisement
First off I have a 2009 F150 4wd 4.6L truck...we have noticed a grinding noise on the front driver side wheel...we have replaced the auto locking hub acuator and the hub assembly but the noise is still there....it has us puzzled now not sure what it could be. I have read many different threads on this issue an it seems that it might be something to do with the vacuum. The noise is only on the driver side and only in 2wd, when its in 4wd it doesn't make the noise at all. Also while in 2wd the noise seems to go away when we let off the gas.
View 5 Replies
2011 F150 Limited 4wd 6.2 liter. I just bought the truck a few weeks ago with 26,000 miles. Late last week I began hearing a mild grind/rustling noise that appears to come from the driver's front. It's not terribly loud (loud enough to hear), but it's annoying. It happens when I slow down (on and off the brake and below 25-30 mph) as well as let off and begin to speed up. It doesn't last but a second after I let off the brake and speed up though. The kicker is it does not happen all of the time. I drove it home from work last night and it did not do it one time, but driving to work this morning it happened every time I did what I described above. I have taken it to our local tire/suspension shop and they claim they could not reproduce the sound which does not surprise me. They did a full inspection and found nothing.
View 14 Replies
Today I was out getting lunch in my Ecoboost When it started making an extremely loud grinding noise from the front end of the truck. My first thought was I blew a turbo. After holding the break and building boost I discovered it was not the source of the noise. Also the truck runs perfect and there is no smoke. I then took it to my friends auto shop and pulled both front tires off to check and see if anything break related came loose. We found nothing. The noise only happens upon acceleration or cruising throttle, as soon as you let off the sound goes away. So after I found nothing I took it to ford and what would cause that, but they assured me that they would have my truck for a long time while they figure out the issue.
View 14 Replies
This evening, my F150 with 2,600 miles developed a high pitched squeal, much like you might experience on an older vehicle with failing front brakes. Yes, that same squeal/grind the brakes make...metal on metal. It came in instantly while at highway speeds. It was VERY loud. The pitch didn't really change with speed...it was pretty consistant going slow or fast. There was no vibration, chatter or growl as I would expect with a failing bearing.
It was definately in the driveline/brakes. I was 10 miles away from a friends house, so I turned around and took it back to his place. Shortly after turning around, it quieted, only sounding when I would turn ( like a wheel bearing would when being side loaded ). I looked at the brake disks, thinking something was grinding on one of them. The outsides of the disks looked fine. Due to the shields on the inside, I couldn't see.
Later in the evening, I had to drive it back home, about 50 miles. Again, it was quiet unless turning fairly hard. By the time I got home, the squeal had turned into an intermitant growl/thump, as if a warped rotor was banging on the caliper. The noise was 1 to 1 with the rotation of the driveline. But still no vibration. Brakes work perfectly and the noise doesn't change with brake use. Backing up and turning hard results in a variety of sounds, including squeaks.
The hubs and CV joints felt cool. The brake disks were not hot as if they were dragging.
It is 4x4 / 3.7l
View 14 Replies
I purchased a new 2011 F-150 Lariat, Ecoboost, SCrew, 4x4 last weekend. I love the truck. It is very comfortable, the Ecoboost has been incredible, and the ride is very nice. I am looking forward to towing my ATVs after I hit 1000 miles.
Yet, I have one problem. I get an incredible amount of wind noise and wind whistle from what appears to be the driver's door. I read other posts about wind noises and wind whistles (e.g., bug shield), but they do do not apply to me.
I'm planning on dropping it off at the dealership this week for them to take a look at.
View 14 Replies
I have a 2010 f150 supercrew 4x4 with 8.8 3:55 nls rear differential. my driver side tire has a wobble to it it is wearing the inside of the tire. i have replaced the driver axle shaft with new ford oem shaft put in new axle bearings and seals on both sides and have replaced the spyder gears and i still have the wobble I don't know what is going on. the wobble is more pronounced when the tire and rim are bolted to the shaft only without the drum and caliper attached. with caliper and rotor attached i still have the wobble just not as bad however the tire wobbles going down the road more noticeable between 20-45 mph.
View 13 Replies
2011 F150 Screw FX4 drivers seat squeaks. Its in the bottom. It happens when you go over bumps. It doesn't do it all the time, but you can sometimes make it stop by moving the seat forward or back.
View 3 Replies
Wife's 2010 F150 4x4 85000 KMs makes grinding / ratcheting noise in LH front axle when in 2 wheel drive. Mostly when turning left some times when traveling straight never when turning right. Never makes the noise when in four wheel drive. I am suspecting the auto hub is the issue but wonder if others have had this trouble ?
View 5 Replies
Just installed new actuator and wheel hub assembly on my 2009 f150,truck still had grinding noise in front passenger wheel , New solenoid and vacuum hose kit installed when test drove noise still there until you put the truck in 4 wheel drive it disappears . The noise returns as soon as you take it out of 4 wheel drive. Also mechanic said steering was tight,installed new shaft same thing, could this be the rack and pinion.
View 5 Replies
I replace my brake pads and rotors in the fall of 2015 with EBC parts. Now almost 13,000 miles later, I started hearing grinding and metal-on-metal contact in the front. So I went out and got PowerStop pads to replace the EBC (EBC had way too much brake dust). I took off the front wheels and noticed that the DF pads had about 1/32 left on them, ok I guess its time to change them out. Onto the PF pads, I find that there is almost no material left, in fact I could scrap off what was left of the material. I decided to do a rotation while I am at it and noticed that the rear brake pads on both sides look like I never used them!! Is it really that possible to have 2 stuck calipers, both on the rear at the same time?
View 2 Replies
I recently acquired a 2011 F150 Platinum. Nice truck! It has the automatic deploying running boards. They're nice but one problem: the driver side board takes about 15-17 seconds to retract after closing the door. This is way too long a time. The passenger side retracts after only 2-4 seconds, which is good. The dealer researched this to see if there is any way to adjust the driver side, but found nothing. I'd like the driver side running board to retract sooner after closing the door, like the passenger side.
View 1 Replies
I have a 1996 Ford Explorer (4WD model). Approximately 4 months ago I had a new set of tires put on it, and in the process of replacing the tires the shop noticed that I had a bad ball joint and one of my wheel bearings was going bad. They said the ball joints were known for completely failing, but the wheel bearings usually didn't, so they recommended that the ball joint be replaced first. That is what I had them do. I haven't had the money to get the wheel bearing replaced yet. This past week it got worse to the point where I can hear it now.
At low speeds I can hear a grinding/rattling-type noise from the front drivers side (that's the side that has the bad wheel bearing). At higher speeds the grinding/rattling-type noise fades away due to road noise, but I can still hear a humming-type of noise that is a bit loader than normal - this noise just started a couple of weeks ago so I'm suspecting that this might also be related to the bad bearing.
I won't have the money to get this fixed for another 2 weeks. In order for me to have the money in 2 weeks I will need to continue working at my job 2 days a week. It's approximately 2 hours round-trip from my home to my job. Obviously with the bearing sounding significantly worse I don't want to drive it any more than I have to, but the only way I can get the money to fix it is to keep driving it back and forth to work.
Here's my question. What risks am I running by continuing to drive this? Am I running the risk of the wheel falling off while I'm driving down the freeway at 70 mph? Am I likely to experience other damaged parts in that area of the vehicle?
View 14 Replies
I noticed while driving my car there was a unusual rumble or grinding sound coming from my drivers side front wheel well. I get out and look I see a bunch of Fluid all over my wheel well. I look around turn my wheel around and see this fluids all on my rotors and suspension. Ive noticed couple weeks back the boots on the struts were ripped in two pieces from deteriorating or dry rotting (this was on both sides) and ive also been hearing some odd squeaking sound for over 15k miles every once in a while going over big bumps or train tracks. Struts go out at only 80k miles on their corolla? Yeah struts do usually lose their life around 60-80k miles but I've never seen them leak around that many miles. Is this a common issue?
View 5 Replies
At this point I'm baffled. I've been hearing a grinding/rattling noise from the driver side wheel well for a couple months now. I was positive it was being caused by a bad hub, but the problem persists. Here is what I've done so far:
replaced brake pads and rotors -- twice; once before the hub went bad and once after. The bad hub warped the driver side rotor and afterwards passenger side would not stop squealing for some reason. replaced faulty wheel hub -- The bearing was totally shot, nearly 20* of play in it, should be totally rigid replaced faulty CV axle -- I suspect vibration from the bad hub destroyed the outboard CV joint, making popping/grinding noise while turning or going over bumps filled front differential -- it was a bit low on gear oil The grinding/rattling noise shows up when driving at freeway speed (around 55mph) and gets more pronounced as speed increases. The truck does not do this under acceleration but after speeding up, the rattling is the worst at light throttle (around 2k-2.5k RPM, in 4th gear/overdrive above 55mph).
I noticed that if I shift into neutral at freeway speed, the noise continues until the truck decelerates.
So at this point my thoughts are that it could be a bad differential, but I doubt it because the noise is almost imperceptible in the passenger seat. It could be a bad differential bearing on the drivers side (sounds like a worn out bearing to me). It could be any number of things in the transfer case or transmission.
View 5 Replies
I have a 1996 Honda Accord (automatic) with just over 149,000 miles. In the 5 years since I've owned it it's required little more than some new spark plugs and tune up. I currently drive about 30 miles a week, but starting tomorrow I'll be driving much, much more to a new job. Living in Chicago with awful potholes, salt, and traffic, I'm concerned about what may happen in the near future...
I've been getting a grinding noise on the front driver side for years and have never fixed it and never noticed a change...I know it's the tie rod ends/ball joints. I've been warned that the wheel could come off, and as much as I believe them and don't want this to happen, nothing has ever happened. Is this something to do since there has been no change in symptoms or car performance in a couple years?
Other than that, any tips for keeping the car in good, working order? I do oil changes, but are they really necessary every 3000 miles? I have to make it last as long as possible and actually love the car anyway!
View 9 Replies
I noticed a pool of very clear oil on my garage floor. Looking under the truck I can see the lower control arm on the front drivers side covered in fresh oil. It looks like it's the shock absorber leaking. I just rolled over the 4,000 mile mark. I'm dreading taking it in to my nearby dealer. This is most likely a week long fix with how they operate. 2014 FX2...
View 2 Replies
I drive a '96 Infiniti I30, and recently the driver's side front wheel has started making a mysterious noise. It's not a grinding but a clicking/clanking noise. It's only present when I'm turning and accelerating. If I let off the gas it disappears. The other strange thing is that i can feel it in the gas pedal. I looked at some other discussions and the only thing that was similar was a bad CV joint. One last thing, if it is the CV joint how soon should i get it replaced?
View 7 Replies
A year ago I heard occasional metal grinding noise coming from the front, sounding like front driver side. Sounded like CV joints that I heard before. The mechanic said it's transfer case/transmission problem, so I replaced the transmission but the noise came back a few days later. The mechanic said to drive it for a while and the noise may go away, if getting worse he can fix it since it has 2-year warranty.
Now a year later the noise becomes predicable and easily reproducible, I went back and asked them to check. They said it may be passenger side axle. I am feeling being manipulated.
View 1 Replies
My wife's car has a grinding type noise (like a key being burnished on a grinding wheel, but lower in pitch). We've had our regular mechanic check the braking system and he finds no irregularities and also says that he didn't see any loose items underneath the engine area. The sound wasn't one of the ones on your excellent 'noises' list, however. The noise comes from the driver side at the front of the car. The car is 2002 Honda Accord LX with 135,000 miles on it. The transmission was replaced under warranty at 70,000 miles.
View 4 Replies
I've been hearing a rhythmic, metallic ringy grinding noise coming from the driver side front end of the car that seems to be in time with wheel rotation. It happens between 5 and 40mph, worsens while the steering wheel is turned even the slightest to the right, goes away completely during left turns, reduces and becomes intermittent above 45mph, and between 0 and 5mph, as I turn the wheel to the right from any position, I hear squeaking. I recently had the front control arm, ball joints and struts replaced. It has 140k miles. What could it be?
View 4 Replies
