Ford F-150 (2004-2008) :: Rough Idle When Come To A Stop And Even Stalls Sometimes
Jul 2, 2012
I have a 2004 FX4 5.4 with about 113,000 miles on it. Lately, when towing the camper (around 7000 lbs), truck runs great. However, when I come to a stop, it idles horribly and even stalls sometimes. When I rev it up, runs fine again. It only does this after towing when engine is under load for extended periods of time.
The only code it has ever thrown was for bank 2 camshaft over retarded. My thought was that it could be VCT solenoid for bank 2...
View 2 Replies
Advertisement
I bought an 04 f150 super crew cab with the 5.4L triton in it 3 years ago with 50k on it from my great uncle who was the original owner. It's had a tick to it since he had it but the dealership told him they couldn't find anything wrong with it and to get use to the noise. It's ran pretty good up until last couple months where it's been running really rough and not doing the best. It's still hasn't been all the time but more intermittent and comes and goes, but when it's running bad the rpm drops down to about 200 and my motor sounds blown.
When that's happening I could put in neutral and rev it up and it would go back to normal for a bit, but now it's all the time and stalls out even at 70 on the hwy. The codes it throws are, p1000- monitor checks not complete-more driving required, p0345- camshaft pos sens circ error(bank 2), p0022- A camshaft pos timing-over retarded bank 2. Things I have tried-changed all 8 plugs, added K&N air intake, replaced both cam sensors, replaced fuel pump driver module (due to corrosion). Tonight I'm going to clean the throttle body, mas air flow sensor, change fuel filter.
View 14 Replies
2004 Trailblazer 6cy. 2WD - has been experiencing a very rough idle, engine shudders - no matter how long it's been warmed up. Wants to stall off red lights and at very low speeds. Not throwing any lights yet - but the speedo is out ( a cam shift typical problem for this car) so I don't trust the console for lights. Worse when the heat or air is on. Rides fine with more gas/higher speeds. Definitely worse in colder temps but continues even after 40-50 mins of driving. I've heard a number of things, but can't afford to fix them all. I've heard plugs, dirty throttle camshaft, sensors, cam actuator solenoid, etc. All seem to have people who said it fixed and didn't fix the issue. Worried I'm going to stall pulling off a stop and rear end someone any day now. Where do I start!?
View 2 Replies
I am having trouble with my 1998 F-150...XLT Triton? I bought the wrong motor for it and installed it, turn out it's a 1999 Windsor 5.4
Problem is that it runs rough and stalls when I stop or rolling to a stop it would die.... It seems ok while cold, but when driven for 20 minutes or more it does it.
I have used original 4.6 harness as well as original spark plug coils and only replaced throttle body, oil filter holder thingy mount, exhaust manifolds are from 4.6.
When the throtle body was on the 4.6 I didn't have when the motor ran. Only misfire due to intake manifold leaking into the 3rd cylinder spark plug.(I thought it was a bad head gasket and changed in....installed the timing chain wrong and messed up the whole motor)
Also I broke a rear brake line and now it only has front brakes and smells like fried transmission oil.. This is my first truck and first truck accidental engine swap. Also the 5.4 Intake manifold is missing 2 coolant sensors and it's giving me the P0118 ECT Sensor Circuit High input...
View 2 Replies
I changed the plugs on my 2004 F-150 FX4 with 165,000 miles. Immediately afterwards I experienced a low idle problem. After engine warms up, idle is at about 400 rpm in nuetral or park. When I put in gear it drops to 200 rpm and sometimes stalls. Ford analyzer says misfire #8 cylinder. I swapped coils with #7 and reset fault. #8 cylinder misfire came back. So next I put new plug in #8 thinking the plug was bad. Still have low idle problem. What I should try next?
View 3 Replies
I have a 2007 Ford F-150 5.4l v8...
Codes
P0012 int cam position timing over ret bank 1
P0022 int cam position timing over ret bank 2
P0300 random Missfire detected
P0316 engine misfire detected on start up
P0340 cam position sensor curcuit fault
P0345 cmp sensor a circuit problem bank 2
Starts rough, idles rough and stalls occur often when start, after it runs for 5 minutes and sometimes dint starts at all. I replaced spark plugs, coils, cam shaft sensors and had oil changes done and. No effect.
View 8 Replies
I was driving on the highway today, and when I turned onto the exit ramp and put the car in neutral I noticed my gear shifter shaking back and forth pretty violently. I looked down at the tachometer and saw it idling at less than 200 rpm's in neutral. I got to the light and my car stalled. I turned it back on and I had to feather the gas pedal just to keep the car running. I was able to make it to my local car mechanic with one foot on the gas pedal and my hand on the e-brake. It runs a little rough when in gear but at least it keeps the rpm's up enough to stay running. The check engine light never came on. My guy said that he didn't have the appropriate diagnostic machine, but he's afraid I might need a new throttle body and a new computer which may cost 1000's of dollars. I think the code he told me that he found was P0506. He sent me to a guy that deals only with Japanese cars, but they won't be able to look at my car until Monday.
Any thoughts? Hopefully something that doesn't cost 1000's of dollars. And if I replace the throttle body does that mean I have to replace the computer too? Is there something that I did or that I didn't do that I should have been doing that could have caused this to break?
View 6 Replies
2008 Dodge Avenger SXT Sedan GEMA 2.4L DOHC I4 / 4 speed automatic75,000 miles Moderately well taken care of (oil change every 3,000 miles, mostly follows recommended maintenance in owner's manual)
Symptoms:
*Car runs and drives fine while the car is in constant motion and decelerating.
*Rough and Slow Idle at a stop on the brakes with car in Drive. Engine speed will drop below ~400 RPM, then "kick" up to ~1,200 RPM, settle back to 'normal' idle ~800 RPM, repeat. I have suggested she put the car in Neutral at a stop to see if that changes anything, but I don't have feedback from her yet. One instance of seeing a puff of smoke from under the hood while the car was doing the above.
*When pulling away from a stop, the car will hesitate; that is the accelerator will be pressed but the throttle response will be delayed.
*When pulling away from a stop acceleration will be inconsistent; instead of rrrrrRRRRRRRRRR, it's more like rrrrRRRRrrrrrRRRRrrrrrRRRRR
*Couple instances where the car just shut off while she was parallel parking (low engine speed).
*One instance where the car did not start on first attempt. Started fine on second attempt.
*No Check Engine Light. The codes have been run.
Shop Visits (at an independent garage recommended by her roommate who's been going there for 5+ years, good reviews on yelp, and always busy):
*First visit: told her they put in a bottle of fuel system cleaner and to use a tank of high octane gas. That didn't really work.
*Second visit: cleaned the throttle body. That was 3 days ago, so far no conclusion either way.
Other repairs:
*The battery was checked (at O'Reilly) and replaced after the starting incident mentioned above. (5 year old car, seems about right).
*2 nights ago I told her to put in a bottle of HEET to get water out of the fuel system (California uses ethanol blend) and a bottle of Gumout Fuel System Cleaner and to fill up with premium gas (based on items below). Be sure to run that tank down to almost empty.
Things I could think of:
*Crankshaft/camshaft position sensor failing.
*Alternator failing (because this problem doesn't seem to exist at higher RPM's)
Research online: It seems that a number of people have similar problems with Chrysler products with this and the previous generation 2.4L engine but no clear conclusive repair. Some of the items mentioned:
*Idle Air Control (IAC)
*Exhaust Gas Recirculation (EGR) valve
*New sparks plugs and wires. (not replaced but should be)
*New timing belt. Timing belt is one tooth off.
*Water in the Fuel System (hence, HEET)
*Dirty/Clogged Fuel System Component (hence, fuel system cleaner)
*Failing Fuel Pump
*Dirty/Clogged Air Filter (replaced per maintenance manual)
*Low Oil Pressure/Failing Oil Pump
*Additionally, there are no recalls against her VIN.
View 1 Replies
Just got 2005 screw fx4. Seemed to run ok 115000 mi.Had exhaust leak,I put on 3" cat back on. Then I noticed tapping at front of the engine.Turns out tim. chain guides are broken. looks like very common prob after reading many forum/threads. Anyway got timing chain kit, phasers, selinoids. Truck runs and sounds great.But so far had truck back 2weeks stalled 2x at idle.What next??
View 14 Replies
I have a 2006 f150 I just bought after my F250 was stolen. It has about 70k miles. It has been running pretty rough ever since I got it. It finally threw codes so I tried to address all the issues. Changed out a couple coils and all the plugs (motorcraft platinum). The camshaft sensor was also bad. Truck runs much better but still has an idle issue I cant seem to nail down.
I assume its something to do with air intake. It doesnt happen all the time. It runs rough and knocks and sometimes dies. If I give it gas it stops. I read it could be the idle air intake valve, but then I read that this model doesnt have one. I also read that air intake issues dont normally throw codes. Are there any common problems I could look for? Would cleaning the throttle body do any good?
I know the basics, but this kind of thing is tough for me to troubleshoot. You may have already seen me post this problem, but I didnt get much response so I thought I'd try one last time.
View 11 Replies
Ok, so I just replaced the entire timing set (phasers, chains, sprocket, tensioners ect) on my 2004 f150 5.4l about a month ago. I also extracted ALL 8 spark plugs and replaced those with the Champion 1 piece plugs. In addition, I replaced the intake manifold because I did this job when it was 20 degrees outside and I found a crack. Soooo, all that being said I put the whole truck back together and it runs like New. Until about a month later. When the engine gets hot, maybe after about a 30 minute drive or so, it has a really really rough idle until I give it a little bit of gas. Then it clears up. It has only done it 3 times since I put the engine back together. It might go 2 weeks and not do it. No codes. What I could be? EGR? MAS air? Only other thing I can think to say is if you get on it out on the highway, after about 3k rpms it seems like the power drops off quite a bit. Like the engine isn't getting enough fuel. I guess it could be just me, but it just doesnt seem right.. I guess I could try to unplug the MAS air flow sensor...
View 14 Replies
I hopped in my truck this morning, fired it up, and it idled nicely. I drove around the corner, and noticed that the truck was barely responding to the throttle. Then things got shaky. It was a very rough idle, almost like a misfire. But I managed to get the gas to respond and got the revs up to about 3K and it seemed to run smooth.
No CEL either. Currently, I have no place to really look at my truck as I don't have a garage, or driveway for that matter. I don't have a scanner that can read live data either. I'm limited in my tools currently as well.
View 3 Replies
I have 2008 f150 with 5.4 and 54000 miles. It has a bad vibration or rough idle only when AC is on. When AC is off it runs very smooth. Runs great while driving with AC on. Tensioner pulley was moving a lot more than normal when engine started vibrating so i replaced it and the belt but it didn't work. I also checked the other pulleys and they are good.
View 1 Replies
Is it possible to have an intermittent injector problem I am having the same problem with my 2004. Its not all the time its rough only at idle constantly. If I keep the rpms up it doesn't do too bad...
View 1 Replies
An injector stuck open on my 05 5.4 and bent a rod. I had a new rod put in and all new revised Motorccraft injectors. This was about a month ago. Truck has ran great for the past 3 weeks until today I put it in park and it idles real rough, put it in gear and it smooth as butter again? (Once in a rare while it will continue to idle rough in gear for a few seconds but then clears up.) New motorcraft plugs were put in right before it bent the rod. The truck runs real strong other wise. I am about done with ford this pickup has been the biggest pile I've ever owned one thing after another and just when I think its fixed its some other stupid problem. I'll start by cleaning the maf and throttle body. Could it be a bad coil?
View 3 Replies
I purchased an '08 F150 about 6 months ago, and have a problem that two mechanics haven't been able to solve. The truck has a 5.4L engine. Unfortunately, I bought from an auction and the 30 day warranty expired before I realized the problem.
After a longer drive (30 minutes to work) the engine is warm, and I always back into my parking spot or driveway. In low gear, it begins to idle very rough and the engine shakes. If I leave it long enough, it will stall. Usually I pop it into neutral, give it some gas, and its fine. I just bought a camper trailer, so I'll need to use the lower gear when backing up.
So far, the engine has been flushed twice, the solenoid replaced and phaser replaced. The second mechanic has recommended I contact a dealer, but haven't had luck with them with my previous Explorer. What it could be? I will be getting the diagnostic paperwork this week.
View 14 Replies
I have a 2005 5.4l f150. 105,000 miles. Recently While on a trip I experienced rough idle and stalling at idle. I drove it home 2hrs. The ride home was challenging. Poor acceleration, rough idle. Took it to the dealer and was told I needed plugs and I was 5qts low on oil! Not sure where the oil went. It hasn't been leaking and never seemed to burn oil in the past. They did the tune up. Picked up the truck. It ran fine while cold. Upon warming up it ran rough at idle and stalled just like it did before. Took it back, they said "you need a new engine. Upon warming the oil pressure drops indicating internal engine damage". I took it to a local guy he says replacing the cam phasers might fix it. What's the consensus, should I try the cam phasers? Look for some other potential problem or trust the dealer? (They did refund me for the tune up)...
View 14 Replies
2005 f-150 4.6l v8 rough idle only when truck is to normal operating temp. I have run several gas system cleaners through the truck. I replaced the air filter, the fuel filter and the spark plugs. I am only getting 14to 15 mpg mostly highway. No DTC's are showing up. The truck only has 50,000 miles.
View 6 Replies
Okay I have a 2006 F-150 5.4 60,000 miles , Never once had any problems. I have always done the oil changes myself using 5w-20 mobile super and an S2 STP oil filter. Today, I did a normal oil change and once i filled it up I checked the oil it one last time and I topped it off just right according to the dipstick. And I also checked it after letting engine idle for 5 minutes. I changed the fuel filter also ( first time doing) but no leaks. I drove about two miles down the road, turned around and when I put it into reverse it idled really rough. It almost sounded like a thrown rod.
The rpm's dropped to about 500. I put it into drive and gave it a little gas and then all was fine. Engine ran perfect. I reversed it at least 5 more times and it did it every time but always recovering when given a little gas. I also noticed that there is some oil splashed on the undercarriage like it was leaking going down the road. I checked the filter gasket and it was fine and intact. It idles great in park, drives great. Just reverse it dives down and vibrates like crazy.? After getting home I noticed that the oil level on the dipstick is a little less than a 1/4 inch over the correct level.
View 12 Replies
Let me describe this perplexing issue. I have a speratic rough idle problem. When it happens it's almost like the truck wants to stall. Once going the truck is fine. There has never been any acceleration issues, but for a short time the truck would kind of lunge off idle. It hasn't done that for quite some time. I've replaced the fuel filter. There are no vacuum leaks that I know of. I've tried higher octane fuel. I've tried injector cleaner for a month. What should the fuel pressure be and what is the test port located? Is the fuel pump in the tank? If so, whats that big log looking thing behind the gas tank that the fuel lines run to? Also, there are no MIL codes...
View 14 Replies
I just received a 06 F150xl with a 5.4 triton and idles rough with the following codes! p0357 p0012 p0340 p0344 p0351 p0352 p0356 p0358 p0357 p0102 p0113 p0353 p0354 p0355 It's amazing the truck even runs and with no light on but it will accelerate. someone mentioned to clear the codes and drive it 50miles or so and read them again.
View 9 Replies
