Ford F-150 (2004-2008) :: Sporadic Front Brake Drag / Hard Pedal Post Front Brake Line Change
Sep 27, 2016
Had a lift done (Rough Country, after reading through these forums) on my 04 F150 Newer Body Style 4x4. Now, sometimes the pedal gets harder to push on until it won't go down at all and the brakes (only the front) start dragging. It goes away after awhile (my rotors are shot and I'm going to have to replace them after I figure out what is going on) but always comes back. The brake lines have been bled and I'm having a shop bleed them again tomorrow (that's what they said the issue was) just in case.
View 11 Replies
Advertisement
I have a 2005 F150 4x4, with just over 75K, and I have owned it from new. I am having left front brake issues. The left front brake seems to drag, but of course does not do it consistentally or after a given type of braking event. It just does it very randomly. I originally replaced the caplier pins thinking one may have been hanging up. It seemed to fix the issue for a couple months then it happened again. So doing more inquiry it seems some have had issues with the front rubber lines.
I just had both front lines replaced with OEM Ford parts and the system flushed out at a dealer. The brakes again seemed to work fine driving home from the dealer anto work today. Then on the way home it did it again, started dragging. The truck starts to feel sluggish while accelerating and slows very quickly just lifting off the gas. then when you get out you feel the wheel and it is very HOT and you can hear a heat popping sound. (First time it happened it was smoking it got so hot.) Right side seemsfine.
Since it does it so randomly I am at a loss. I can not just drop it off at the dealer and say drive it until it. I am considering having the caliper replaced, which I really considered when it was at the dealer for the hoses since I had the IWE's done at the same time, so they were off.
View 14 Replies
My 2008 ford f250 SD Powerstroke has a bad front passenger side brake rub/ dragging after offroading before off roading just rubbed a little now it drags a lot. what do i need to fix.
View 2 Replies
08' 4x4. I changed the front brake hoses because the truck felt like it was dragging a bit, when i would hit the gas from a stop, that seemed to work, I also changed the front rotors because when braking I was getting a pulsing feeling in the brake pedal. that fixed that.
Now I feel like there is still a bit of a slight drag when I'm at a stop and let off the brake. when im on level ground the truck creeps forward from a stop when letting off the brake, on the slightest incline the truck wont go forward at all.
Do the truck want to move forward on a tiny incline or no?
View 7 Replies
03 F250 7.3. I busted a brake line last week somehow, Got it replaced and fixed up, Bled that line and everything was somewhat good.
Now, when i hit the brakes hard, I have pressure. If I let off even a little, My pedal will start to sink till i apply more pressure. I am gonna fully bleed my brakes when I'm home to see if this could solve the problem.
View 7 Replies
Ive got a 2002 f250 Sd 4x4 with 93000. Im getting severe vibration from the front drivers side at highway speed. I thought it might be a warped rotor but i cant feel it in the brake pedal, when I put the brakes on. How can you tell when the hub bearing assembly is going bad? The truck doesnt pull to that side either. I can hear it, and feel it more when i'm going around highway corners. When im driving through town, I can hear a "clunk,clunk,clunk" noise coming from that side also.
View 14 Replies
How to replace a front brake line? I am having trouble getting mine off of the frame.
View 3 Replies
I have a 2000 ex v10 4x4 the brake line that goes from the front to the back has a hole in it and is rusted out. I need the part number?
View 6 Replies
this is my brothers truck 05 f-150 4x4, i put brakes front and back and flushed the system about six months ago now. the other day when he was coming home from college the front passenger tire locked up. he drove it home and i went over took it apart nothing was sticking put it back together and it was fine. now today he call it stuck again so i just pulled it apart, pads are now purple from the heat, pins are free, caliper moves i put a small piece of wood in it and had him press the brakes the caliper moved out and i pused it back in, reinstalled everything and its not stuck no more. what do you think is causing this? my uncle says it could be the abs box acting up, when he bought the truck my dad made him buy the extended warrenty but he wont pay the 100 dollar deductible because this past winter we all went out in the two foot of snow and he got stuck so i pulled him out and our dad says thats what f$ucked his brakes up so now his is pissed. so how can i fix this for him? oh it only has 42k on it
View 7 Replies
My front driver side brake line broke. It had a typical double flare fitting at the caliper but at the distribution block on the other end it had a flared fitting that would be used on a industrial hydraulic unit. I took it to the NAPA store and they told me to cut the nut off the old line and put it new line and double flare it. I did and it leaks. Do I need a special fitting on the end that goes the distribution block?
View 2 Replies
I noticed yesterday that my tire on the driver's side has rubbed a flat spot on the rubber brake hose. I bent the metal tubing so that it doesn't rub any more, but should this be of great concern? Obviously I'd hate for it to rupture, but it looks as though it's not too bad.
View 1 Replies
So I'm away from home on vacation also away from my tools. Any ways my front drivers side line busted almost causing me to crash earlier today in my 2006 F250 6.0 diesel 4x4. So basically my question is: what tools are needed to do this job? I've already picked up the part now tomorrow morning I will be changing the part...
View 2 Replies
Im working on my buddies 2005 F150 FX4. In the midst of buttoning everything up and calling it a day I happen to see fluid dripping. The OEM steel brake line had been rubbing on the steering shaft and while doing the brakes, must of busted through all of the way.
I have been to Advance and Napa at least 4 times trying to match stuff up. Nothing works from either of them.
Called Ford and talked to a parts guy who lacked general automotive knowledge and finally had to pull up there diagram to show him the correct part. He told me that part is discontinued and cannot be ordered.
It is #2264 in this diagram.
2005 Ford F-150 Front Brake Hydraulic Hose | FordParts.com
I have the factory fittings and everything to make a new line. I cannot find tube that is 5.20mm or .20". Everything I find in a roll is either 3/16 or 6mm.
The fitting is a 12mmx1.00 on the ABS brain. The caliper hose appears to be a 3/8x24. A 10mmx1.00 which is standard metric 3/16 tube nut is to big for the OEM caliper hose. A standard 3/16 flare wont seat on the caliper hose.
So it seems like what Ford did here was.... a 12mmx1.00 on a 5.20mm tube to a 3/8x24 to a caliper hose that wont seat with out 5.20mm tube.
View 1 Replies
I first heard it start about two or three weeks ago. It started when I would brake too hard. So I took a look at the brakes and the caliper pin was rusty so I loosened it up and it was fine for a day or too. Then all of a sudden it started in the front like something was grinding. Someone told me it was the transfer case. so i put in 4 wheel drive and it goes but then you really hear the grinding. How can I tell if its the transfer case or the front end where the drive shafts go into.
View 1 Replies
After a routine brake pad replacement the brake pedal hits the floor when applied with normal force. The pedal feels like a badly leaking master cylinder, but prior to the pad replacement the brake pedal was firm as a rock with no drop at all. If I pump the brakes the pedal will come up to normal height, but if I then maintain light pressure the pedal will again sink to the floor.
1. Truck was braking fine, however pad 3/4 worn
2. Replaced front calipers, rotors and pads
3. Replaced front brake feed hoses
4. Replaced rear pads
5. Started engine
6. Started bleeding from furthest point from MC a) passenger rear, b) Driver Rear, c) passenger front, d)driver front. Did it two times...
Still, brake travels all the way to the fire wall and never develops tension. Moreover, sometimes, when person pumping brake puts pressure and i open bleed, no fluid comes out. Could it be a failed master cylinder??? I tend to think it's not because 24hrs ago, the pedal felt fine and the truck was braking ok.... So much for preventive maintenance.
View 14 Replies
When coming to a hard stop and downshifting using engine braking, is it normal to have the brake pedal feel like it loses pressure to where the brake pedal pushes down further towards the floor for a split second? What causes that to occur?
View 10 Replies
I have a 2008 Prius. Had to do an 'emergency' stop. Put my foot on the brake pedal REAL hard and the car slowed way down, but not down enough. Munched the front end. Now remembering back, I didn't feel any 'chattering' from the ABS brakes. It seems like I got regen braking but never switched to the hydraulic brakes. Is that possible? Did I experience a braking failure? Or do Prius just take a lot longer to stop? I did a test stop in the rental car I have now (not a Prius or hybrid), and it gives me the ABS chatter as I would expect, with a short stopping distance.
View 5 Replies
My 2004 F 150 the rubber piece that goes on my brake pedal keeps on falling off after I put it back on looked it over today and did notice it does have a good size tear in one of the corners....Can I get a replacement one of these? all I need is the rubber that goes on the pedal....Would I have to go to the dealer for it?
View 3 Replies
What would cause the brakes on my wife's truck to be stiff and not hold?
View 14 Replies
About two weeks ago I noticed that my parking brake light was not illuminating when I enagaged the brake. Since then it sometimes comes on when I engage the brake but not always (most of the time it doesn't). I can't replicate the conditions and there doesn't appear to be a pattern of temp or time of day.It is an '04 with 146,000 miles.
View 1 Replies
I have just purchased a VW GTI 337 with 194k on the odometer. The car has a few issues, I have listed the issues by importance. The car came with a stage III ARP turbo kit installed. I just don't know if it's the stage III or stage III+. The car seems to be running okay but it seems like it's lacking the power. Meaning that I should be feeling more. Could it be that car seems to be in some sort of limp mode?
1. The car surges when I am at the low and mid pedal. But, not when I am wide open throttle. Seems like to me that the car is hesitating until I give it a lot of gas. I have changed spark plugs and coils have been replaced by VW dealer for free.
2. ABS light is on and stays on, does not blink just stays on.
3. ASR button will not work. When pressed in it will not light up or show that its activated.
4. Left brake pad or sensor is not plugged in because it's missing the connection. Looks like someone cut it off for some sort of reason.
5. A light that has a triangle with a circle surrounding it, is on. The light is in the cluster.
6. The front brake pads light is on, this is also in the cluster.
View 4 Replies
