Ford F-150 (2009-2014) :: 2010 F150 Cam Shaft Position Sensor
Nov 1, 2016
I have a 2010 F150 with the 5.4 V8. How many cam shaft position sensor do I have ??? I replaced one but I swear I see one one the passenger side...
View 1 RepliesI have a 2010 F150 with the 5.4 V8. How many cam shaft position sensor do I have ??? I replaced one but I swear I see one one the passenger side...
View 1 RepliesFor 2009 and 2010 f150's with the 5.4L engine, this may apply to you.
About a month back I got some odd vibrations at start-up and while driving and the following codes:
P0345 - Camshaft Position Sensor, Bank 2 (drivers side), circulation error
P0349 - Camshaft position Sensor, Bank 2 (drivers side), circulation Interim.
These codes are common in the previous generation truck for various reasons. In my case, I started trying to troubleshoot with the easiest solutions first.
Checked the battery - fully charged.
Checked/played with the alternator connection and related wiring - looked good.
Checked the oil - it was down at the half mark on the dipstick, so toped it off with synthetic oil.
Cleared the codes, and now have been driving for a month, no issues, no codes!
If these codes come up for other folks, try the easiest on the list first, before bringing to the dealer... these codes can be really hard to solve, but sometimes we can get lucky.
Where the Crank Shaft Position sensor is located on a 2004 4.2 phaeton... Dealership want 360 to install it ...
View 14 RepliesI got an f-350 drw it is sluggish on take off feels like a miss. Higher speeds when you step on it. It seems o.k I have been told it could be a crank shaft positioning sensor any in put on this. I have changed the fuel filters, cleaned the e.g.r. valve and yes it was pretty clogged,air filter seems to be good. And 1 last thing for now where would c.s.p.s. be located...
View 4 RepliesI just bought a new 2010 F150 and it came with the factory remote start with the separate key fob. Can I get one of the integrated key fobs and program it to my truck/starter? Also if that is possible where can I get one?
View 11 RepliesWhat should my idle speed be ? 2010 F150 4.6 2v, 4spd auto. Did not see anything under the hood on the stickers, maybe I missed it.
View 14 RepliesP0340 code appeared on my camry 07 said cam shaft position sensor was bad what other things can be the problem ? Also I just replaced alternator because car wouldn't start with out getting jumped once I replaced alternator it started up good for a couple of days then when I wanted to start it up it would crank then stop and crank again till it would turn on also car stereo would turn off while running and dashboard gauges would go off and would make the gauges go Dow to zero then it would go back to normal while still driving.
View 1 RepliesI have a check engine light on which diagnosed by Autozone relates to O2 Sensor, Bank 2 Sensor 1.
I realize sensor 1 is upstream before cat converter. However, I've received varying opinions as to which side is Bank 2, driver or passenger.
2010 F150 4.6 V8, produced in 5/10
Recently, my CEL came on. I had the guys at Autozone read the code and they said it was the knock sensor on bank 2. I disconnected the battery to clear it but after 100 miles or so it came back on. Idling, my engine runs as quietly as it ever has (can't tell it's running if the windows are up) so I'm hoping that the sensor has gone bad. I can't hear any knock at any speed but the re-appearance of the light has noticeably affected the engine performance. Any link that even shows where the sensor is located? If I can find it, I can replace it.
View 1 RepliesWell I read most of the 2011 manual last night to find out why I have "M" on my gearshift, & found it near the end...so we can manually shift our gears. So I normally drive in D, and I use the tow/haul switch when trailing...so under what circumstances does the normal person need to manually shift through 5 gear positions using M, and the 5-position switch?
View 7 RepliesFord Tech. told me today the reason my a/c wouldn't cool is I have a bad evap. temp. sensor and this part was "non-replaceable" the fix is a HVAC Box from ford, (price includes a h/core replacement since dash would already be out) it has 85000 miles 2010 f150 Screw 4x4.is this my only option for repairing my a/c.
View 3 RepliesI have a 2012 f150 supercrew with the eco boost. While driving down the highway my rear tire passed me. After crashing I looked at the rear end and the wheel and hub had broken off of axle. Scared the crap out of me. Would this be a warranty issue?
View 14 RepliesI have the subject truck and do my own oil changes. I see that the front end has sealed ball joints and doesn't require lubrication.
Do the universal joints on the drive shaft or any other components require lubrication? 2014 F150 XLT ....
I have 2012 F150 5.0. Was going to do some errands yesterday. Got 3 miles from my house and all of a sudden the transmission would shift from say 5th gear down to 2nd. Then it would shift up to 6th then back down to 3rd. It was shifting all over the place. I did shift it to manual it seemed to stop it a little. But then it would shift by itself again .I went directly to the nearest Ford dealer. I did not shut it off, so if there was a code there they would see it... No codes. The Ford dealer will look at it. Any thoughts?
View 7 RepliesI have a 2013 F150 SC 2wd with a 5.0 180k mileage. I have codes for all 4 banks coming up. P141 P135. I'm trying to find out which fuse works this circuit and the OM does not have it listed. What is the fuse position for thin?
View 4 RepliesI've got a bit of a weird problem with my 2012 F150 XLT Supercab w/ 5.0 and 4x4. My airbag light flashes on once ignition is in the "ON" position then turns off and back on making it code 1-1 I believe but, I cannot for the life of me, find anything about this. Also, for some reason it only happens when it's above 66 degrees outside, the temperature barely gets above that until this time of year and as soon as I take it anywhere they pull it into their shop, which is cooler than outside, and the code disappears. I would like to see if I can solve this first without doing taking it to a dealer and have a huge bill. I checked all of the cables under the seats, the fuses, the battery and the airbag module under the center console and I cannot find anything that seems loose.
View 5 RepliesI have a 2010 Toyota Corolla 1.8L, the base model.
I recently had a check engine light, VSC off light (blinking) and traction control light come on. I took it to Autozone and had a p0037 code ring up for a new Bank 1 Sensor 2 oxygen sensor (downstream). I believe I have found the correct sensor (located under car, approximately near drivers seat) and it looks simple to replace, aside from the fact that the wires go through the car body.
Can confirm that I have located the correct sensor? And if so, what is the best way to get to where the wires connect?
Is it located under the drivers seat? What should I do about the rubber grommet located under the car where the wires appear to pass through?
I purchased a new 2011 F-150 Lariat, Ecoboost, SCrew, 4x4 last weekend. I love the truck. It is very comfortable, the Ecoboost has been incredible, and the ride is very nice. I am looking forward to towing my ATVs after I hit 1000 miles.
Yet, I have one problem. I get an incredible amount of wind noise and wind whistle from what appears to be the driver's door. I read other posts about wind noises and wind whistles (e.g., bug shield), but they do do not apply to me.
I'm planning on dropping it off at the dealership this week for them to take a look at.
My 1996 ford f150 4x4.. The problem is with the front drivshaft it does not turn even when the 4x4 is not engaged. The 4x4 works and engages and disengages properly but when it is not in 4wd the front driveshaft does not spin freely..
View 1 RepliesWhere the oil pressure sensor is located on a 2013 F150 with the V8 is located?
View 3 Replies2009 F-150 FX4 SuperCrew 4X4 5.4L
My ABS and stability control lights are on. I had the codes pulled today (listed in order):
1) C1298 (Right Rear Wheel Speed Sensor Input Signal Fault)
2) C1165 (Right Rear Wheel Speed Sensor Input Circuit Failure)
3) C1963 (Stability Control Inhibit Warning)
4) C1299 (Left Rear Wheel Speed Sensor Input Signal Fault)
5) C1175 (Left Rear Wheel Speed Sensor Input Circuit Failure)
I'll ignore the stability control code for now since I'm sure it is tied to the speed sensor errors. Anyways, I decided to inspect the rear wheels and I found this sucker just hanging beneath the right rear brake caliper:
Is this a speed sensor? Where does it plug into? Diagrams would be extremely useful! I am planning on ordering 2 new sensors for each rear wheel but I don't know where to begin.