is there an way to remove the defrost vent covers? i think my license slid down the front of the defrost covers. its probably somewhere down under the dash. I would like to start removing the covers up top before I yank the dash. I am 1400 miles from home so I cant run and get a replacement.
View 6 RepliesI've got a couple different problems. The first one is that no matter what setting I have it on, air only blows out of the defrost vent.. Why this is happening? or is there already a thread about this? i saw a thread for this same problem, but it was for 2nd gen explorers.
The second problem I have is that there always seems to be air blowing from some where on the passenger side, unless i am accelerating. I can't seem to find where it is coming from but it makes a really annoying noise.
It is the 4.6L, AWD. not sure if that matters or not though.
How to remove the center dash air vent on a 2008 TCH?
View 2 RepliesI took my car in for its first detail (while mine, that is). How to keep the front vent covers open with the car off, for purposes of cleaning the vent directional slats. The best I could figure out in a hurry was, with the key in accessory or the engine on, to switch climate to manual (direct air) to open the covers, set the fan to lowest speed (one light segment above off,) and position the vent switches to furthest left light illuminated (again, one position above off.) Is there any way to keep the covers open with the car, or at least the HVAC fan, off?
View 4 RepliesWinter is around the corner and I would like to remove the chrome covers off of my 04 factory rims, the rims are rusting underneath the covers which is forcing my center caps to pop off randomly. Also I was going to get new winter tires so while they rims are off the tire i figured I would Paint them black to match better than the chrome. How to get them off easily? Also a good paint that wont chip easy when i paint them.
View 6 RepliesThe fabric has been falling off most of the interior pieces, so I figured I'd start with trying to reglue the fabric on the A-Pillars. I searched the topic & found threads that said to remove the airbag emblem by prying gently, then remove a screw behind that. So I gently remove the emblem & find I have snapped off the 2 posts holding it in place, & there is no screw behind the emblem. What is the removal procedure?
View 24 RepliesHow to remove the plastic engine cover that covers the engine? I'm know some of them are just held in place with friction plugs and only require a good tug, but I've thought that about other things in the past which have resulted in expensive noises.
View 8 RepliesMy 06 F250 crew with the 6.0 starting blowing the cold AC out the defrost vent and will not switch to the dash vents. It's goning to hit 108 today and stay around 105 for the rest of the week.
View 14 RepliesHow to remove the front and back side marker covers?
View 14 RepliesI have to once and for all try to figure out what the heck is up with the AC and the defrost/vent switching back and forth. I have searched and searched and posted a few months back as well. But now that it's summer and 100 degrees out I've had a chance to test some more.
1 - I replaced both hoses going to the hubs up front.
2 - I am not sure how to test vacuum, but I did cap the hoses that lead to the hubs and still had the fluctuating back and forth
Looking for detail how to test for vacuum leak with a gauge directions ? What number is supposed to hold on the gauge and for how long etc...?
3 - It used to be that when I got to a high speed or RPM it would shift to defrost, but now I've noticed that once on the freeway going to work for instance and doing a constant 55-65 ( sub 2k rpm ) for about 20-25 minutes the vents hold fine. When I start to stop and go with higher RPM's it starts to 'break down' again. Could it be that there is a vacuum canister or pump ? I don't know ?? The diesels have a vac pump - do the V10's ? What can I check if there is no vacuum leak - what's next ?
My 2006, King Ranch, 4x4, 6.0's air conditioner only blows from the defrost vent. I have done some research on here, but haven't seen anything that identifies as a common problem. I did however, notice that this problem is stemming from a vacuum issue.
View 10 RepliesMy husband and I have 3 Excursions, V10, 6.0, 7.3 and I have a 6.0 250 crewcab. 3 of the 4 now blow air or heat from just the defroster unless your going at a slow speed.
View 2 RepliesMy buddy has a 97 f350 with a 460. When he accelerates his HVAC changes from vent to defrost then back when the desired speed is reached. What can be causing this?
View 1 RepliesMy 99' started o blow air only through the defrost vent today, and won't go through any of the other vents. I think this happens when your vacuum pump goes bad or there is a leak, correct? If so, how can I test these to figure out the problem.
View 2 Replies2006 F250 5.4 - While driving ac changes from vent to defrost on it own..let off gas and it will change back to vent. I replaced vacuum can under hood.. no luck.....
View 1 RepliesI have a 2000 f250 4x4 7.3 diesel. I had problems with my a/c and controls for sometime now. my a/c was blowing threw the defrost vent. I was told my blend door was bad. I bought a new blend door installed it,still doing the same thing. I was told to check my vacuum lines. I check them, they were bad. I replace my vacuum lines and my vac pump as well. that fixed my problem blowing threw the defrost vent. I can control my air flow from floor,dash vents and defrost vent. the problem I have, I not able to control my temperature when I turn my center from red to blue. It blows hot air and the air that is coming out of the vents isn't very strong at all.
View 1 RepliesThere is always something.... I just drove my girlfriend's new 2003 ranger edge home from the seller. Real nice truck. I noticed the heater selector doesn't change the air flow. It is on full blast for the defrosters, and is also trickling out of the floor and dash vents. No matter where you put the selector, thats the only place the air comes out.
The temp control seem to work OK, when you turn it on cold, you get cold air and visa versa. Even on AC and MAx AC... air out the defrosters. It's cold when you turn the temp control to cold.
I did some searching here and gather some info on checking the vac lines etc. Everything looks in place but one detail. The vac ball under the hood under the air box has 2 ports on the front end, and only one grey line going into it. The other port has what looks like a rubber boot and part of a very short vac line broken off it.
I looked, I cant find any loose vac lines. I'd like to know if this second port is suppose to have a second line on it, and where does it go? What color is it? Is this the reason the vent selector isnt working?
I have a 2012 F-350 SRW with a 6.7 diesel. The other day I went to push the defrost switch and noticed it does not work. All the lights work in the switches, and the temp control works, but no matter what I push, defrost or floor, it stay in the vent only. Anything I can check??
View 1 RepliesI have a problem with my vent selector on my truck. It's a 2005 f350 lariat. The vent is stuck on defrost, some times after a few mins I can get it to switch to floor but not always. I have replaced the pump, checked tank for cracks, disabled and plugged the auto hubs. The pump will shut off so I assume it's not a leak. I believe it's in the switching unit, can these be repaired? I found a lot of dust and dirt in the vac tank that had been sucked through a bad hub. I think it may need to be disassembled and cleaned. I have seen videos showing how to replace the orings in the older units. Are the newer style remote ones the same?
View 5 RepliesWent to use my windshield defrost this morning on my way to work. everything went fine. Leaving work I selected the face vents with my AC on and it only blows hard from the windshield vent even though its already been depressed.
View 4 RepliesSo my defrost works and my floor works but when i put my heater on defrost/floor mix it only comes out in the floor not the windshield.
View 9 Replies