Ford F-150 (2004-2008) :: Truck Jerks Around 50 - 55 At 1100 RPMs And Again Right At 80 MPH
Jan 17, 2015
I have a 2004 f150 fx4. My truck starts to jerk around 50-55 mph at 1100 rpms and again at 80 mph.
View 3 Replies
Jan 17, 2015
Advertisement
Ford F-150 (2004-2008) :: Missing At About 1100 RPMs
My 2007 5.4 Triton developed a miss. Code came up knock sensor at first. Changed knock sensor, did plugs, and coil packs. When we did the plugs, I was in town, and all of a sudden the truck just went crazy and started running like total crap. Was smooth up until this point. Spent three days trying to figure it out, and turns out one of the plugs went bad. Had to drive it like that back to the shop, and to work a couple times if that might have caused another problem. After that was fixed it ran like a champ.
Put Accel coil packs on. I had a sulfur/gassy smell coming through the air vents, and it progressively got worse, and the truck started missing again. I put the stock coil packs back on and the smell went away, and the previous miss was back, but wasn't as bad as the Accels. Brought the Accels back and ordered a set online, and installed them. Fixed the miss for about a week. Now it's back, and really prevalent at about 1100 RPMs. I swapped each coil pack today with a good one, and no change, so I don't think it's coil packs. I'm so confused and bummed over this... is it cam phasers? The truck is at 91k miles...
Ford F-150 (2004-2008) :: 2007 - When Using Brakes The Pedal Pulsates And Truck Jerks Back And Forth
Its a 2007 f150 v6. has 55,000 miles. just got her new tires for Christmas. the truck has doing this for awhile. when you use the brakes the pedal pulsates and the truck jerks back and forth. Feels like bent rotor or something. I've been doing it about a year keeps getting worse. Last year I had the rotors turned and put new pads on got a little better. But not for long continued to get worse again. So I just bought new rotors and pads and still sucks. I thought it could be a bent rim so I just rotated the tires and still no better. Where should i go from here? calipers? something in the front end loose?
View 4 RepliesFord F-150 (2004-2008) :: Running Very Rough / Shaking At Low RPMs - Truck Died
On my way into work this morning, my 06 with the 5.4 started running very rough/shaking at low rpms. I could kick it out of overdrive and it would smooth out and seemingly be fine at higher rpms.
This worked out for a couple of miles until the truck just died on me completely. The Edge is showing po351, 352, 353......358 codes. Ignition coil Primary/Secondary circuit fault on every cylinder.
I'm thinking its unlikely that every coil failed simultaneously....computer? When I try to start the truck, it will try to hit on a cylinder or two, but will not run.
Ford F-150 (2004-2008) :: Knocking Engine At 1100 RPM
I have a 2004 F150 Lariat Supercrew 4x4 . I got a new transmission put in and a Oil change shortly after. A few weeks later I got a knocking noise. No check engine light, starts up great, No real notable problems just the noise. At Idle no noise just the usual cam phaser ticking, but once the engine is warmed up at about 1100 RPM it starts knocking like a . I took it to a few different shops one was sure it was the timing area so they replaced the timing chain, tensioner, pully. ect. Took it to a ford dealer where he didn't really look at it just said you need a new engine.
I went to another ford dealer where they said rod knock or stuck lifter but if that were the case shouldn't it knock constantly? another shop said VCT soleinods, Spark plugs. another said it could be the flex plate! I'm aware of the cam phaser diesel ticking noise they notoriously have but thats not it. I've parked it for a few years to be safe but started it weekly. I didn't intend on having it sit for so long but due to work situations and what not it has sat but now I'm on a mission to make it my daily driver again. I'm no mechanic but I'm not totally green to vehicle mechanics so ill be inspecting what i can within my limits.
YouTube video : [URL] .....
Ford F-150 (2004-2008) :: Transmission In Drive - Truck Almost Stops Accelerating At About 2000 RPMs
Well I am not sure if i have trans problem or not. If I put the trans in drive and go through the gears when the RPM's get to about 2000 the truck almost stops accelerating, until you give it much more gas, this happens in every gear. but If you push the button to take it out of overdrive and drive like that it doesn't do it.
View 1 RepliesFord 6.7L Power Stroke Diesel :: Shudder When Engine Lugged Down To 1000 - 1100 RPMs On A Hill
I purchased my 2013 F350 PSD July of 2014 and immediately noticed "the shudder" when the engine was lugged down to 1000-1100 rpms on a hill. Sounding like somewhere around the turbo belching air too. At first I was startled but learned to manually downshift to higher rpms and it will stop. Once or twice I tried accelerating out of it and it shuddered as bad as the poster who said it made the steering shudder too.
My truck has 16,000 miles and I never let the rpms drop now. So I figure I have a real problem I'm not imaging. What should I tell my dealer is the TSB or remedy ?
Golf/GTI VI :: 2010 2.5L - At Idle It Will Go Up And Down Between 1100 And 1500 RPMs
So my car started doing some weird things. at idle and only at idle it will go up and down between 1100 and 1500 rpm. No throttle input no clutch input or brake input. I do have a CEL on but when I read the code it gives me 01314 on brake electronics setting. I'm using a vchecker pro. I go into all the engine brake airbag and trans menus and do clear fault codes and this fixes it but id like to know what the actual problem is.
View 1 RepliesFord Super Duty (1999-2016) :: 2004 F350 - Truck Shakes Or Jerks Forward On Start Up
It's an 04 F350 6.8L This past winter when it was cold I would start it up and it would rock forward and bounce back as is you shifted in to park while rolling. Now that it's warmed up it won't jerk forward but the whole body shakes only at start up. As much as I like the idea of of the raw torque being so powerful the truck twists with power I don't think that's the case.
View 5 RepliesFord F-150 (2004-2008) :: Jerks While Reacceleration Around 50 Mph?
Only happens with following sequence:
Accelerate up to 50's mph, let off accelerator, then re-accelerate..especially on an incline. Get a rough jerk motion until I either let off the accelerator or accelerate hard through it. It doesn't seem to occur when the Overdrive is on. No codes are thrown.
Been to two shops, one a general shop to diag the engine and to tranny shop but neither was sure. I guess I'll have to go to the dealer but I was curious what others think of the problem.
Celica :: 2000 GTS Idles Rough / Fluctuates Between 500 And About 1100 RPMs
I have a 2000 Celica GTS that idles a little rough it has 118000 miles on it.. Fluctuates between 500 rpm and about 1100 rpm. Doesnt always do this, usually after ive been driving for a while. I also may have a rod knock, what parts would i need to fix both of these issues? Me and some friends can do the work ourselves, i just need the parts.
View 1 RepliesAccent MC (2006-11) :: Idle Speed Will Increase To Around 1100 RPMs
I noticed on 5 different occasions so far this year that my idle speed will increase to around 1100 rpms when sitting at idle for more than a few min. Last summer it did it while running a/c, and today it did it with cold weather. The rpms are usually at 550, what happens is the pcm will decide to increase idle speed for no reason at all. Start driving it, and the next time at idle it will stop doing it, a couple times it went down to 550rpms, then went back up to 1100rpms. I recently changed the spark plugs, the air filter is clean, and runs good. I have a code scanner, no pending codes. I have 53k miles. I wonder what could cause this?
View 6 RepliesFord F-150 (2004-2008) :: Bucks / Jerks In OD Around 40 MPH When Accelerating
Truck is 08' with 5.4, 3.55 gears, auto trans. 84k miles. Recently purchased from the TSA fleet trucks, so I have no clue what PM procedures were done prior to me getting it.
I noticed the following: when I get the truck into OD and then slowly decelerate (meaning I let it coast and im not braking) to about 40mph then get on the gas (normal acceleration) the truck bucks hard almost like when your spinning wheels on snow or ice and put the truck in 4wd and the front rear locks. or a limited slip rear that catches when one wheel is spinning.
if I accelerate hard the truck pushes thru it and doesn't buck as bad. I have searched this out and there are several threads about it that describe just about exactly what im talking about, the following have been brought up as possible problems:
1) bad spark plug/s and or coil/s
this seems to be the most common answer to the possible problem.
2)broke valve spring
3) bad torque convertor
So at 84k miles im thinking replacing the spark plugs would be fine to do as a PM. So coils.............should I just go ahead and replace them as well? I found them (motorcraft). does that seem right?
As far as spark plugs, I have already read the horror stories on the 04-08's breaking the plug in the head. I have also read that before 10/07 was the trucks that had the issue. my build date is 02/08. am I good to go with normal removal of the plugs? the best method I have read for removing them is spray carb cleaner down the hole and let it soak overnight and then the next day drive the truck get it nice and hot and remove them right after you park it,,,,
Ford F-150 (2004-2008) :: Bucks / Jerks Under Slight Acceleration
It just started doing it the only way I can seem to figure out how to explain it is at about 50 to 60 under slight acceleration or uphill it bucks or jerks like you have a trailer jerking. No check engine light this thing is driving me nuts... 2004 f150 5.4 ...
View 14 RepliesFord F-150 (2004-2008) :: 5.4 XLT Shudders And Jerks Going Up Inclines (big Or Small)
2004 F150 XLT 4X4, 5.4, 142,000 miles... Plugs had been changed at around 75,000 miles... Shell gas used 99% of the time.
Shudders and jerks going up inclines (big or small). Bad gas is being reported at all the local stations...Started using Sea foam and Lucas fuel line cleaner/ethanol treatment. After three tanks of that, I ran tank down till low fuel came on, kept driving, and no more shudders/jerks and ran great while low fuel light was on.
OK...decided to fill tank with Non ethanol gas this time (not Shell gas), added Sea foam and Lucas fuel line cleaner, and shakes, shudders and jerks all the time now.
Before no check engine lights came on but for once when I romped on the pedal once to blow it out, but it went off once I let off. Today going to work, entering traffic, engine light came on, blinked and stayed on. Truck now shudders and jerks all the time when I give it gas, and can only drive like Paw Paw to keep if from doing that.
Local shop ran test and #7 cylinder is not firing and two lean fuel notices. It will be Tuesday before they can check and if needed, replace coil on #7 cylinder.
I'm thinking of installing a new Fuel Pump Control Modulator as per a thread I read here, but only after they check/replace the coil. AND ALSO...turning the OD off did stop the shutters/jerks.
Ford F-150 (2004-2008) :: 2006 - Jerks / Bogs When Transmission Shifts
I have a 2006 F150 4x4. When the engine an transmission is cold it jerks/ Bogs when it shifts. After it warms up it doesn't jerk to bad sometimes but you can still notice it. Also when it shifts the RPM's drop low causing it to bog and jerk. RPM's will go from 1600 to about 800 when it shifts. It is and auto transmission. Today I wanted to try something so I pressed the button to turn the over drive off. Well it shift real good with the OD Off. Seem like with the OD Off it keeps the RPM's up a little higher so it doesn't bog and jerk. I put an Edge Programmer on it, but that didn't work. Still does the same thing with or without the programmer. I changed all my spark plug and coil packs. Truck goes great until it shifts.
View 1 RepliesFord Ranger / B-Series :: 2001 B3000 V6 Missing In 2 - 3k RPMs And Jerks?
2001 M B3000 v6 my sons truck w 122k. He is overseas and I took it to deliver a CB750 bike to my brother in law... 4oo miles away from my place.
In the middle of nowhere TX it developed a bad miss or knock, almost a shudder in the 2 to 3 k rpm range. Idles ok just below 1k runs fine at 70 mph as long as the rpm is near or over 3k.
Not sure I want to turn around and drive back the 400 with it running like crap. I will take it to Autozone and pull codes tomorrow a.m. but what should I expect?
Ford Ranger / B-Series :: Truck Jerks When Hit Brakes In The Rain
I tried to explain this to a garage in January with no luck. When it is raining I hit my brakes and my truck jerks like whiplash. Softly hitting brakes doesn't do it, normally hitting them does it (only in the rain), I had some welding done after I went to the garage.... They fixed the front passenger side now it feels like it is under me and it is now doing it when I brake in reverse too... I bought it October 2012 and it was safety inspected until October 2014. Trying to decide if it is worth keeping. I want to keep it but when I go to a garage they see dollar signs. It only acts up when it's raining. And I had the welding done in January and it was fine, until I got new tires last week.
View 12 RepliesFord Super Duty (1999-2016) :: 2004 - Running Rough Both At Idle And Driving - Truck Shakes A Lot At Lower RPMs
I have a 2004 SD with 5.4 that is running pretty rough both at idle and driving. Truck shakes a lot at lower rpms. I have a scan tool and had a misfire on cylinder 4 so I replaced the coil and the plug. Also replaced the idle air control valve. Plan on replacing O2 B1 S2. (One of my codes) even after replacing the coil and plug I'm still getting misfire detected from cylinder 4??? Other codes I had were misfire detected on he first 1000 revolutions. That hasn't come back though.
View 2 RepliesFord F-150 (2004-2008) :: Misfire Under Load At 40 - 60 MPH While In OD Or At Higher RPMs At WOT
I have a 2006 Ford F150, king ranch, 4x4, super crew 135k miles. I bought the truck and shortly after noticed the miss under a load at 40-60 mph while in OD, or at higher RPMs at WOT, but never a CEL. Well 3 months went by and I couldn't take it anymore so with lots of research I decided to change the plugs. Ran seafoam through 2 tanks of fuel prior to this job to break up the carbon in hopes of none of the plugs breaking.
All 8 plugs came out with no issue and I replaced them with the Motocraft SP 515s (old ones were very nasty and brittle, most likely the original). I put copper anti seize on the end that goes through the channel in the head, however none got on the end near the electrode, and also on the threads. Put it all back together and it had the worse misfire an pretty much not drivable....flashing CEL and codes p0308, p0355, p0356. So I decided to buy 8 new coils as well, got all 8 of them on and now the truck is drivable but the miss is still there (no CEL).
Feels like maybe just one cylinder and I believe I got it pin pointed to cylinder 8. I put a vacuum gauge on it and unplugged the injectors 1 at a time and cylinder 8 is the only one that there is no change while unplugged. So I switched out the coil thinking maybe I got a bad one, still does it. My COP electrical plug has 12v Constant and also confirmed with an led it is getting signal. The injector is ticking or pulsing as i confirmed with a mechanic stethoscope. What am I missing????? Today when I get off I plan pulling the spark plug, checking for carbon tracking, check compression, check actual visual spark, and pull and clean the injector.
Ford F-150 (2004-2008) :: Tight Steering When At Low RPMs Or Not Moving
I've got an 08 F150 and the steering has gotten tight when at low rpms or when not moving. The pump's whining and laboring. Fluid is clean and full.
View 3 Replies