Ford F-150 (2004-2008) :: Stumbling / Running Rough - Check Engine Light Is Either On Steady Or Flashing
Apr 17, 2014
Got an 07 Screw with only 50,000 miles. Yesterday, wife drove it home from work and said it would only do 45mph and didn't sound good. No warning lights were on, she said. I test drove it in the evening and it ran totally fine. Today, she drives it to work and said it ran real rough and "Check Engine" light was on. I picked it up from her work and it idles very rough and slow, and once you hit about 2000 rpm, it runs decent, maybe even normal. Below that, it stumbles and engine doesn't sound right. "Check Engine" light is either ON steady, or flashing. I don't have a code reader, so its likely going to the Ford Dealer Monday. Is there any way to read the code without a reader?
View 11 Replies
Advertisement
2005 F-150 4.6L 2WD, 268,000 miles....
Recently I got a flashing 'Check Engine' light and a rough running engine (along with a tapping noise) when I was passing someone (and pulling a trailer). I retrieved codes 300, 304, & 305. I can't swear to it, but I think the tapping noise started at the same time as the coil problem.
I replaced coils #4 & #5 (later that same day) and the engine smoothed back out but the tapping noise is still hanging around. The noise speeds up at higher RPM's and doesn't go away if I shift into neutral. Oil level and pressure are fine and I only use Motorcraft 5W-20 and Motorcraft filters (and change the oil every 5K miles).
Not sure if this is relevant: I think I have bad valve guide seals (blue smoke after long idles) but no other problems that I am aware of. It sort of sounds like a lifter, but is there a good way to pin it down? Is it possible that this tapping is related to the bad coils?
View 5 Replies
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 Replies
I have a 2012 Ford Fusion SEL. In late December, the check engine light came on (steady, not flashing). I took it to a local mechanic, as the nearest Ford dealership is a 45-minute drive away. He said an evap code came up indicating that there was a problem with the vent valve solenoid, not the capless fuel filler. However, he did not have the diagnostics to research it further.
As there have been problems with the vent valve solenoid, including a recall (for which we do not qualify), my husband bought and installed the part on Jan. 7. We both drove it several times since then, and the check engine light stayed off. But when I drove it today (Jan. 11), the light was back on.
View 19 Replies
I have a 2006 Sonata 6-cyl with 124K miles on it that also has an engine light that stays on but the car runs fine with the solid light. Only on a COLD start, usually first thing in the morning, is when the engine light starts to flash and the car runs very rough. When the engine light flashes and the car is shut off for about 5 seconds and immediately restarted,the engine light again stays solid and the car runs fine. I have had this issue for approx 2 years.
One mechanic says the code that always comes up is "P0306" (cyl 6 misfire) when the engine light stays on solid. When the light flashes and the computer is read,it gives EIGHT separate codes and all are cylinder misfires (P0300-multiple misfires and then P0301 thru P0306 for each cylinder misfire).
One dealer in the Phoenix,AZ area says my #6 cylinder valve is sticking and I need a full valve job because they supposedly did a compression test on all cylinders (which I doubt they did). I have spent upwards of $2000.00 already at both the dealer and 2 other mechanics to try and find the issue. I feel it is an electrical problem (sensor or computer itself) because one would think the car should run rough ALL the time if it was the actual valve sticking,but it runs fine when the engine light stays solid. I am running out of time because my emission test is due in 4 months. I do not trust this dealer to diagnose this issue; they have proven to me they are incompetent and just want me to pay through the nose for possible fixes until they finally just happen to stumble upon the correct problem.
View 4 Replies
2006 F150 Triton 5.4 Motor... It's been over a months journey with fixing this truck....
How it started: had an oil change, a while back, on long drive after, check engine light started flashing as I accelerated up hill so I pulled over and in a while it was ok, but couldn't get on the gas too much, or it would cause that flashy light thing.
So fast forward to now, after driving it with an intermittent miss for a while, was driving it to work and the miss became a shudder, and she stopped going over 30-40, and runs extremely rough.
Steady but loud idle.
Replaced all plugs with motocraft plugs and new coils all around. No change.
Finally hooked it up to a computer and got random misfires, now it's saying
P0174 bank 2 too lean,
But it's bank ONE that's the only side misfiring.
Here are the freeze frame details:
Frame 1 Mod $00
MIL Status Off
Troub Code P0174
Abslt TPS 24.3%
Eng speed 1665
Baro PRS 71 kpa
Calc Load 100%
[Code].....
View 3 Replies
I just had my 04 5.4l engine rebuilt. Ive driven it about 500 mi and it started running rough at a stoplight. I tapped the accelerator and it started running good again but service engine light came on. I pulled the codes and they were P0022, PO345, P0340,and P0430. It has done this several times now. Everything was replaced including the phasers, except for the camshaft sensors. Could they cause this problem?
View 3 Replies
I have a 2004 VW Touareg with 116K miles. Yesterday the check engine light came on and she is running very rough at low RPMs. The manual tells me that there is either a problem with the exahust manifold or an O2 sensor is bad. It feels as if she is struggling for air. When you start the vehicle the check engine light flashes then stays on in the cluster. What can I expect when I take it in to the dealership? Is there anything I can check before I take it in?
View 4 Replies
So I bought an 04 3 months ago everything seemed good all deltas were good had a small leak nothing serious. I had the egr deleted then i did the mistake of flooring it 1 morning at top end and the mech is telling me threw a valve. The truck was stumbling and running ruff with white smoke. looks like cycl. 7 took a hit and shows 10 psi of compression. The injector are in working order and so are the rockers. the bill is 3500 all in for new gaskets and oil cooler head work, arp studs and labor.
View 8 Replies
I just started to have this problem yesterday. Engine light comes on and stays on. Engine shakes and truck won't go over 50 MPH. Autozone code checker came up with P0171.
Truck has about 95K miles and I had the spark plugs replaced at 75K miles.
Transmission was rebuilt at around that time also.
I only drove it to Autozone and back today to post the code and see what everyone's opinion is as to what's wrong.
Here's what the printout says : P0171 "Fuel Trim Bank One Condition"
View 6 Replies
I have a 2005 f-150 street boss with 79000 mile, and it is shooting off going down the road, and the check engine light is flashing. The first time I started it back up and it would idle fine, but the throttle wouldn't do any thing. After setting about 15 min. I started it up and it ran good. I checked the codes and it had a p2104 Throttle actuator control system forced idle. It happened again with my wife. This time when I checked the codes it had the p2104 and a p2112 throttle actuator control system stuck closed code. What could be the problem, or a troubleshooting guide I could use to try and diagnose it.
View 6 Replies
So the last couple times I got a car wash the truck started running real rough, sometimes dies, then runs fine after a few minutes. Well, the last car wash I got it did it again, but the issue didn't go away. I checked the injector plugs, cleaned and greased, no change. Validated the bowl is filling with fuel, changed fuel filter, no luck.
Sometimes it will start and idle fine, rev in neutral fine, if you come off throttle abruptly it will fall below normal idle and start stumbling with an SES light and eventually die.
I managed to get it idling good, started logging with TPro (attached) and it was throwing codes P0475 - Exhaust Pressure Control Valve, and P0705 - Transmission Range Sensor Circuit Malfunction, as well as P1211, p1249, p1316 listed as 'multiple descriptions'.
I'm assuming this is an electrical issue since it happened after washing the truck, just not sure what sensor would cause all this?
View 14 Replies
I have a 2007 F-150. Here is the story....
Last summer the truck was idling rough and seemed to be stumbling a bit. Took it to the dealership and had it diagnosed. Had a mis-fire code on cylinders 1 and 3. I was told to do the spark plugs and clean the MAF. After replacing all plugs and cleaning the MAF the truck seemed to run better but it didnt last long before it started doing the same thing. My Edge Evolution started showing misfire codes in cylinders 1 and 3 again and the truck is stumbling like crazy. Here is what i have done:
1. Swapped the plugs from cyl. 1 and 3 with cyl. 5 and 7 and the problem followed.
2. I replaced the bad plugs with new ones and i no longer get a code for those cylinders but the truck is still acting the same.
Now I am getting two codes saying the system is running rich on bank 1 and 2 and a misfire code in cylinder 4. I cleaned the K&N filter and replaced the MAF but it is still the same. The truck stumbles horribly under a load and has NO power.
History:
2007 F-150 5.4L Lariat
75K miles +/-
K&N Filter
Edge Evolution (has been kept in stock mode)
new spark plugs last summer
new MAF (this week)
New Fuel filter (two summers ago)
View 5 Replies
My 3.0 with 216k miles has developed a rough idle and it progressively got better with new parts and cleanings. On startup it revs up to 2k then back down to 600. If I let it idle for about 8 or so minutes my Check Engine Light starts flashing. If I drive about for a little bit it stops and is just fine.
While the light is flashing I get codes P1000, P0305, P0306, and P0316. Which are OBDII Monitor Testing Not Complete, Misfire detected in Cyl 5, Misfire detected in Cyl 6 and Engine Misfire Detected on Startup (First 1000 Revolutions) respectively. Any other time the truck runs like a dream. Gets 20 city and 29.5 highway.
I cleaned my Mass Air Flow, replaced my Idle Air Control, SeaFoamed throttle body and vacuum lines, brand new coil pack, new wires, new plugs, new fuel filter, I've only ever run 91 octane, Chevron with Techron goes in at every oil change and B12 every other and I just ran 3 bottles of Lucas fuel injector cleaner.
View 12 Replies
We have a 2005 Prius with 77,400 miles on it. My wife came home from a short trip yesterday saying the engine was shaking the car and the CEL was flashing. About 4 months ago we also had the CEL come on but not flash and it ran a bit rough but not as bad as it is now. I was told by our local dealer that a flashing light is worse than if the light comes on and stays on. When this happened 4 months ago at 74,000 miles the dealer said they downloaded codes P300, 303, and 304 and that I needed to replace all 4 fuel injectors.
I realize that 300 is a general misfire code and 303 is a misfire code for cylinder 3 and 304 is for cylinder 4. After reading some advice on here 4 months ago, I cleaned my MAF sensor, ran some fuel injector cleaner through a tank of fuel, replaced all 4 spark plugs, and started buying Chevron gas. The CEL stayed off and our mileage went back to normal. I thought I had solved the problem but now this after 3000+ miles. I checked all the ingitors, connections, spark plugs, and wires yesterday and all seem to be in good condition. Maybe they were right and the fuel injectors are going bad. I am at a loss as what else to do other than take it back to the dealer now and plan do that this afternoon.
View 5 Replies
My girlfriend has a 2002 F-150 with the 4.6 V8 and I was going to change the spark plugs for her. She said it started running rough and it threw a code and check engine light. She took it for a scan and they told her the number 5 plug was mis-firing. I'm fairly handy and bought a set of the recommended Motorcraft plugs from Rock Auto, AGSF32PM. It also matched the number in the owners manual so I thought I was pretty safe.
Funny thing, when I took the old ones out, they were AGSF22WM's instead. My thinking is they are a colder plug than the supposedly original equipment, but I don't think they've been changed before. They looked well used but the color was good. The truck has about 135K on it.
Long story short, and to get to the question(s), Would there be any reason the factory would have put a different plug in the engine than what is listed? Am I asking for trouble going with a hotter plug than what's been in there (pinging or timing retardation/loss of power)? Am I just overthinking the whole thing and need to put it back together and drive it?
View 9 Replies
I have a 2001 elantra 2.0 gls. It is running rough with low power and flashing engine light. It may have a bad 02 sensor but when checked for spark only the 2 and 3 cylinders were sparking. I can confirm this because when I unplugged the 1 and 4 spark plugs it made no difference in the way it was running. Next I tested the resistance on the coil packs. Both were an even 1.5 ohms. How can it be that the coil packs are good yet the plugs aren't firing? I also have moved plug wires around and have had no success.
View 8 Replies
The X has been running great, well good enough, lately with no issues. I left work the other morning, and apparently the X didn't want to wake up that early. As soon as I started it up, the check engine light came on and it was running like crap. Had a bad hesitation all the way home. It feels like it is misfiring, but only under load. It doesn't do it if I brake torque it or Rev it up. Only while driving.
The codes I am getting are in the P035x family (typed that way for future searches). P0353 and P0358 are the codes I am getting (along with 4x4 codes for the vacuum solenoid...but that's the solution to other problems not relevant to this!). Being codes for the primary circuit, I popped the hood and checked out the connectors. Both connectors are fine, and tightly connected. I did notice however that cylinders 3 and 8 have other than OEM coil packs on them. These are the only 2 cylinders with those coil packs (they are white and the other 8 cylinders have black coils).
I don't want to just throw parts at it, and I'm not getting a hard miss fire code, just the 2 above. I might try to swap the coils with other cylinders tonight and see if the codes move to those cylinders. It has run like this a few times, but never set a code, and turning it off and back on has "fixed"this in the past.
And just for complete disclosure, while looking for where I saved a password, I found notes from August last year where I pulled codes, and these two codes were present then, with a cylinder 7 hard miss fire code. I replaced the c7 coil with motorcraft cleared the codes, and P0353 and P0358 went away and I haven't seen them since. The plugs are brand new and only have about 1000 miles on them (changed them in September when repairing the misfire and I don't drive it much).
View 11 Replies
I started out with my 2000 F150 with a 5.4 V8 running rough at idle. It would idle way down slow and then rev up a little over and over. On a couple of occasions it would even die when in drive or reverse. I did finally get a Check Engine light so i put it on my diagnostic program to see what was up. Here is what I got:
P1151 Lack of HO2S21 Indicates Lean
P0171 System Too Lean Bank 1
p0174 System Too Lean Bank 2
After doing some reading up I checked all my vacuum hoses and cleaned my mass air flow sensor. I then got the same codes again after a few minutes of running. So I went to the next thing that was recommended, the upstream bank 2 O2 sensor. After changing it the truck ran fine for a couple of days, no issues. Then all of the sudden it idled a little funny again and I got a Check Engine Light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0300 Random/Multiple Misfire
I reset the light to see if I would get the same again later. Before the light came on again I filled my truck up with gas and it seemed to be running pretty good again. Then a day or so later it set the light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0136 O2 Circuit Malfunction Bank 1 Sensor 2
P0156 O2 Circuit Malfunction Bank 2 Sensor 2
P1131 Lack of Switches HO2S11 Lean
P1151 Lack of Switches HO2S21 Lean
I went ahead and drove for a few days as it had gotten really cold here and I didn't feel like messing around in my shop since it isn't heated. A couple days ago I needed gas so i filled up again. Suddenly the problem was gone again. Truck ran fine idled fine no missing or odd idling at all. That lasted a day or two before it started acting a little weird again. At that point i was down about 1/8 of a tank from full. I have read that there can be issues with the fuel pump.. I am kind of wondering if that may be it now. But I haven't had to deal with this sort of issue before so I am unsure what to check next. The truck always runs fine off idle, it only seems to have the issue when it is idling. I had reset the codes the last time and i have the light on again now. I haven't checked it yet but I am sure it is going be some combination of what i have had in the past.
I have read that the IAC valve can be an issue as well. I had a problem with mine sticking a couple years ago and when it would do it you could just tap it with a wrench and it would idle up. But it never died like it does now and it would also idle a lot slower than it does. Back then I cleaned the valve and had no more issues with it. The truck has always had times when it would act weird at idle usually after slowing down after being at highway speed. The current issue happens at all temps cold or hot.
View 10 Replies
I replaced the heater core in my truck this weekend. The only thing I was worried about was pulling the dash. The truck is a 1998 f150 with the 5.4.. Everything went fairy well and decided to replace the AT Shift cable as well. Got everything put back. Truck runs, no leaks, no antifreeze smell. After running about 20 minutes, it started idling a little rough and my check engine light came on.
The codes are p0136, p0156, p1131, and p1151. I know these are related to the OS sensors. My question is could it be as simple as I miss an electrical connection when putting the dash back in? Was thinking possibly somewhere on the passenger side under the kick plate or possibly something while hooking up the heater hoses? Maybe even a ground that didn't get connected back when putting the das back in?
View 1 Replies
So i have a 2000 ford ranger 2wd 4cyl .190k miles. My issue is the motor has a very rough/shaking idle,abs light on,and check engine light on.it also continues to blow fuses to the tail lights and dash, haha
Ive had it since it was at 40k and has been a great truck,although lately i have really neglected it.ive changed the spark plugs and new wires new timing chain. I would d love to start trouble shooting some of this stuff this weekend if the weather holds up.
View 14 Replies
