My truck starts to miss between forty and fifty mph. When you get on the gas pedal it won't do it but when you are slowly increasing speed it will start missing or maybe you can describe it as bucking. Above fifty and below the truck runs fine.
View 9 RepliesI have a 2004 150 with 165,000 miles I sometimes pull a 5 by 8 trailer. when pulling trailer in overdrive and excelorating the engone will cough several times. I took it to a mechanic and he told me that there was nothing he could do that I needed a new engine. I can pull trailer out of overdrive with no problem. don't undrstand why I need new engine....
View 3 RepliesI bought a 04 FX-4 a couple months ago with 102k on it. Brought it back to selling dealer, they replaced #1/#6 coils, its ran great till this past week. Again it has stumbled a couple times this week. It only seems to have the miss at idle (comes and goes) take off from light, within 50 feet its running like a champ again. I cleared the codes (disconnect battery)and now it seems my idle is not steady, it fluctuates. Is the idle a product of the codes?
View 2 RepliesMy sons 04 f150 started to miss then quit on him then wouldn't start so he had a buddy pull it to a neighbors I went to check it out an hr later the first time i tried to start it it started ran for 2 sec then quit tried again and it would just crank no start went back 3 hrs later with my code reader no codes but he did say check eng was on when it quit first time so i try starting started up so i headed for home, it started running rough twice on way home but seem to come out of it both times.
View 1 RepliesI have a 2004 f150 with 135000 miles. Bought it a few months ago. I notice after the truck is up to operating temperature it seems to have a slight miss, you can kind of feel it when sitting in the truck. Cant really hear it. Outside the truck I am hearing a ticking sound. I have changed the spark plugs on the passenger side, because that's where the ticking sound was coming from.
Come to find out the last spark plug in the back was finger loose. Got them changed, on that side. Still have the miss after warmed up along with the ticking. Few weeks fast forward I put all 8 new COP on. Same results. I also have changed the oil and filter both with Motorcraft. Where I could look? I also have a 1 year unlimited mile power-train warranty.
I have a 2004 F150 5.4L 2WD auto. I had the cam phasers and timing cover done at the end of 2014 and the truck was great. Back in december, I parked the truck and when I started it the next morning, there was a horrible miss. I left it parked a month or two, then tried starting it up last week. Nothing.
So I had it towed to the shop. They found the starter was bad, and the only code it was throwing was P0341... Cam sensor bank 2. I had it towed back to my house, replaced the starter and the grounds and fired it up. It had the worst miss on the planet and died shortly after being started. I replaced both cam sensors, and now it starts right up and runs... but still has a bad miss.
I used my scanner and its still throwing A P0341 code almost instantly. It sounds like a bad miss that slightly gets better when you give it gas... but its not throwing any misfire codes or anything.
We've got a 2006 F150 with a 5.4 in it. One of the new kids was told to change the spark plugs, then when I went to start the truck the next day it was missing bad. Plugged in the Ford IDS, number 7 cylinder is dead. Only codes are for that cylinder misfire, and random miss on startup. So, I double checked the kids work and it was all fine. Tried putting a new plug in, didn't work. Moved the coil to a different cylinder to see if the miss would jump, stayed on number 7.
Used a noid light to verify COP harness was working, and it was. Put a new coil on it anyway since I had one, still missing. Used noid light to verify signal going to injector for the cylinder. Signal was good, replaced the injector for the cylinder. Still misfiring. Ran a compression test and the cylinder has good compression. The threads for the plug are fine, not cross threaded or torn out. The only thing I can think is that the PCM has gone bad in a way that its firing the injector/COP, but doing so at the wrong time some how.
Every other cylinder is running fine, O2 sensors fine. PCM isn't trimming anything back to account for anything, and if it was it would do it to multiple cylinders to keep the engine balanced. Cant think of any more tests, and I don't believe there is anyway that the airflow could be restricted to only 1 cylinder, but I could be wrong. Wanna try and solve this to keep from sending it to the dealer.
Apparently yesterday (no known reason) my sons truck started to develop a miss (so it feels like to me).
2005 f150 5.4 auto 215000km 4x4 stx. No specific cylinder codes. All general codes.
P1000
P1464
P1550
P1703
P1780
None of which I can see causing the miss. No check engine lite, no other codes. Not sure what to look at next. I am starting to disconnect the coil packs one at a time and see if I can pin down the cylinder.
I have a 2005 5.4 F-150. First off it came to me on a rollback because the owner tried to replace his plugs after he noticed it missing and of course broke one off. So after I extracted the plug from #8 cylinder and installed a new plug I cranked the truck and it was idling very rough and had a terrible miss around 1200rpm. I pulled the codes and got several misfire codes and ignition coil faults on #5,6 and 7 cylinder. Popped in 3 known good coils in these 3 cylinders with no difference.
On Mode 6 on my diagnostic software you could watch the misfire count steadily increase on #7 and every now and then there would be a single misfire on #5 and 6. It also had several codes for O2 sensors biased, stuck rich on that bank. Well since it had a brand new plug and coil, I popped an injector in #7 and havent had a single misfire on it since and it also started idling alot better and all the O2 codes went away. The problem I am having now is #5, 6 and now 8 will randomly misfire, sometimes build up a steady count on one of them, sometimes just skip around between them.
The truck has brand new plugs in all 8 and new coils on this bank also. The truck has 115,000 on it and does have some cam phaser noise on the bank causing the problem, but its not too terribly bad, I have heard alot worse. My problem is something on that bank only as the passenger side bank is fine. I am wanting to say cam phaser now since this is the side with the noise. I have changed them before but have just experienced the noise, never one running like this because of it. Possibly jumped time a little?
2005 f150 5.4.
I have a slightly rough idle and can feel a miss at 1600 to 2000 RPM. Sometimes running about 65 MPH up a slight grade I can slowly press the gas pedal and the engine will begin to miss much worse, causing the truck to shake pretty bad. When it gets this bad it will slowly flash the CEL and I get a P0306 code (Cyl 6 missfire).
The truck has 148000 Miles on it and the plugs were replaced at approx 120000 by the dealer.
In the last week I have replaced the plug in cylinder 6 (looked ok) and have replaced all the COP's along with the fuel filter and the injector on #6.
I haven't been able to get it flash the CEL light or throw a code since replacing the COPs though and I am at a loss at to what to try next.
I posted a while back about my 04 5.4 having an issue at idle. I did all the normal things like replace coil, spark plug, etc etc. No change to the issue. It still acts as though it's misfiring on a cylinder and I get codes P0306 and P0316. Finally took it to ford and had a diagnostic check ran. Everything on the top end was in working order. The tech even put a known working coil on 6 and nothing changed. I was told that it's either an intake or valve issue on that cylinder. But no definite answer to problem.
Fast forward to yesterday. I got a wild hair at lunch and went out and started truck. Pulled injector plug off of 6. No change to the way it was running. I did the same for 5, 7, 8, 1, and 2. All of which made a big difference in the way it ran. It was obviously misfiring with no fuel to cylinder. This gave me the idea to swap 5 and 6 when I got home to see if the issue followed the injector from 6. I did NOT. I pulled the plug on 5 and got the obvious change in the way it ran. So there is definitely something going on at cylinder 6 that I cannot figure out.
PCM, bad intake, bad valve? I'm not rich so a trip to ford for repair is gonna have to wait. Truck seems to run fine when driving except for slight hesitation during acceleration.
Had this truck a few years now, and it has always had a slight miss/hesitation and maybe a few codes. The timing chain skipped a tooth and the truck was down for about a year. I have 4 other trucks, so it wasn't a big deal. I finally had time to put a new oil pump, chains, guides, tensioners, phasers etc. The truck actually runs very well and quiet. But, now misses far more than I remember it doing.
When driving in town constant at 25-30 mph occasionally it will loose power for a brief moment(<1 second) and then be fine, the security light on the dash turns on for a few seconds. It drives at 55-65 just fine, unless I am going up a hill or something else increasing the load.
2004 5.4 3v 2wd
CEL-
P0453 (fuel tank pressure issue)
P0351 (ignition coil a primary/secondary circuit malfunction)
P0356 (ignition coil f primary/secondary circuit malfunction)
The coil packs are new, and I have injectors on order. Also found this thing on the back of the motor, it connects to the fuel rail on the drivers side. Where it should go. I looked on my other trucks. But my other 04-4wd has a box by the battery it connects to, but mine doesn't have any of that stuff. And my 08 doesn't have anything like this at all.
And a pix of the truck in question.
1997 F150 4X4 4.6 engine with 285,000 miles
Truck was running perfect down the road, then suddenly it lost power and started missing at all RPM ranges. So i keep driving another 6 miles and then POOF the miss is gone and truck runs perfect. Couple hours later i hop back in it and its running good and then suddenly it starts missing and loosing power again except this time it never started running good again. Never did throw a CEL.
I hooked up my SCT Tuner (for my F250) to check for codes and came up with P0171 which indicated one of the banks was running lean, but no missfire codes. Did a search on here and learned the common problems(vacum leak) of that code.
Found the vacum leak at the PVC elbow, so i replaced both ends of the plastic tube.
Pulled the throttle body elbow and cleaned out the clogged up EGR ports.
Put a new air filter in and took the MAF out and cleaned it with MAF cleaner.
Put it back together and it idled way better but still ran like crap with the bad miss/sputter. Ran it down the road a few miles and came back thinking of the catalytic converter, i crawled underneath and it was glowing red. It does run and feel like the converter is stopped up but if i have a dead miss and dumping fuel wouldnt that make it glow red to or no? Still no CEL and now no codes.
Also i held the engine at about 1000 rpms where i could here the miss good and unplugged the fuel injectors one at a time to see if that made a difference. Each one i unplugged made it miss worse, so wouldnt that tell me that all 8 cylinders are firing?
And i changed the spark plugs (motorcraft) 250 miles ago.
So it still cranks and runs smooth after a cold soak overnight and then after a mile of driving or less it starts the dead miss/sputter and loss of power.
Ok, been trying to track down an odd humming noise on my 08 f150 CC 4x4, 4.6l. kind of sounds like a hub bearing going. starts around 25-30mph and never quites down.
Turning left or right to load each side of the suspension doesn't change tone or intensity of the noise, different pavements doesn't change Tone or intensity. Hubs are tight, CVs are tight, 4x4 works as it should. Cant figure this sound out and it's quite loud.
Truck shifts great from 2 to 4h to 4l and back to 2. However, at random times - any speed - usually when slowing down - I hear/feel something engage and there is usually a ratchet sound. I figured out its the 4x4 - if I switch to 4h then back to 2 quick, it stops. What the heck.
View 1 RepliesWhen I put truck in 4wd rear end starts locking up. Take out of 4wd its fine. Just put 2 quarts of fluid. They didn't have the 75-140 so I put in 85-140 was that bad. Had rear rebuilt a year ago. Mechanic said he had to put a different gear assembly because ford didn't make the original any more. Ever since this was done rear just never seemed right. Now in 4wd if I go straight it's fine but as soon as I make a turn rear locks up almost coming to a grinding stop.
View 9 RepliesI've got 200k on my Lariat. Engine was replaced 60k ago. It's in outstanding shape and is driven a lot. Suddenly this morning I start as usual and it runs about 5 seconds then stalls out. Every start, same thing. So it seems I am getting fuel pressure to start but it doesn't last.
I did replace the Fuel Pump Module within the past two years, due to corrosion of the FPM housing. At that time the truck would no start at all. Could it have gone bad already? I'm thinking this must be an electronics failure. It was perfect all day yesterday. 2004 Lariat 5.4...
I have a 2004 fx4 with a 5.4L. i have an edge performance programer and these are the codes that are coming up....
1) P0121
2) P2104
3)P2106
4)P2111
5)P2135
I have cleared these codes and reset the main computer the truck barely starts and will not accelerate...could the spark plugs be an issue...
Read a few references but nothing seems the same as what I have... 2001 Ford F150 Larite 5.4L 4 x 4
When slowing down, at speeds of 3 to 4 miles per hours truck starts to shutter. It is not an engine issue, nor a brake as it will occur with brakes on or not applied. Engine is running smooth, seems more mechanical that fuel or brake related. Shutter is not slight either.
Both CV axles, hubs, rotors and upper and lower A Frames have been replaced. Shutter was happening prior to the replacement, they were replaced as preventive maintenance. Shutter is profound enough to shake the mirrors. What it can be.
I have a 2007 F150 Lariat with a 5.4 L engine. Bought it 6 weeks ago from the original owner. Has 50,000 miles on it. He had a Ford command start installed when it was new, and received a new key FOB at that time. When I drive the vehicle, sometimes the horn will start blowing and the lights start flashing which to me, indicates the trucks security alarm is activated. The only way to make it stop, is to hit the unlock button on the key FOB. It also does it sometimes when it's not running and I open a door. Previous owner had same problem so he disconnected the horn!!?!
View 3 RepliesI took it to the dealer and they blamed the trailer. I told them that I have pulled two different trailers and it did it with both. Then he said that the trailer was not heavy enough to weigh down the springs. So now I not suppose to tow an empty trailer? Also my father in law has pulled the trailer with his Z71 with no shake and the other belongs to a neighbor with a 98 F150 with no shake. The vibration only starts above 45mph. Any clue as to what could be causing this?
View 14 Replies