Ford F-150 (2004-2008) :: Steering Wheel Occasionally Clicks When Turning - Bad Bearing?
Sep 20, 2013
I have a 2004 F150 SCrew 4x4 with the 4.6 (260K)... My steering wheel occasionally 'clicks' when turning - It sounds and feels like a bearing is bad in the steering column.
When it happens, it feels like one in the bearing is binding- the steering wheel slightly binds, then there's a 'pop' like the ball snapped back into place. This only happens occasionally. Sometimes it will pop with every revolution of the steering wheel, other times not at all.
Originally, I thought it was a U-joint, but it seems like the noise is coming from the bottom of the column...
View 1 Replies
Advertisement
It feels like I am having a front bearing issue, when turning the steering wheel to the right I feel a slight vibration in the steering, need to know which one is going out,??? I have already replaced the passenger side twice It just seems to not tighten completely as I can still move the tire slightly while up on a jack...
View 12 Replies
I have an 08 F-150 5.4. When sitting still or moving, and turning the steering wheel to the right and only the right past center, there is a popping type noise somewhat like a screw driver down a washboard (for those who'll know what that is). I replaced the ball joints because I saw a slight amount of play, but the noise is still there.
View 12 Replies
My sister has a Camry that has a squeak in the steering wheel occasionally when you turn the wheel. She lives in another state, and so I'm only going by her description, but I'll be visiting soon.
She describes it as an intermittent squeak/groan when the wheel is turned. I think it may be plastic on plastic, but it is definitely coming from the area around the column (up by the combo switch and ignition switch area), not down by your feet, she says.
I'm not sure of the year, but it is in the 2001-2003 range, I believe. I think this is just an annoyance thing, not a mechanical problem.
View 11 Replies
I have a 2008 RX 350 and I am experiencing issues with turning the key ignition and having the steering wheel locked. It gets locked and after several attempts at jimmying the key it eventually starts. My concern is that if I keep this practice up I will damage my key. I have addressed this issue to the dealership and I was naive and trusted them with fixing the problem with my last maintenance visit. Thinking the the problem was solved I started to experience the same problem again. I was first told that it is possible the my key chains are too heavy which could of caused the problem but I lightened the load and still have this problem. I've read about this problem with other people but there doesn't seem to be a solution.
One thing I have noticed is that I tend to experience this problem during the cold weather. During warmer weathers I don't have issues with the key ignition being locked but now that it's cold I am having the problem again (not sure if this has to do with anything). Do I need to change a part out to fix this? I've also read that there can be dirt in the ignition which needs to be cleaned out. Will this work and if so how do I do clean it?
View 1 Replies
What is causing the right front wheel bearing to keep going bad on my 06 f-150 2 wheel drive....
View 1 Replies
Have a wheel bearing going south can it make the car hard to turn one direction. I dont really have any humming like a wheel bearing does. But i feel a little resistance every now and then when turning the steering right. I have sprayed the steering shaft joints and i can see that they are moving free like they should. And i have a less than 2 yr old steering rack. My truck has 103k miles on the original (to my knowledge) bearings. i didn't know if sometimes a wheel bearing could cause a hard to turn in one direction feel.
View 14 Replies
Repeat Front Hub Failures -- 2WD Try this situation -- Purchased 2006 F-150 XL with 57,000 miles. Truck built on 05/24/2006.
Sept 2011 68,621 miles -- Left front hub failure -- Wheel bearing grinding -- Done by Bell Ford in Phoenix.
2013 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2014 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2016 -- Upper & lower control arms, struts, strut mounts, springs replaced -- Quality part used -- Complete front end alignment -- Brake job front and rear.
Nov 2016 -- New performance exhaust system due to exhaust leaks.
Dec 2016 -- Failed automatic transmission -- Remanufactured FORD transmission installed w/ 36 mo warranty. Sanderson Ford gets an A+
March 16, 2017 151,000 miles -- Left front hub failure -- wheel bearing grinding! Verified by jacking up truck and spinning left front wheel -- GRIND! This is coming from down in the hub. This is a 2 wheel drive truck. Yes, you counted correctly, this will be the 4th replacement on the Left side!
NO Towing! NO Overloading! Wheels are 2006 XLT style Aluminum rims with P235/70R17 Michelin XLT M/S (Defender LTX) tires all around.
It only hauls maybe 200 to 300 pounds of electronic equipment at the max, once in a while. This is driving me crazy! I always use FORD PARTS for the HUB ASSEMBLIES. Really loosing faith, the front right hub is OEM original - NEVER CHANGED!
View 7 Replies
I just replaced my drivers side wheel bearing that was squealing pretty bad. After replacing it I now have the same noise only consistent where before it was only when I turned the wheel to the right. I noticed the teeth in the cv shaft where a little warn down when I changed the hub. Now also along with that noise I'm getting a clunking sound. Should I just change the cv shaft or is there something else I need to be looking at?
View 1 Replies
The front driver's side wheel of my 2007 Ext. Cab makes a speed-related "ticking" sound. It's usually audible but not always there. I look for rocks in the tread of my BFG All-Terrains and sometimes I find some, sometimes not. The noise seems to be independent although some of the rocks really get up in there. Sometimes its really loud and it sounds like a rock. Bearing? 4WD CV or U-Joints or whatever?
View 6 Replies
I have removed knuckle assembly and pressed out bearing hub assembly, I have the new bearing hub assembly..... I live in Iowa so there is corrosion on the knuckle assembly - I have removed enough that the new bearing assembly will go in....
My question/concern : With the corrosion removed the surface of the knuckle where the bearing will seat is not uniform all the way around. The bearing hub assembly will go in and will require pressure to do so but will the bearing last? I can buy a steering knuckle but do not want to if I don't have to.
View 2 Replies
I occasionally experience steering wheel vibration no matter what speed I'm traveling. It starts out as a small shake and eventually becomes nearly impossible to hold onto the steering wheel. On two separate occasions, the brakes have gone out.The car has passed PA state safety inspection and I have taken it to 3 different mechanics and no one can figure out what the problem is. I have had new tires and spark plugs installed, keep up with regular oil changes, etc.
2004 Toyota Corolla S, 4 cylinders, 1.81 l engine, 240,000 miles, manual transmission..
View 7 Replies
I have a 2008 Elantra with 59,000 miles. When it is warm out (70 F+), the sterering wheel makes a binding noise (squeeking noise - it is hard to describe) when turning. It doesn't do this all the time and it is much more noticeable when it is warm out. The temps are usually mild. This is a recent problem as I haven't noticed it before.
Should I be concerned about this? I want to get it checked before the 60,000 mile mark in case this is a serious issue such as rack and pinion steering problems.
View 4 Replies
I have an 2006 Super Cab that has 72,000 miles on it. Stock everything except for Magnaflow exhaust and Hankook Dyna Pro tires. Last month I noticed some weird "hang" ups with the steering when turning and it just seemed to be a bump or something while turning. I was gone on vacation last week and started the truck after a week of sitting and the steering acted like it was binding or hesitating. It almost felt like a tire was down, got out and check pressures, everything was good (high if anything and got it to the right pressures).
After driving it got no better potentially worse. I start a turn and it is fine but at a certain degree it starts to bind and seems like the power steering is not there. It does not return to normal position easily either. I have checked the fluid and it is fine, the belt is normal (and original) with no tears, or rips in it. Not sure where to start, but have a couple thoughts of power steering pump going or front end has issues? Best description of the problem is that it is a binding feel and happens both left or right turns. Have to force it like the power steering is out.
View 7 Replies
I have a bad wheel bearing but on the highway my steering wheel shakes. It is only on the highway not down residential streets. I'm pretty sure it is the driver's side wheel bearing. I already balanced my wheels and everything.
View 5 Replies
Changing wheel bearing on mk4. makes noise when i turn to the right. what side is bad? i like working on my own car but this might be out of my hands.
View 12 Replies
When you turn the steering wheel, left or right, the horn honks at random stages of turn. Nothing long, just a short honk. If you stop the wheel where the honk happened, it just honks.
View 1 Replies
I have a 04 stx f-150 4x4, had the front springs changed, shocks and struts! now when I am driving at either 43mph or 53 mph, I get vibration in steering wheel.....
View 6 Replies
I have had some play in the steering wheel of my '04 F150 screw 4x4 for a long time. Today, I replaced the outer tie rod ends in order to get rid of a squeak. While I was down there, I tried to move the inner tie rods in and out and didn't detected any movement so I figured they were still good.
Now that the new outer tie rods are in place, my squeak is much better but I am still noticing play in the steering wheel. Assuming that I checked the inner tie rods correctly and that they are indeed ok, and assuming my new outer tie rod ends are good, why would I have any play at all in the steering wheel?
View 1 Replies
I have a 2004 fx4 supercrew 4x4 , 170k miles. I bought it a few months ago and installed a 6" rough country lift and 35" tires. I noticed a little shake in the steering wheel but not too bad, just annoying. I just put on a fabtech dual steering stabilizer to remedy the problem and its much worse. What could be at fault that dual stabilizer would make it worse? I hate to just take them off, I would rather find the problem. Oh, the tires are all balanced and I had an alignment done also.
View 14 Replies
This summer, my steering rack failed, and I had it replaced with a remanufacutured steering rack. All went well, until a few weeks ago I started feeling a pulsing effect when turning, usually when turning right. On a few occasions, the shaking has become severe. It is a back-and-forth effect, about three times a second. It is bad enough that it has triggered a power steering error on two occasions. I took it to the garage who installed the rack, asking them to have a look at it, and they found nothing. Because the effect is regular, I am assuming that I am feeling the 12V power assist malfunctioning or reacting to faulty input.
View 11 Replies
