Ford F-150 (2004-2008) :: Switch 4 Wheel Drive To 4 Low Position - Not Shifting Into 4 High Or Low?
Jun 12, 2015
I made a big mistake, I was cleaning out my truck and accidentally switched my 4 wheel drive to the 4 low position. Not knowing this I started the truck and just drove it all day. Then I noticed my mistake and now the truck will not shift into either 4 high or 4 low!
The truck drives just fine, I feel no pull when I turn to the left or right so it seems that it never did any shifting into 4 high or 4 low, so I'm looking for recommendations on maybe how to fix?
View 3 Replies
Advertisement
My truck makes a noise that kinda sounds like i run over a rumble strip on side of the road when truck shifts down from OD to Drive.. only last for a second, sounds like it coming from under truck and not steering or wheel area... Plan on taking truck to tranny shop..
View 6 Replies
2002 F150 XL... My heat & AC work fine, but the only position the fan selector switch will actually blow any air is on high. Bought an OEM replacement switch and installed it but the issue still exists.
View 4 Replies
I have read through the folders and many websites on 4x4 problems. My problem has to deal with my four wheel drive not wanting to engage. It has nothing to do with the front end or solenoids. When I put it into 4x4, hi or low it will not send any power to my transfer case motor. It wont even illuminate any lights on the selector switch. I have checked all fuses and replaced any relays that have to do with the 4x4. Where I should go with this?
View 7 Replies
Last night our prius started making a mechanical sound when we shift into forward or reverse.
View 7 Replies
I have a 2006 F150 4x4 5.4L 43000mi. My four wheel drive is not working. I have the dash mounted switch to switch it into 4x4 Hi 4x4 Low. When I put the switch into 4x4 Hi nothing happens. 4x4 does not engage, and the 4x4 Hi light on the dash does not illuminate. I get the same symptom when the switch is placed into 4x4 Low. I have checked all of the 4x4 fuses and they are ok. I checked all of the vacuum lines to the hubs and they appear to be intact. What I should check next? What would cause this?
View 14 Replies
I have a 2005 F-150 with ESOF. When I turn the switch to 4x4 or 4low the lights on the dash will turn on but the front tires will not turn. I checked all the fuses and they were good. I'm not very familiar with this 4x4 system, what the issue is or on how to fix it?
View 3 Replies
When I position the switch into 4x4 High or 4x4 Low the dash lights do not come on. Also, I have a vacuum leak at both hubs.
I tested the vacuum lines from the ESOF solenoid (or whatever it's called, the box on the fender where the vacuum lines originate) and I don't have any leaks in the lines. I put the Mighty Vac straight to the back of the hubs and I definitely have leaks at both hubs.
So, why am I not getting the light on the dash, and why do I have leaks at the hubs? FWIW, I replaced both wheel hub assemblies in March, and everything worked fine at that time. I'm hoping the yellow o-rings are still good. Is there a chance I lost torque on the four bolts behind the hubs causing a failed seal? Is there a seal on the outside of the hubs that could've failed?
View 14 Replies
I have a 07 f150 and while driving I have a vibration only in 4wheel drive high but not a bad one but when I take my foot off the throttle it gets worse as well as a rumbling sound!! this is only after a 6" lift was installed it seems and I have replaced both front drive shaft u joints thinking that was the problem but didn't solve the problem....
View 2 Replies
(2004 f150 S.Crew 4x4) I noticed that my 4 wheel drive is not working. The front hubs won't lock in. The transfer case will go into 4 low but the hubs still won't lock in.
Anyway, I have pulled vacuum on both actuators and one of them won't hold. It's obviously bad, but is that why I don't have 4x4? It seems to me like it is not...
When I pull a vacuum on the actuator that does hold, it disengages the hub from the driveshaft allowing free-wheeling. Correct me if I'm wrong, but when the truck is running in 2wd, vacuum must flow to the actuators preventing the hubs from engaging? The actuator on the bad side is locked 'in' so the driveshaft always turns.
According to my train of thought, since the actuator has failed in the 'locked in' position, I should still have 4x4- What am I missing?
View 2 Replies
I have a 2008 f250 with 6.4. Was sitting my truck with key on and motor off listening to radio on lunch and my wipers came on by themselves. Switch was in off position and we're in slow speed. If I turn switch they wouldn't change speed til high position. Turned key off and back on and they came on still. Pulled 30 amp fuse in battery junction box to shut them off.
View 3 Replies
My selector switch does not light up when engaging four wheel drive on my 98 f150,could this be my GEM module gone bad ?
View 6 Replies
I have a 1998 F-150 and when shifting into 4 wheel drive (manual floor mount shifter) the drive shaft from the transfer case turns but the wheels do not engage.
Looking for a diagram of how the axle works?
View 3 Replies
Well I read most of the 2011 manual last night to find out why I have "M" on my gearshift, & found it near the end...so we can manually shift our gears. So I normally drive in D, and I use the tow/haul switch when trailing...so under what circumstances does the normal person need to manually shift through 5 gear positions using M, and the 5-position switch?
View 7 Replies
Do a 2004 Saturn view front wheel drive transmission will fit in place of an all wheel drive...
View 1 Replies
I have a 2001 f250 7.3 powerstroke it is an automatic. It has the switch on the dash to engage the 4 wheel drive. When I turn the switch nothing happens.. no lights come on or anything. it has warren locking hubs. What my problem is???
View 2 Replies
I have the ESOF in a 2000 Excursion. I went to use 4X4 high and it would not give me 4 wheel drive. light on dash said 4X4 but no 4 wheel drive. I was in snow and only rear wheels spun. When switch is placed in 4X4 low I get 4 wheel drive.
View 1 Replies
I own an 08 Rx350 at 70k miles now. This is my first car ever; my parents bought it brand new and gave to me as gift after I graduated from college. I try to take good care of it; whatever the dealership tells me to replace, I replace it. I follow the maintenance schedule and owners guide to a T. I never really paid attention when my parents drove this car...but I don't know why my car vibrates when I get maybe above 60 mph and try to apply the brake. I do not brake hard and now I pretty much avoid applying brake and just let it glide. Is this normal? Whenever I visit the dealership they do a complete check up. All the check up results are normal;nothing wrong with tire trims, brake pads, suspension etc.
View 9 Replies
I keep getting this message on information center " service for wheel drive switch", I own a 95 jeep grd chero. 4.0.. Can I do this one myself or do I need a pro in shop to service? Where to start.
View 9 Replies
Alright so a friend of mine has a Ford Explore with the little switch on the dash for auto 4 wheel, high 4 wheel, and low 4 wheel. When it is in Auto it has no issues drives fine and good. As soon as you turn it to 4 wheels high and start to go all you get is a loud clunking noise constantly. Another friend had a similair issue with an AWD explorer that we just pulled the front drive shaft and it seemed to solve the issue. How would I test the driveshaft to see if that's the issue.
View 2 Replies
2008 F350 when I switch the 4x4 to 4 Hi or low the cluster light doesnt indicate it has switched into 4x4 probably 50% of the time it works 50 it doesnt! I have pulled the transfer case shift motor off tested and working installed a new 4x4 switch, checked the relays it has been to Ford two times last week and once they pulled an error code that says (switch, 4x4 module or wiring problem)! Ford did reprogram the 4x4 module just to see if it would fix it and no change all this leads me to believe its the 4x4 module!?
View 14 Replies