Ford F-150 (2004-2008) :: Slight Ticking Noise - Code P0022
Aug 16, 2015
Getting code P0022, which is over retarded cam position, drivers side bank. My 2004 F150 has the 5.8 triton. I have replaced all cam phasers and tensioner a as well as the timing chains. I have also replaced both VCT solenoids. Before I was getting codes for both banks, now just the code mentioned above with a slight ticking as well. My question is this... What am I not seeing? What could be causing this?? Would it be beneficial t get the lockout kit for the phasers to always keep them open?? Seems to stall a little at very low RPM like when you are off-road.
View 1 Replies
Advertisement
My wife's 06 expedition 5.43v runs rough loud and dies. Not all the time just when it's to hot. I got a code it's p0022 cam sensor. I changed both started the rig up and heard loud rattling like metal maybe chain. It lasted for a the length of my video 1.4mins give or take then went fine, i turned the car off and back on everything seems fine. I know I got her oil done after driving. She had metal/plastic in her oil. I had all plugs done and actually i re did the 8th cylinder plug because it was miss firing and i pulled it by hand with only the socket no ratchet. I'm thinking the chain is going bad if not already bad. Only 113k miles my 04 f150 5.43v lasted 250k before motor swap...
View 7 Replies
Driving around today my cel flashed on. Checked my programmer its saying P0022 intake camshaft position timing-over-retarded bank 2. What is the culprit?
View 2 Replies
2005 f150 Lariat 4x4 5.4
Had phasers, tensioners, chains, guides, and sensors replaced. After driving the truck, it started to get a rough idle at low speeds, primarily in reverse. Changed both vct solenoids with no results. Started to get p0022 code. Changed the oil with motorcraft filter and 5w-20 twice after the work had been done, thinking it might need it. Vct's were a little varnished, but not too bad.
After a couple days of light driving, got a misfire on #3. Replaced the coil and it hasn't been back since. I am stumped at this point.
The computer show the timing to be at +13 when sitting stopped and in drive. It fluctuates a little, but not much. When the truck goes into a rough idle. The rpm's fluctuate wildly. It seems to be happening more frequently, the more I drive it.
View 3 Replies
I just bought this truck yesterday. During the test drive and everything it seemed all fine. After all the paperwork and the truck was actually mine. I noticed once it is all warmed up it seems to have a slight knock/tick? and a slight miss to it. I shot a couple videos, one up underneath where it sounds like most of the noise is coming from. Could it be an exhaust leak? Or is it something internal? Like the Cam Phasers, or a rod or something!
Here is a video around the exhaust area.
Here is up underneath the truck.
View 5 Replies
So I have an 05 Expedition (I know this is the F-150 forum, but more visibility) that is throwing a P0022 and P0345. I get these point to the cam phasers, so before I throw $450 on a phaser kit and oil pump, I want to make sure its a good fix.
I have done a lot of research on this forum and other where people have replaced their phasers and it doesn't end up fixing the issue. So I just was looking to get some tips before I endup shot gunning parts.
View 7 Replies
I have a 2007 F-150 5.4L and it started throwing codes p0012 p0022 p0345 and would knock and make popping sounds after it warmed up but I could rev it up and it would go away for the most part but would come right back when I started driving it. I have since pulled down the front cover and made sure it was in time, replaced both cam phasers, replaced both vct solenoids, and replaced both cam sensors. Same issue after doing all of that. I have searched the internet and have come up with nothing.
View 3 Replies
My 2004 V8 touareg is throwing CEL code P0022. 'A' Camshaft Position - Timing Over-Retarded (Bank 2)
What would cause this? I found that these all could be related:
- Valve timing
- OCV
- Camshaft timing gear assy
- ECM
Would any of these cause it to burn oil more quickly? What steps are taken to diagnose the whole problem?
View 6 Replies
I'm having the well known situation with P0345, P0022
Replaced both phasers, replaced cam sensor, checked timing (properly aligned), assembled back still running rough and rattling, used 10w40 oil,
Complete rebuilt engine, we did head work new seals and springs, valves are straight I had it checked out twice for assurance. New pistons, new rings, new bearings, new oil pump and seals of course. If I disconnect cam sensor Bank 2 it works fine but still runs a little rough.
- Replaced one tensioner due to gasket wear.
- I was told to check on alternator ground (it's missing I know cause it got broken and I haven't replaced that ground that goes into the engine.)
- I also was told change oil to 5w20 and filter (Not FRAM), add some lucas and it should be the fix.
- Also told to disconnect the oil pressure sensor and it would fix the problem but it will throw a code for that.
- I haven't replaced the timing chains I feel they're a little loose but they haven't jumped the teeth, so I guess they're good.
- I saw in one thread to move a teeth on phaser giving me code bank 2 (moved one teeth back and then one teeth forward but it didn't work)
When I first rebuilt the engine I was having the rough iddle then I scanned it and it gave me the cam positioning sensor code P0345, then after I replaced it problem got fixed and code was gone, I was using the truck for 2 days with no issues, then the problem cam back with the two codes P0345 and P0022!
View 13 Replies
I have a 2005 F150 5.4 and I recently got a p0175 code. I've replaced the M.A.F. sensor, fuel injectors, fuel filter, new plugs, coils and checked the vac lines but I'm still getting a p0175 code. Ive reset my P.C.M. and the code stopped for 2 weeks but returned later. The truck runs fine when I erase the code but when it returns it hesitates on take off and has a slight shake like a misfire and it makes a bubbly popping sound from the exhaust. Im at a loss of what to do next! Could this be a code stuck in the P.C.M.? My mechanic thinks it may be the cam phasers!
View 5 Replies
I have a 2004 ford f150 5.4l v8 triton lariat and while at idle it has a ticking noise like this video
YouTube...
However I also have a rattling noise when decelerating at around 2000 rpms that sounds like a loose chain in a box. Not sure if its VCT sensor or cam phasers ...
View 1 Replies
I have a 2005 F 150 5.4L and i just changed the front rotors, pads, and calipers. Because the passengers side caliper had locked and the rims was really hot and i knew it was the caliper so i changed both the driver and passenger side calipers and hoses. A month before this i had changed the pad and rotors but after the caliper locked it put grooves in the rotor and damaged the pad but the pads and rotors i bought have a lifetime warranty so i got a brand new set and changed them while replacing the calipers.
After installing everything i bleed the front brakes. But did not bleed the rear and i am wondering since i did not do the rear even though i did not touch them it is causing the front to make a ticking sound the whole time i am driving and it is starting to annoy me even though it has only been 4 days since i did the front brake job. I put Duralast rotors and Duralast Gold Cmax Premium Ceramics Pads. What is causing this ticking.
View 1 Replies
07 f150 screw 5.4 104+ miles, loss of power and ticking noise (sounds like no oil)on passengers side, no engine light, no codes, ford dealer changed coil packs and plugs, inspected valve gear on passengers side and nothing seemed out of spec, no broken springs, followers, lifters, manifolds on both sides have been replaced very recently.
The ticking noise began about a week after an oil change, truck runs fine but no power/sluggish. exhaust is magnaflow side exit and seems to be louder inside the cab than usual or could be just me.
Truck had a miss that i was trying to find prior to oil change and ticking noise. it ran well for a week with the tick before (and miss) the loss of power which started after a 30 min drive under load up hill. it almost felt and sounded as if the muffler was dragging on the road for about 100 feet, ran fine for two miles until it was shutdown. restarted fine but flat when you get into it.
Clogged cat/cats; internal damage to muffler, oil issue even tho the gauge reads fine.
View 10 Replies
I have a question about my 2007 F150 4x4 with the 5.4L. It has a ticking noise sound coming from somewhere around the motor, but it's not there till the motor has warmed up. It almost sounds like a exhaust leak, but I'm not sure. What it might be, or what to look for?
View 11 Replies
I recently got Gibson Performance Headers on my 2006 Ford F150. And when you cold start it or just start it period it has a odd ticking noise on the passenger side.
View 3 Replies
the F150 of my brother has the follow diseases:rough running ticking noises, low mileage per gallone, blue smoke out of exhaust after start, i have ordered the cam phaser, hope, that will be the reason. But today, my brother means, i have to do a test drive, because the truck has no power. and really, feels like missing of one or two cylinders. Very bad performance. Is it possible, that the reason are the phasers?
View 4 Replies
Once winter arrived I started having problems with my truck running like crap after warm up. However, I noted that during initial start up and lasting till the engine got to its Normal Operating Temp, it would run like a BAOH! Once the engine reached Normal Temp, it would fall flat on its face if I got into it down the road. I wasn't getting any codes, so knowing about the EPU and timing; I opted to change out the O2 sensors. Bought all 4 sensors, Bosh, installed them and within a day got a P0420, P0303; known as Cat system efficiency below threshold and a #3 misfire. (side not all plugs, timing chains, COP's, Phasers, cam positioning sensors have been replaced within the past 18 months) So I decided to take the COP off of the #3 cyl and swapped it with the #5 cylinder; still getting a misfire on #3.
Didn't pull the plugs, knowing they have less than 50,000 miles on them. The problem lasted about a week, off and on with heavy acceleration. Then last Saturday I was driving around town, came to a stop light and the engine shook hard while stopped, missing for a few seconds but not sending a code. Upon acceleration I noticed a loud ticking coming from the right (passenger) bank. The truck practically fell on its face through 3,000 rpm's. No power, and still no codes. I got home, pulled out my steth and listened. I got a loud ticking on the cover at the #3 and #4 Cyl. I know ya'll acclaim ticking to the phasers but it's a totally different sound. Its not coming from the front of the cover as it did when my phasers went out. This is strictly confined to #3 and #4. Took it to FMC., for diagnostic fee and a day later they said, symptoms of lash adjusters. I told them I'd pick up my truck.
Got in it, and drove it home and that noise is loud, echoing through the right exhaust. Seems to be running very rich, still no power what so ever and now I pull up in my driveway and instantly get these codes. P0316 (misfire on startup), P0420 Cat efficiency below threshold, and p1000 (due to resetting my computer back to stock before taking it to FMC) I thought about doing the job myself, but working 120 hours a week I don't see how, and I'll need to buy the valve spring compressor and timing chain wedge (260.00 set) So I started calling around to mechanics, 10 to be exact, none of which, will even look at the truck.
View 1 Replies
I have that wonderful ticking noise... Here is some info on my truck: Its 133k, 5.3L 3V. I put new plugs in it and changed the oil (YES the right filter and oil).
Okay, so I'm trying to make sure my diagnosis is what I think it is before I start digging into the motor and get angry because I ordered the wrong parts.
Preface: I got the truck from a deal auction. I was told it ran great, well when I got it, it had this tick. It comes and goes as it pleases (not dependent on the weather or RPMS. The noise is consistent, it gets faster as RPMs rise, it doesn't go away after 1,200 rpms. This lead me to eliminate cam phasers as the issue.
Now here is something odd: After starting up the truck, initially it will be pretty quick and have great throttle response, but after that it will start act like someone put on the parking brake. It can barely accelerate and when you put it to the floor it gets worse. It seems to accelerate best at half throttle. The second part is the truck will shift, dropping the rpms incredibly low and the tick gets louder and more spaced out (leading me to think it's rpm dependent).
All of the noise seems to be localized around the passenger size head area. If I unplug the VCT solenoid the ticking doesn't seem to be as loud if I drive it the next day, and it doesn't do the shift into lower rpms and accelerates wonderfully. Leading me to think it's either the timing is off and when the phasers kick on it goes way out of time and causes it to go into limp mode...or the VCT solenoid is bad?
The ticking never fully goes away, but it has it's quiet days and LOUD days...
View 1 Replies
My alarm started going off by itself and my truck would not start so we unhooked the horn but the alarm was still trying to go off making a ticking noise when the horn should have been honking. so we also unhooked the alarm. And it started right up. I've been driving it with those things off with no problem. But today it wouldn't start again and its making a ticking noise like the horn is trying to honk.
View 6 Replies
My girlfriend has an 05 ford escape with a 3.0 the car has been well maintained it has 184,000 miles on it. Over 3/4 of the miles were highway. I have noticed that it has had a slight engine ticking noise i have researched and some say the tensioner some say retorque the cams? I have not been around these cars much. I replaced the alternator the other day and serp belt all pullys felt fine. The engine used to tick all the time here lately sometimes when it gets started it does it and sometimes it doesn't.
Also what fluid is supposed to be ran in the tranny the owners manual just says mercon, so do i just run regular strait mercon fluid in it? or does it need like mercon V. The car runs fine i just want to fix the ticking noise if its something major. Just some thing I've hear about on a buddys newer f150 with a 5.4 the oil supply ports that lube the timing chain tensioner got plugged and it developed a ticking noise? I am a mechanic so i can check and do anything i just dont know where to start on this car?
View 1 Replies
2008 Accent. Timing belt broke. Took the head off and had valves replaced (2) and head work done. Had everything put back together. Car runs. Except it makes a slight ticking sound when warm. When it's cold it ticks a lot.
View 5 Replies
