Ford F-150 (2009-2014) :: 2010 - Shudder Downshifting From 2nd To 1st When Stopping
Oct 14, 2012
2010 F150 5.4, 6 speed... I am fast approaching the end for the factory 60,000 mile drive line warranty. I have had the slow speed 0-2 miles per hour shudder since 3,000 miles. The shudder downshifting from 2nd to 1st when stopping. As well as the highway shudder when gradually accelerating above 55 mph (empty and loaded)
The dealer that I purchased the truck from has driven with me several times and experienced the problems. They reflashed the computer at 5,000 miles. it made the shudder frequency double. i.e., twice as rapid. Reflashed again with no change.
I finally called Ford Motor Company, and they were surprised that I had not filed a complaint earlier. They followed up with the dealer.....who's service dept opted not to work on the vehicle again. I am now working with another dealer, and will be starting from scratch.
Long story short. I see that some have replaced torque converters, transmissions, clutch plates, valve bodies, and on and on....
View 1 Replies
Advertisement
Just pick up a 2010 FX4 with the 5.4. Noticed at idle with the A/C on 75% of the time my truck is shuddering at idle. If i turn the A/C off it goes away. Common sense is that i know the the A/C draws a lot from the engine but have a shudder like that? The P/O's ESP transferred to me so i can take it in if need be.
View 13 Replies
My 2009 downshifts hard between 2nd and 1rst gear. Real distinct when stopping at a stop sign. I have 81,000 on it. I looked at older forum's and they said flashing the computer would assist. Just curious if it works for a vehicle with that many miles on it, or if it may be a more serious problem.
View 5 Replies
Well I have 8000 miles on my 12 Eco now and it has been the best vehicle I have ever owned but it has always shifted rough, Mainly into 3rd gear but you could always feel it downshifting when rolling up to a stop sign also, I just assumed it was the way it was suppose to be. This morning I was driving it and noticed it was shifting very nice and smooth, no downshift braking or the other little issues.
I also noticed the the select shift was turned off (the numbers on the dash 1-6) if you push the + button on the shifter you can turn them off, I have had it turned on since I bought the truck because I kind of liked the display but anyway with the select shift turned off the transmission shifts very nice, I turned it back on and the rough shifting returned, Try it on yours to see if it changes.
View 5 Replies
Just turned 17K miles on the truck in my sig, it's a 2wd SuperCab I use for work since day one. I admit this truck get worked hard daily, I do a lot of stopping in hilly terrain. I always have 400-800 lbs of tools and gear in the box. But are the brakes really showing signs of wear already?
Just started about a week ago, when I slow to a stop at low speed, example parking lot, drive-through etc... I get a screech. The brake feel is still smooth and not grinding so I'm snowed. A previous truck 2008 Nissan Frontier Crew Cab 4x4 worked as equally hard from day one of its life went 40k miles on OE pads/ rotors, I'm hoping my 1/2 ton F-150 can best that at the very least. Had an '05 Cummins Diesel worked probably harder that went more than 80k without so much as a peep from the pads.
View 1 Replies
Been suffering some take off shudder as well as the 55mph shudder and finally took the truck into the dealer who informed me it is throwing a couple of misfire codes (no CEL). Quoted for spark plugs. Looking around the boards, seems a lot of people are seeing premature wear on the ecoboost plugs and have had success regapping or replacing. Any words from 5.0L owners? What are the odds they just need regapped? I'll probably just replace them anyway, but its a good discussion. Also are they are simple to replace as it looks- just pop the coil packs off and they are there in the valve covers?
View 14 Replies
I have notice maybe a dozen times in the last few weeks that my 2013 5.0 Screw downshifts at odd times. It usually occurs while coasting around 35-40 mph (in 4th gear and downshifts to 2nd gear) or around 50 mph (in 5th gear and downshifts to 3rd gear). Obviously when this occurs, the rpms jump and when I get into the gas, the truck takes a few seconds to accelerate because it first must shift into the next higher gear. What is causing this?
View 2 Replies
I bought a 2011 F-150 a year ago. Today was I driving my truck like usual and for some odd reason, it revved up to 3500 and then my truck shooked like I hit a big pump. I'm debating whether I have a faulty transmission or something. I barely touched the foot pedal. I wasn't evening barely putting any pressure on the accelerator and for some odd reason, it revved up that high and something shook my truck. I know a little bit about vehicles, my transmissions are not my thing. I'm gonna' take it in Monday morning to work.
View 1 Replies
Extended cab ecoboost 2x4. Shudders as I come to a stop while in 1st gear. Feels like it's something to do with the transmission. Haven't taken it in yet. Not towing/hauling.
View 3 Replies
New start for an old problem. 2010, F-150, 5.4, 5.5' bed. Truck is new to me, used 105K miles. Love the truck, got it to tow TT I was having trouble towing with a shorter wheel base vehicle. Has HD towing package, tows great, good power, stable. First trip out with the TT the ole Shudder in 2nd gear low speed reared it's ugly head. I did do the slip joint re-lube with Ford wonder grease.
View 7 Replies
In june of 2014 I purchased a 2012 F150 Harley Edition with the 6.2 for my wife to use as a daily driver. I told her that she could have any vehicle she wanted and she chose the White Harley Truck.
It is a Ford Certified Pre Owned and we took delivery with about 30,000 miles on the odometer.
From the test drive in June 2014 until today the truck has had two distinct issues with the rear end and suspension:
1. After coming to a normal stop (at a light) when you start to accelerate (on green) there is a distinct thunk that is heard and felt. Having owned other vehicles with a slip yoke drive shaft I knew right away that the slip yoke needed to be cleaned and lubricated and that is how the dealer repaired this issue. The repair lasted about 10,000 miles and the thunk started again recently.
2. Also after coming to a normal stop and then accelerating there is a vibration felt until the mass of the truck is moving along at about 20 MPH. It's not a vibration like a wheel/tire is out of balance it's more like the whole vehicle is shaking similar to the Space Shuttle Experience ride at the Kennedy Space Center. The shudder is severe enough that my elderly neighbors asked if the truck "was going to make it without falling apart" when my wife and I took them to dinner one evening. The Shudder is exponentially worse when towing any kind of trailer. I have a tandem axle car hauler to haul a 1992 Jeep YJ to various events and the whole setup might weigh 5000 LBS max which is well under the tow capacity of the truck. To say the shaking is violent is putting it lightly.
When I took it in for service, the dealer told me that it was my fault for riding around with the locking differential locked. I told them nice try and that I know what a locking diff is and how to use it because I have two of them in my Jeep. I then took the service advisor for a ride, made him verify the diff is off and demonstrated the problem without even leaving the parking lot. At that point he acknowledged the condition I left the vehicle with him again. The repair the dealer made was to change the rear differential fluid and called me to say the truck was ready.
I drove back to the dealer again (35 minutes in light traffic) where I was presented with the vehicle. I didn't have to leave the lot before I knew it still was not fixed and pulled back into the service lane. I was greeted by the advisor who then proceeded to tell me it was "characteristic of the vehicle." I was completely frustrated and took my truck with it's "characteristic" shudder home.
View 11 Replies
Been doing a lot of reading about shudder/vibration on the 2011+ F150's and it seems to all center around the two piece driveshaft found on the longer wheelbases and more during take-off than other times. I have an '11 5.0L 4x4/auto with the 145 wheelbase and the 1-piece aluminum driveshaft and am experiencing a shudder in 3rd gear primarily, most noticeable during light acceleration with medium load (like gently accelerating up a slight incline).
When this is occurring I can see the tach needle fluctuating just slightly (maybe 50-150rpms, just barely bouncing) but I have no check engine light and the only time I have take-off shudder is under hard acceleration which feels like axle hop (which isn't too rare on soft leaf springs with 360hp engines!).
Anyways, this 3rd gear shudder is very soft and nobody has noticed it that has rode in the truck with me, but it sure feels like the old AODE/4R70W trans would when the fluid was getting old and the TC started to shudder during "soft" lock. 5.0L? Certainly could be a miss, though power is good, mileage is great and no CEL is lit...
View 6 Replies
Well, just picked the truck up from the dealer. Had to pay for the shudder diagnosis which turned up a #8 misfire as well as lesser random misfires on the mode 6 test (no CEL) since it out of B2B warranty. Also brought up the transmission issue I have been having. Virtually every morning when I go to pull out of the driveway, when I put the truck in park it was quite violently slamming into gear, even if I let it idle long enough to drop the neutral RPM's.
Service writer was a bit baffled, but after touching base with their driveline technician, and verifying it was in no way similar to how any other F150 engages they were able to locate TSB 11-11-11 which, to me, seems primarily concerned with the harsh 1-2 and 2-3 shifting but also noted the harsh engagement.
Anyways, they squeezed me in over night and in 2 days had my parts in and installed (apparently on these trucks they have to physically get the numbers off the solenoids to be replaced as there are a couple options). 3 solenoids tested bad and were replaced under the powertrain warranty. Truck did not slam when I picked it up, looking forward to testing tomorrow morning!
The best part is that when the tech went to drive the truck in this morning to start working it not only slammed into gear for him (verifying my concern) but it also demonstrated the violent 1-2 upshift. Too bad they couldn't push a spark plug through warranty, guess I'll have to wait for my Rockauto order to come in
View 11 Replies
Was driving to Airport yesterday and out of nowhere got the flashing check engine and shudder/limp mode while trying to merge/accelerate onto the onramp (had to gun it to go around someone who decided to stop on the onramp for no reason). Let off the gas and the blinking went away. Upon leaving the airport I was accelerating again at highway speed to pass and got the blinking light and then a solid CEL. Found my way to a Autozone and got the code read. P0301 Cylinder#1 Misfire. Was suggested to change COP and plug.
Changed COP on the spot and had to drive it home to my tools to install plug. Thought maybe that since the CEL was still on solid after changing that the code needed to be cleared for the PCM to function normally again. Still have shudder when accelerating hard, so thought it might have been injectors so got cleaning service done at Goodyear. Still have the issue. Disconnected battery and performed IDLE relearn just now and it still is shuddering upon hard acceleration. Stumbled across TSB 12-6-4 which speaks to my symptoms.......I do not have the plate which in turn would imply I do not have the PCM update it references.
I have not noticed a misfire nor had an acceleration issue before so this was a surprise to come out of nowhere. I'm going to be calling my dealership in the morning.
View 14 Replies
I purchased a 2011 F150 XLT 4X4 Super Crew in early January, since then I have had it into the dealership many times to correct an annoying shudder that can be seen (looking at the steering wheel) and felt as the truck accelerates. The shudder happens around 5 kph or 3 mph and then quickly disappears as you accelerate.
This is extremely annoying in stop and go traffic and is more readily felt if driving up hill. The dealer tried shims in the differential, Installed a new rear drive shaft, U joints and the last attempt was a complete rear end all to no avail.
View 14 Replies
My son has a 2013 Fx4 crew cab 4X4 ecoboost with 8500 miles. He says in the morning for the first couple of miles while accelerating gradually the trucks shudders when shifting gears. After a few miles it goes away. Dealer says they can't do anything endless he can duplicate the condition. He went out of town for a few days and left me the truck so I'll drive it in the morning and see what it does.
View 3 Replies
I hooked up the boat and went out for a tow. I ended up getting a pretty good vibration and thought maybe it was time for balancing the trailer tires. As it turns out I needed two new tires as they were at the wear bars (cheap crappy bias ply tires) so I ended up buying 4 trailer tire radials and had them balanced.
As it turns out I have what I guess is a shudder at slow speeds and also can feel it at other speeds as well. A way to explain it is that it sort of feels like you are driving over the rumble strips on the side of the road but really small ones.
View 14 Replies
I have had my ecoboost for a couple months now. Overall I am very happy with it but I have noticed a shudder recently when accelerating and when coming to a complete stop at times. I only feel it when accelerating from a stop or when stopping completely. Kind of feels like something slips. I think I recall reading about this before on the 2011 and 2012s somewhere. What is causing this and is there a fix or is it just the way these trucks are?? I can deal with it but it is kind of annoying when driving in traffic.
View 1 Replies
I've got a 12 FX4 SC 6.5' w/Ecoboost. After 1K miles I began to develop a shudder/shake in the tranny-driveshaft passing through 1500 rpm. 4 dealers, 6 overnights and 2 escalations, I finally am told there is a design problem in the pre Jan 12 trucks. Fixed with frame mod to manufacturing process after Jan, but no solution for current owners with the problem. I replaced my 07 FX4 SC with this truck and loved it for the first 1K miles. Now I hate driving it, especially in traffic (lots of cycles through 1500 rpm).
View 5 Replies
I purchased my 2012 EB used with 35k miles on it. at about 42k I had the condensation issue happen when passing several RV's in a mountain pass. I took the truck to the dealer I purchased it from and they did the TSB13-8-1 Fix to it. I noticed right away that I had lost some power (I was very saddened).
I also have Noticed that I lost about 2.5-3 MPG. Since the work was done I still have a shudder that feels a lot like the transmission is slipping when I mash the go peddle. this does not happen every time but I would say it does happen better then 50% of the time at highway speeds trying to pass slower rigs or getting up to speed to enter the highway.
My question is has ford updated the TSB's for the 2012 EB F150's lately? I love this Truck, it is the only vehicle (besides my motorcycle) I have owned to date that I was not tired of after about 6 month's. I hope when I take the truck back to the shop next week that there is a fix that works that I get my MPG's and power back and that lets me drive it the way it should be driven.
View 14 Replies
My 2013 Lariat has just over 7,000 miles on it now. If you brake lightly at 55-60 you get a brake shutter, enough to feel it in the seat but also can see the steering wheel shake too. if you brake a little harder you don't feel the shudder much. is it possible to warp rotors in 7000 miles? 3500 of that 7000 was put on driving to Texas and back.
View 14 Replies
