I have a problem transfer case 2006 f-150 , it tries to engage once in a while as I am driving and makes a terrible noise . I pulled the vacuum lines off at the hubs on each front hub and it stopped trying to engage. What the problem could be ?
View 1 RepliesLooking at another Ex but the owner says the transfer case does not engage. Says it can be locked into 4X4 by crawling under it and engaging it manually by removing a motor [Servo motor ?] Does this mean I would need a new transfer case or just the servo motor ? I know mine did the same thing last winter. It would go into 4X4 and then pop out.
View 10 RepliesI found that my transmission was low on oil but couldn't find a leak. What I did find is that the seal in the transfer case was letting trans fluid transfer into it and then it would leak out the out put seal. I purchased the new seal and gasket and repaired it myself in about 3 hours. I removed the rear drive shaft and removed the front drive shaft from the transfer case alone or you can take it out completely if you want.
Drained transfer case unplugged wiring and one vacuum line. Unbloted from trans and removed using trans jack. The bolts are not the easiest to get to. i used a 3/8 ratchet to break them loose then used a stubby 3/8 to get them out because they are around 2 inches long. Once down I had to jack up the truck to get it out from under it. I removed the old seal and installed new one cleaned everything up and installed with a new gasket.
On my 2007 f150 5.4 last week i changed out the driveshaft and it smoothed things out. This past weekend I dropped the transfer case oil and refilled it with motorcraft transfer case oil as per ford but now the front end seems to shake more than before. It just seems to come through the steering wheel but the wheel seems tight almost like a death wobble with solid front axles except obviously this truck doesn't have that. There are no leaks and I filled it up to the top fill hole with between 1.5 to 2 liters of oil until it started running out. I should also mention that when i went to check the level it was overfull on the top plug but it was that way for the last 90,000 km or so.
View 3 RepliesI've read a few posts of people trying and they say the cant be removed but I just don't believe it! I cut off some of the rubber on the with a knife and its all white plastic underneath.. I just don't believe that its actually impossible to remove this.
View 3 RepliesMy transfer case will only pull vacuum to the hubs when floor shifter is in between 4 low and 4 high. as soon as the dash light comes on for low or high it looses vacuum. Is there a switch that tells it to pull vacuum? Any good breakdown of the transfer case?
View 6 RepliesTruck is an 03 F350 with the 6.0. It sometimes sounds like the shift motor on the transfer case is trying to engage. It has the vacuum system which is blocked off. Warn aftermarket hubs. Switch on the dash with 2wd, 4wd and 4 low.
It's kind of an off and on thing. Try to engage for a few or more seconds then nothing for awhile then repeat. It sounds like it's at the transfer case. It could very well be coming from firewall/engine bay area as well. Is there anything between the dash switch and the motor?
97 F150 4x4 5.4L ... Just put this truck back on the road after being parked since 2008. While driving at 45 mph, transfer case engaged and is locked in 4wd lo. I did notice a pop about a minute after I started the truck. Drove approx. 5 miles. Transfer case engaged and chirped the back tires, slowed speed to about 5mph. Having it towed home. I'm thinking shift motor???
View 14 RepliesI am completely stumped. 4.0 SOHC 145k miles.
There is a clunk that is coming from the transfer case (at least thats what it sounds like) when im driving in A4wd. When i transfer it over to 4HI, the clunking goes away. The clunk happens on acceleration AND deceleration. I have replaced wheel hubs, upper control arms, stabilizer end links....
Checked every other piece of rubber or bushing or connection or CV joint under that thing and can not figure it out.
Also, I just replaced the transfer case control motor and the clunk is still there. Its worth noting that I am able to switch between A4wd, 4HI, and 4LO with no problems at all. I am getting ready to drive this thing into the river.....
I've got sort of a howl going on, was thinking rear end, but when i jacked up the wheels and spun the driveshaft the noise seemed to come from the transfer case area. I haven't had a chance to check the fluid yet, could it be a bearing in the t-case? Its only when i'm on the gas if i let off its gone. 2001 f150 super crew 4x4
View 4 RepliesThe transfer case on my 2004 F350 6.0L 4WD DRW, 230K miles, just blew to pieces Sunday night. See images below. What could cause this?
I just had the front drive shaft rebuilt with new universals and ball. It was making a metallic squealing noise after this.
I noticed that the front drive shaft did not spin freely when parked in nuetral and set for 2WD. I thought the front drive shaft would only engage when in 4WD.
I bought a 2010 f150 from the company I work for.... It had a blown front diff, when I bought it, I just put a complete front diff assembly and front drive shaft on it. Thought I was golden, but when I accelerate fast there is a slipping/ snapping noise which sounds like it's coming from transfer case area... Accelerate slow and steady up to highway speeds it doesn't happen. This problem only happens in four wheel drive.... what this could be!???
View 4 RepliesThe Touareg has been a great family car for last 6 years, no issues with it at all until a few months ago, when the hanger bearing or drive chaft bearing went out with only 45k miles. No loger under warranty so $500 later and all was back to normal, until last week when the car started developing a humming noise above 40 mph. Had the local shop look into it, they put the car on the lift with it in gear and seems the noise is coming from the transfer case, i search the site and i have a few questions. Is there a recall on the transfer case?
How much should i expect to pay for a new transfer case? Is this a known problem with these cars like the drive shaft bearing? Car is a 06 with a 6 cyl, still under 50k milles im not sure if i should get it fixed or trade it for a new car
I bought a 2000 Ex PSD 4x4 in september. I have refreshed the suspension in the last 4 months; leafs, shocks, etc. I developed a vibration over 50mph after I installed the suspension and have been chasing it since.
I have replaced the U Joints, professionally balanced and lubed driveshaft twice, adjusted driveshaft angle to less than 1*, replaced the flanges for the TC output and the driveshaft companion flange. I have not touched the diff, but there is no decernable play in the pinion or leaks. Also, I removed the rear housing of the TC and replaced the output needle bearing and seal 2 weeks ago.
The output of the TC still has 1/4" play and a clicking noise coming just forward of the chain section of the TC. I assume the play is coming from other bearings on the main shaft in the TC.
I am about to purchase a remanufactured TC, but before I do, I need a reality check. Is it possible there is damage to the output bearing of the Transmission or something else?
I don't want to buy a TC to put in and experience a TC failure again in a short time. It doesn't make sense to me that there would still be so much play after changing the output shaft needle bearing of the TC if the TC main shaft is supported not just from the TC bearings but the output of the transmission unless there was possible play in the output of the transmission.
I'm in the process of changing my shift motor on my 04 f350. I can't get it off because of a broken bolt. The previous owner must have done this before, and snapped the head and some of the shaft off, so it's basically an alignment pin that's recessed into the hole on the motor. For some reason it's holding the motor on, even though I don't think the hole is threaded. Any way to get it off. I'm thinking that taking a MAP gas torch to the casting on the motor may be my best bet.
View 8 RepliesI just replaced the transfer case BW 4405. And I noticed that the 2 sensors (front drive shaft and rear drive shaft) are bad. What is the name of these two sensors? I'm looking for a brand new ones...
View 13 RepliesWhere/how to check the ATF in the transfer case? I found the lower drain bolt,but I don't see anything up higher that looks like a fill hole.
'91 Aerostar 4.0L AWD
2003 ex 6.0 limited....300000 miles ...Automatic.Merry Christmas to all.My Transfer case will not shift into 4wd . Dash light for 4wd high and low works .I get no power to transfer case 2pin connector when key turned on.Also fuses 19,27,31,33,34,45,111 are all good when checked with meter.I also swapped 2 relays in engine compartment and no change.4 WD Switch on dash has power on Green/red wire I think it is for dash light and not for operation.
View 13 RepliesSwapped out my transfer case since mine was detonated and now my tranny is running hotter? Drove in town for about 10-15 minutes and noticed my temps climbing and once it got to 180 it felt like it was slipping when moving from a full stop. i went home and parked it. Checked my fluid level and it looked a little low so topped it off while running and went through gears to make sure it was good. Drove again and it still went up to 180 in 10-15 minutes in town driving. Before we swapped the transfer case it was driving fine and went on a road trip 6 hour drive and felt fine. I bought the excursion and it supposedly had a new tranny in it.
View 14 RepliesSo long story short I have a 92 Aerostar AWD which I'm pretty sure had the transfer case recall done (97V204000 1992 FORD AEROSTAR Recalls) it has the aluminum driveshaft but a couple of years ago the transfer case cracked and I replaced it with a "New OEM" transfer case off eBay. Fast forward to the present and my van has a strong vibration at 60+ my transmission guy says it all looks good so the vibration has to be from one of the driveshafts. My thought is that I may have got a transfer case without the recall done on it and its warped my driveshaft. I don't really know thats possible or what I could do about it if that was the case.
View 8 RepliesI bought a new to me 03 explorer 4.6 tow package XLT 136000mi. Rebuilt aamco trans with 10k on it. Been checking it over before i put it on the road.. No 4x4 but the button lites work and i got into low range once. (Had a hell of a time getting back to high but eventually it did). Question is if there is 12v at the brown wire on the TC the case should be fully locked? I figure when i check it if there is not 12v at the brown wire in 4x4 high i could apply 12v directly with a jumper wire to see if the case locks to 4x4. Am I correct?
View 2 Replies