Ford F-150 (2004-2008) :: Rough Idle / Bad Gas Mileage / Stalls Out / RPMs Jumps Around
Jul 12, 2013
I bought an 04 f150 super crew cab with the 5.4L triton in it 3 years ago with 50k on it from my great uncle who was the original owner. It's had a tick to it since he had it but the dealership told him they couldn't find anything wrong with it and to get use to the noise. It's ran pretty good up until last couple months where it's been running really rough and not doing the best. It's still hasn't been all the time but more intermittent and comes and goes, but when it's running bad the rpm drops down to about 200 and my motor sounds blown.
When that's happening I could put in neutral and rev it up and it would go back to normal for a bit, but now it's all the time and stalls out even at 70 on the hwy. The codes it throws are, p1000- monitor checks not complete-more driving required, p0345- camshaft pos sens circ error(bank 2), p0022- A camshaft pos timing-over retarded bank 2. Things I have tried-changed all 8 plugs, added K&N air intake, replaced both cam sensors, replaced fuel pump driver module (due to corrosion). Tonight I'm going to clean the throttle body, mas air flow sensor, change fuel filter.
View 14 Replies
Advertisement
I have a 2004 FX4 5.4 with about 113,000 miles on it. Lately, when towing the camper (around 7000 lbs), truck runs great. However, when I come to a stop, it idles horribly and even stalls sometimes. When I rev it up, runs fine again. It only does this after towing when engine is under load for extended periods of time.
The only code it has ever thrown was for bank 2 camshaft over retarded. My thought was that it could be VCT solenoid for bank 2...
View 2 Replies
I have a 2001 Ford Escape, and when I start it for the first time of the day, it idles really rough, and way below 500RPMs (to the point where it almost stalls). After about 10 minutes, when the car is all warmed up, it runs smoothly, as if there was nothing wrong with it. The only conclusion I can draw is that it is temperature related, but I can't figure out exactly what is causing the issue. This happens on the driest or wettest of days, so moisture doesn't seem to be an issue.
View 2 Replies
2007 5.4 . Starts good , idles all day. As soon as you try to rev it, it stumbles rattles etc. Shut it off, wait a second, restart then Idles fine. I watched live Data and it carries on when the VVT solenoids become active (above 800 rpm).There duty cycle goes to 60-70 percent while revving. I think it Is just one side of the engine. Could be VVT solenoids sticking on? yes ? No?
View 3 Replies
Let me start with I have a 2003 f250 5.4. The motor blew on my truck and I had a 100k motor dropped in it. I've put new spark plugs, ohmd out the coils. I tried both sets of injectors. cat delete and new fuel pump. It has rough idle and stalls but runs fine at higher rpms. Also has basically no brakes. I am thinking vacuum but I've check all the lines. No codes either!! also cleaned throttle body.
View 4 Replies
Hot or cold car always starts,Idles perfect , then RPM drops, Idles rough and stalls. Econometer moves to Red area.car will easily restart and drives well,it also idles well. Once engine is shut down, even for a short while, It does the same thing again. Car is used for short trips. Ambient Temperature 80 degrees. Once running car is perfect at all speeds and idles smoothly. Hero 1987 MB 560 sel ....
View 19 Replies
the F150 of my brother has the follow diseases:rough running ticking noises, low mileage per gallone, blue smoke out of exhaust after start, i have ordered the cam phaser, hope, that will be the reason. But today, my brother means, i have to do a test drive, because the truck has no power. and really, feels like missing of one or two cylinders. Very bad performance. Is it possible, that the reason are the phasers?
View 4 Replies
It has been so effective to add diesel injector cleaner to my 2004 Honda (all of 62,000 miles on it), that it is scaring me. Am I damaging anything? I add about an ounce/gallon every once in a while. Mileage drops back in between.
View 10 Replies
I changed the plugs on my 2004 F-150 FX4 with 165,000 miles. Immediately afterwards I experienced a low idle problem. After engine warms up, idle is at about 400 rpm in nuetral or park. When I put in gear it drops to 200 rpm and sometimes stalls. Ford analyzer says misfire #8 cylinder. I swapped coils with #7 and reset fault. #8 cylinder misfire came back. So next I put new plug in #8 thinking the plug was bad. Still have low idle problem. What I should try next?
View 3 Replies
I have a 2007 Ford F-150 5.4l v8...
Codes
P0012 int cam position timing over ret bank 1
P0022 int cam position timing over ret bank 2
P0300 random Missfire detected
P0316 engine misfire detected on start up
P0340 cam position sensor curcuit fault
P0345 cmp sensor a circuit problem bank 2
Starts rough, idles rough and stalls occur often when start, after it runs for 5 minutes and sometimes dint starts at all. I replaced spark plugs, coils, cam shaft sensors and had oil changes done and. No effect.
View 8 Replies
Within the past few days my towncar has developed a rough idle. When I'm stopped at a light or stop sign it jumps and just plain idles rough. This also happens when I change speeds after either accelerate or decelerate. I travel an average of 80 miles a day total to and from work and my car has about 140,000 miles on it.
View 13 Replies
On my way into work this morning, my 06 with the 5.4 started running very rough/shaking at low rpms. I could kick it out of overdrive and it would smooth out and seemingly be fine at higher rpms.
This worked out for a couple of miles until the truck just died on me completely. The Edge is showing po351, 352, 353......358 codes. Ignition coil Primary/Secondary circuit fault on every cylinder.
I'm thinking its unlikely that every coil failed simultaneously....computer? When I try to start the truck, it will try to hit on a cylinder or two, but will not run.
View 3 Replies
I was driving on the highway today, and when I turned onto the exit ramp and put the car in neutral I noticed my gear shifter shaking back and forth pretty violently. I looked down at the tachometer and saw it idling at less than 200 rpm's in neutral. I got to the light and my car stalled. I turned it back on and I had to feather the gas pedal just to keep the car running. I was able to make it to my local car mechanic with one foot on the gas pedal and my hand on the e-brake. It runs a little rough when in gear but at least it keeps the rpm's up enough to stay running. The check engine light never came on. My guy said that he didn't have the appropriate diagnostic machine, but he's afraid I might need a new throttle body and a new computer which may cost 1000's of dollars. I think the code he told me that he found was P0506. He sent me to a guy that deals only with Japanese cars, but they won't be able to look at my car until Monday.
Any thoughts? Hopefully something that doesn't cost 1000's of dollars. And if I replace the throttle body does that mean I have to replace the computer too? Is there something that I did or that I didn't do that I should have been doing that could have caused this to break?
View 6 Replies
I have a 2004 SD with 5.4 that is running pretty rough both at idle and driving. Truck shakes a lot at lower rpms. I have a scan tool and had a misfire on cylinder 4 so I replaced the coil and the plug. Also replaced the idle air control valve. Plan on replacing O2 B1 S2. (One of my codes) even after replacing the coil and plug I'm still getting misfire detected from cylinder 4??? Other codes I had were misfire detected on he first 1000 revolutions. That hasn't come back though.
View 2 Replies
I have a 100% stock 2004 Celica GT ~125,000 miles. Over the last few months I have been getting a rough idle and stumble at low rpms. The other day the car would not restart after sitting for about 20 minutes. Only recently has it actually thrown a DTC. The error codes were for misfires (P0300, P0301,P0302,P0303, P0304). I don’t get a code every time but the problem seems to be more noticeable if the car has been ran for a while, sits for 20-30 minutes while in a store and then when I try to start it when I come out of the store is when the problem most often occurs. When it restarts it will stumble at low RPM and if I hit the gas it has little response and misses badly. I have never used a scanner until now. I am using a Autel MS509 scanner and I am not sure it is giving me the correct diagnostic numbers for the live data. I think the DTC are correct but the live data is questionable.
Here is what I have done so far.
- Cleaned IAC valve (completely removed and cleaned)
- Searched for vacuum leaks using carb cleaner
- Cleaned MAF sensor
- Replaced all 4 injectors
- Replaced upstream and downstream O2 sensors
- Replaced Coolant Temp Sensor
- Ensured cam tensioner is providing adequate pressure to the cam chain
- Tried 2 sets of new Iridium NGK plugs and a new set of Bosch Copper plugs
- Moved coil packs around
- New air filter
- New fuel filter
- SeaFoam through intake and gas tank. I have not mixed in the oil.
- Compression Test (1=190,2=190,3=160,4=178)
Things I have not done.
- Taken it to the stealership
- Fuel pressure test
- Valve Clearance
I am concerned about the compression test because according to the service manual it should be around 218. I was using a Harbor Freight compression tester and I am not 100% sure I had a good seal with the tester.
View 14 Replies
Just got 2005 screw fx4. Seemed to run ok 115000 mi.Had exhaust leak,I put on 3" cat back on. Then I noticed tapping at front of the engine.Turns out tim. chain guides are broken. looks like very common prob after reading many forum/threads. Anyway got timing chain kit, phasers, selinoids. Truck runs and sounds great.But so far had truck back 2weeks stalled 2x at idle.What next??
View 14 Replies
2004 Trailblazer 6cy. 2WD - has been experiencing a very rough idle, engine shudders - no matter how long it's been warmed up. Wants to stall off red lights and at very low speeds. Not throwing any lights yet - but the speedo is out ( a cam shift typical problem for this car) so I don't trust the console for lights. Worse when the heat or air is on. Rides fine with more gas/higher speeds. Definitely worse in colder temps but continues even after 40-50 mins of driving. I've heard a number of things, but can't afford to fix them all. I've heard plugs, dirty throttle camshaft, sensors, cam actuator solenoid, etc. All seem to have people who said it fixed and didn't fix the issue. Worried I'm going to stall pulling off a stop and rear end someone any day now. Where do I start!?
View 2 Replies
I have a 2006 f150 I just bought after my F250 was stolen. It has about 70k miles. It has been running pretty rough ever since I got it. It finally threw codes so I tried to address all the issues. Changed out a couple coils and all the plugs (motorcraft platinum). The camshaft sensor was also bad. Truck runs much better but still has an idle issue I cant seem to nail down.
I assume its something to do with air intake. It doesnt happen all the time. It runs rough and knocks and sometimes dies. If I give it gas it stops. I read it could be the idle air intake valve, but then I read that this model doesnt have one. I also read that air intake issues dont normally throw codes. Are there any common problems I could look for? Would cleaning the throttle body do any good?
I know the basics, but this kind of thing is tough for me to troubleshoot. You may have already seen me post this problem, but I didnt get much response so I thought I'd try one last time.
View 11 Replies
Ok, so I just replaced the entire timing set (phasers, chains, sprocket, tensioners ect) on my 2004 f150 5.4l about a month ago. I also extracted ALL 8 spark plugs and replaced those with the Champion 1 piece plugs. In addition, I replaced the intake manifold because I did this job when it was 20 degrees outside and I found a crack. Soooo, all that being said I put the whole truck back together and it runs like New. Until about a month later. When the engine gets hot, maybe after about a 30 minute drive or so, it has a really really rough idle until I give it a little bit of gas. Then it clears up. It has only done it 3 times since I put the engine back together. It might go 2 weeks and not do it. No codes. What I could be? EGR? MAS air? Only other thing I can think to say is if you get on it out on the highway, after about 3k rpms it seems like the power drops off quite a bit. Like the engine isn't getting enough fuel. I guess it could be just me, but it just doesnt seem right.. I guess I could try to unplug the MAS air flow sensor...
View 14 Replies
I hopped in my truck this morning, fired it up, and it idled nicely. I drove around the corner, and noticed that the truck was barely responding to the throttle. Then things got shaky. It was a very rough idle, almost like a misfire. But I managed to get the gas to respond and got the revs up to about 3K and it seemed to run smooth.
No CEL either. Currently, I have no place to really look at my truck as I don't have a garage, or driveway for that matter. I don't have a scanner that can read live data either. I'm limited in my tools currently as well.
View 3 Replies
I have 2008 f150 with 5.4 and 54000 miles. It has a bad vibration or rough idle only when AC is on. When AC is off it runs very smooth. Runs great while driving with AC on. Tensioner pulley was moving a lot more than normal when engine started vibrating so i replaced it and the belt but it didn't work. I also checked the other pulleys and they are good.
View 1 Replies
