I have a 2005 f150 4x4 with a 5.4 it was studdering on the highway under light load, i changed the plugs and coils it worked great for a day now working worse and giving a misfire #7, so i swapped the injectors around still misfire #7.
View 8 RepliesI have a 2006 F150 4x4 5.4. For a long time it idled poorly and would take 2 trys to start. Today it started shuddering and the engine light came on. The engine light went off but it still runs rough and smells of gas from the exhaust. It is not very drivable and I can't afford to take it in. I have lots of mechanical experience but not with this electronic junk and need diagnosing the problem. I have a code tester and this is what it said.
P0301 Cyl 1 Miss
P0304 Cyl 4 Miss
P0300 Random Multiple Misfire Detected
P2196 O2 Sensor Signal
Biased/ Stuck Rich
Bank 1 Sensor 1
My boss drives an '08 F-150 with a 5.4. The other week he had a horrid shuddering issue, misfire, and some known transmission issues so he took it to a shop. Supposedly the heads were pulled, heli-coiled, #7 coil was replaced, new plugs, trans rebuilt...a whole laundry list of stuff was done. He comes to me with complaints of a shudder in OD in low RPM primarily and a flashing check engine light with a #7 misfire code. I popped the hood to find no coil had been replaced (mechanics around here are REAL sketchy) so I told him to change up a new coil and I would throw it on to see if that fixes the issue.
Other than that, smooth idle and decent power with no shuddering except once in a while just coming into OD in low RPM...so around 40~ish and not throttling it hard. If he gets into it and blasts through the gears it has no shudder. I said the miss could be the whole issue, starting with the plugs and known misfire coil (#7) would be a good place to start.
A quick inspection in ~10 degree snow showed me the heads do not look like they were removed. The mechanic steam cleaned the engine, so looking for smudgy prints won't work. I know on older Fords the head gaskets stick out a little past the heads...do they on these too? He is questioning if the engine was even touched, and rightfully so in my opinion. Pulling the plugs would be the next step, but I need heat and tools for that.
My new to me 04 4.6 shuddered and misfired really bad last week, got couple misfire codes. I changed plugs which were really bad, like burnt out to .080, got a HEI ignition tester and got a healthy spark from all the coil packs. Drove it today and ran much better but still would shudder under acceleration when cold, wasn't as bad when warmed up but still noticeable. I thought if I got a spark with the tester that means the coil is ok? or is that not the last word in coil health. Or should I look somewhere else like injectors ? Haven't got any codes since plug change.
View 1 RepliesI have a new to me 2005 F150 SuperCab Lariat 4x4 with 155,000 miles on it. About a week ago I replaced the from passenger hub assembly and half shaft (torn boot). When doing that, I noticed that the IWE actuator was not working right (would not compress evenly). When taking that off, there was a bunch of rust that came out of the vacuum line ports. It started moving freely after cleaning all of that out that I could (I will be replacing it soon). I assembled everything back together and all seemed OK mechanically.
I also scanned the truck and saw the code for a bad IWE solenoid so that is being replaced tonight. I also have not checked the drivers side yet.
So...now that I have done all of that, the truck started occasionally bucking/shuddering when I slow down from highway speed to about 30mph and lightly accelerate again. It does not do it every time though. There is no grinding/whining noises either. Could this be caused by the IWE system somehow? Maybe slowing losing vacuum and having one engage and the other disengaged?
I have a 2006 Ford F150, king ranch, 4x4, super crew 135k miles. I bought the truck and shortly after noticed the miss under a load at 40-60 mph while in OD, or at higher RPMs at WOT, but never a CEL. Well 3 months went by and I couldn't take it anymore so with lots of research I decided to change the plugs. Ran seafoam through 2 tanks of fuel prior to this job to break up the carbon in hopes of none of the plugs breaking.
All 8 plugs came out with no issue and I replaced them with the Motocraft SP 515s (old ones were very nasty and brittle, most likely the original). I put copper anti seize on the end that goes through the channel in the head, however none got on the end near the electrode, and also on the threads. Put it all back together and it had the worse misfire an pretty much not drivable....flashing CEL and codes p0308, p0355, p0356. So I decided to buy 8 new coils as well, got all 8 of them on and now the truck is drivable but the miss is still there (no CEL).
Feels like maybe just one cylinder and I believe I got it pin pointed to cylinder 8. I put a vacuum gauge on it and unplugged the injectors 1 at a time and cylinder 8 is the only one that there is no change while unplugged. So I switched out the coil thinking maybe I got a bad one, still does it. My COP electrical plug has 12v Constant and also confirmed with an led it is getting signal. The injector is ticking or pulsing as i confirmed with a mechanic stethoscope. What am I missing????? Today when I get off I plan pulling the spark plug, checking for carbon tracking, check compression, check actual visual spark, and pull and clean the injector.
I have an 05 F150 with the 3v 5.4 with 170k on it. Last fall we changed the timing chains, cam phasers (aftermarket), plugs, coils (OEM), VVT solenoids (OEM), Cam Position sensors (OEM) and swapped in a GT500 oil pump. Recently under moderate load (fairly heavy acceleration onto the freeway, pulling a large camper) I get a pretty rough misfire. Tonight I pulled the codes and it was Cylinder 5 misfire. In the past I have also had Bank 2 Over-Retarded code. What are the next things to verify and check? I plan to clean the throttle body and change fuel filter but I'm not sure either of those would cause the misfire code?
View 3 RepliesI have a 2000 f150 5.4 liter engine. I traveled about a month ago and while on the highway it started "bouncing/shuttering" really bad. I pulled off and while still in drive but completely stopped it was still bouncing but when in park it stopped. I took in into the Ford dealership and they said that cylinder 5 was misfiring and it was losing pressure fast. Then it stopped acting up completely and they couldn't find anything wrong with it.
Well about a week ago it started bouncing again on city roads (no highway). The check engine light came on and Orielys said it was a cylinder 5 misfire. Also, under the oil cap and in the tube where you would put the oil in has a yellow thick substance on it. I know that it is water in the oil. Also, there is a black "gunk" not far from where you would put the oil in. Could these problems be connected?
2005 Ford F150 lariat 5.4
I had a misfire under a bit of a load (acceleration) and up hills. I changed spark plus with OEM Motor craft ones, truck ran super nice for a couple week.
Had the engine light flash, slow down and the RPM go up a tiny bit then back down and the light goes off
Now I'm back to miss fire different location, and a rough idle. I've swapped coil packs around and the miss fire stayed on cylinder 4.
Spark plug screwed or injector or ?????
E brakes were sticking so I took off wheels, rotors, calipers, and cleaned the E Brake caliper and lubed it. Started driving and E brakes are still sticking? What gives? Could the cable be hung up? Wonder if I should replace the E brake cables.
View 4 RepliesI just purchased a used 2006 package 3 with 66500 miles on it. Drove it to work today and the car started sputtering/shuddering when i was accelerating onto the highway. The check engine line came on so I took it to the dealership. Turns out it was a bad sensor.
When they fixed the bad sensor, the mechanic told me that its normal to feel a slight stuttering when the gas engine kicks in or off which seems to be confirmed by other members here.
2008 5.4L ...I started a thread before concerning my tranny shuddering while in OD. It did it before and after a tranny rebuild. That's when I learned of the common problem of a bad coil pack not allowing trans to lock out into OD. Yesterday I took the truck to a shop to have it scanned. I was hoping to find out which cylinder is the problem. No fault codes were found. Now the mechanic thinks its the tranny, and the tranny guy(who has had the truck twice) says its a coil pack. I can change it if I can figure out which one it is. Do I have anymore options left to find the bad coil pack, or am I left with changing them all.
View 2 RepliesMy wife was driving her truck yesterday and said the MIL light started to flash and the truck felt like "it was about to blow up" . So when I got home I busted out the trusty old scanner and this is what I got:
P0305- Cyl 5 misfire'
P0354- Ignition coil D primary/ Secondary circuit malfunction
P0304- Cylinder 4 misfire
The truck is a 2005 5.4 with ~130,000 on it and it runs very well for the most part. I have done the spark plugs before the summer and replaced them with the motorcrasft sp-515s. I am guessing the problem will be with the #4&5 coil packs. is there a way to troubleshoot these?
I have a 2005 f150 with 96,000 miles. Long story short, last August I was headed to the mountains going up a steep long hill and the engine light come on. once i was over the pass the light went off. During my 4 wheelin' trip it never came back on until I was headed home and going over another pass and then it stayed on for a couple of days. I had it checked and it was a cylinder 5 misfire. I did some research and found that replacing the coil cover might fix the problem and if not the spark plugs would need to be changed.
I changed the coil cover, problems solved... until I headed to the mountains. light came on and then eventually went off later that day. I didnt think much of it. then a few months later i was headed to the mountains again and the light came on in the same place on the steep incline hill. I. took it back to the shop, same reading. I decided it was time to replace the spark plugs anyways so I would invest. I have new plugs and everything is good however, I had no plans to go to the mountains in the near future. Now, a few months later I headed to the mountains and crossed my fingers it would not come on but it did.
I've done the research again and it seemed like the coil cover and spark plugs are usually the cause of the problem...however I have changed mine. The light is now off again. I don't understand what is triggering the problem and what is really happening and if it is safe to keep taking to the mountains with this happening. I did notice that everything was fine at 60MPH but once i hit the hill and steeped on the gas to go 65 and hit 4-5RMP that is when the check engine light came on...
I have a 2008 FX2 5.4L F150. Recently it began to lose power on a friend driving it out of town. He got a check engine light then it just progressively became unable to produce power. It ran but he got down to 10 mph before he could get to a firestone. I got it to a local Ford dealer and they say i need a new engine. They gave me codes for cam sensor and timing and #5 and #6 misfire. (344, 345)
No oil in radiator, no water in oil. The crazy thing is it runs like the day i bought it in Park. But once in gear it begins to cough and then eventually shudders and dies. I haven't changed plugs ever. I know... At about 75 miles it began to idle rough at times and in reverse. But once I revved up it went away.
I replaced both cam sensors but no luck. Today i put it on a tow truck to get a second opinion from a local engine shop. I actually backed it down my driveway, and pulled up to the tow truck with no issues. weird...
Over the past few months I've noticed that my truck has a very intermittent shudder under mild acceleration. If I accelerated more during the shudder it seemed to disappear until I let off the peddle a little. When it happens the truck doesn't seem to be lacking power and the engine throws no codes. It happened again today right as I had stopped at a red light. I noticed that it was shuddering at idle too. I shut the truck off at the intersection and the shudder was gone once restarted. What it may be?
View 5 RepliesIll start off with my mods and recent maintenance things I have done before fully describing the issue.
E99 7.3l with 190k on the clock
Full 5" turbo back
TS-6 chip
EGT, Boost and trans temp gauge
New ford glow plugs
Re-orings injectors
new valve cover gaskets
new fuel filter and fuel lines
new turbo with a ww2
Newer trans and oil pan
I think that should do it, now for my problem. The truck starts good cranks over once and is running with no hesitation, the engine run a little rough, more than normal vibration at idle almost like a small miss. No smoke at idle.
While driving with no/little load on the engine runs great , but under load there is a good amount of white smoke/ oil smell. The turbo is new and is not leaking oil I have already checked over that and the exhaust is new but there is some oil that is at the tail pipe in liquid form. The exhaust up pipe that goes to the turbo is not covered in oil either
The truck cruising in OD or in 3rd with O/D off around 2k rpms it shudders real bad almost like the truck is going to shake its self apart. but at like 2400 rpms and above its fine. Where is a good place to start the diagnosis as I am pretty new to the Diesel world. From what I've read it looks to be either rings are junk or maybe I have some bad injectors (thats what it feels like to me) but would that cause it to smoke like crazy?
2006 F150, 4.6 V8 ... My truck was running fine until one morning I was sitting in the truck giving it my customary 30 second morning warm-up and it starting running very rough and quickly threw Check Engine LED.
I hooked up my laptop and got the following error codes: (To assist with future searches, the error codes are P0302, P0303, and P0353)
It seemed to drive fairly well, but low RPM torque causes major shuddering, so I try to keep the revs up to avoid damaging other components. The first step was to replace the spark plugs. They looked to be original and I'm at 140K on the truck, so it's probably time.
I went with Bosch Platinum as the factory plugs were platinum. When replacing the plugs, I moved the coil pack from cylinder 2 to cylinder 3 to determine if the problem would move. After the plug swap, the engine did run noticeably smoother (so the plugs worked overall), but still had the low rpm shudders and the same error codes (after clearing them).
Unfortunately, the error codes still indicate cylinder 2. I guess a misfire could be related to the fuel injector as well, not firing at the right time or not a complete spray, but what else could cause this?
2004 GMC Sierra 2500 HD, 227,000 miles 6.0L V8.
While driving up hills or increasing load, the CEL will flash multiple times, I pull over as I know CEL flashing is not good. I turn the truck off, allow it to sit for a few minutes, whip out the code scanner, only code that was there happens to be P0300. Truck has poor MPGS, idles rough, loss of power. this happens every time I drive this vehicle as I use this truck to pull my trailer that weighs around 4000 lbs. Problems come and go. Some days I can drive the truck for an hour with no problems, come up to a red-light, BAM, CEL is flashing, truck is bouncing side to side due to the poor idle, other days this happens while sitting in the parking lot of my job with the ac on.
Truck has been to the shop several times as I'm no mechanic. Parts replaced are as follows:
- Fuel pump
- Throttle Body
- All plugs
- All wires-All Coils
- Intake Manifold Gasket-
- Battery
- Sensor 1 Bank 1 O2 Sensor
- Sensor 1 Bank 2 O2 sensor
Have a friend and looking at his truck for him. He was towing a boat and climbing a steep grade hill. As he described it, it felt like he lost all power. Did manage to get it to the top of the hill and stopped to check it out.
Noticed the under of the truck dripping oil. Checked the motor oil and none on the stick. Put 4 quarts in the motor, started it back up and oil pressure is good and motor sounds fine.
The strange thing is the motor is dry. Can not find where the oil leaked out. All the oil is located on the transmission and transfer case. I'm not too familiar with these Triton 5.4's but where could that oil possibly have come from? I'll re-look this morning.
Also, with oil in motor, and it is idling, there is no oil leak or drip anywhere. Is there a pressure regulator in this oil system and the load he was exerting cause it to release?
I have a 2004 f150 lariat crew cab 4x4 with the 5.4 3 valve. It now has 113 000 miles. Since i got it at 85 000 miles its had a hiss when the engine was under load. So like light acceleration or driving into wind. The guy i bought it from said that it had a manifold leak so that's what i figured it was. I got the manifold fixed and it still hisses. There are no check engine lights. It almost feels like my engine lags when it starts hissing. It sounds like its coming from right on the other side of the fire wall. What it could be?
View 3 Replies