Ford F-150 (2004-2008) :: Misfire And Rough Idle - EVAP Sensor
Feb 12, 2016
My 2004/ 4.6L F-150 had misfire issues and rough idle. Since changing the plugs and a COP the idle is better. It seems to stutter a bit at low RPMs around town, but it fine at higher RPMs. What to check next. Also since fixing the misfire and clearing the codes from the computer it won't enable all the emissions monitors. I've drive over 100 miles and the EVAP monitor still isn't on. The truck has about 213K miles on it.
View 3 Replies
Advertisement
I hopped in my truck this morning, fired it up, and it idled nicely. I drove around the corner, and noticed that the truck was barely responding to the throttle. Then things got shaky. It was a very rough idle, almost like a misfire. But I managed to get the gas to respond and got the revs up to about 3K and it seemed to run smooth.
No CEL either. Currently, I have no place to really look at my truck as I don't have a garage, or driveway for that matter. I don't have a scanner that can read live data either. I'm limited in my tools currently as well.
View 3 Replies
2004 Ford F150 5.4 Triton 3V Vin5.....
How this started, Drove through a lot of water as our City was in a flood on my way home and and the truck started running rough and got worse over time, I can now barely get to 40 mph as it starts to ping and sputter with no power.. the truck has been parked and not driven while in the shape it's in.
The truck keeps giving me error code P0303 Cylinder 3 misfire detected, P0174 System too lean (Bank 2) and at times another error P0300 saying multiple cylinder misfires detected.
After clearing the codes, I got new codes stating Misfire on Cylinder 2, 3, 4, 6. System too rich (Bank 1) System too lean (Bank 2)
Cleared the codes again and I'm back to Cylinder 3 misfire and System too lean (Bank 2)
What I have done so far... All repairs with in a few days...
1. Changed all spark plugs.
2. Changed all Coil Packs.
3. Changed number 3 fuel Injector.
4. Changed the Oil and Filter. (no water in the oil)
5. Changed the MAP Sensor.
6. Changed Bank 2 O2 Sensor 1 and 2.
7. Loosen the Catalytic Converter on the drivers side to re-leave back pressure thinking the Cat was plugged, still loss of power. I also drilled a small hole in the exhaust at my lowest point to see if it had water in it and it does not.
Checked for vacuum leaks using starting fluid around the intake manifold, no change in idle.. I also checked to make sure the vacuum line was still connected on the back of the intake manifold, I have found nothing leaking.
I also had cleaned the throttle body and changed the throttle position sensor.
Repairs within the last 6 months or less...
8. Replace passenger side cat.
9. Replaced both Bank 1 OS Sensors
9. Replaced Timing chains, Gears, Guides, Guide Tensioners, Oil Pump and pickup tube, Water Pump.
Cam Phasers are fine.
And number 3 coil is getting spark I changed the Ignition Coil again thinking maybe another bad pack.
Still #3 misfire and System too lean (Bank 2).
I am at a loss and not sure what to try, except for a compression test on cylinder 3 but I honestly don't think it's compression or a burnt valve.
View 12 Replies
2005 Ford F150 lariat 5.4
I had a misfire under a bit of a load (acceleration) and up hills. I changed spark plus with OEM Motor craft ones, truck ran super nice for a couple week.
Had the engine light flash, slow down and the RPM go up a tiny bit then back down and the light goes off
Now I'm back to miss fire different location, and a rough idle. I've swapped coil packs around and the miss fire stayed on cylinder 4.
Spark plug screwed or injector or ?????
View 14 Replies
5.4 3v. my last few weeks have not made me a fan. Here are the details:
I bought a 2008 F150 XL 5.4 3v with a cam phaser knock. Have done other timing jobs in past with no trouble so I was not too afraid to tackle this one. famous last words...opened the motor (shout out to the passenger side valve cover and its designer here) and found semi damaged roller follower on driver side. Worn cam lobe on the corresponding lobe and a loose chain on passenger side. proceeded to :
Change all timing components: phasers, chains, tensioners crank sprocket, all applicable bolts and BOTH cams as well as all lash adjusters and roller followers. most looked fine in fact all really did with a bit of wear on a few roller followers but only one bad one. engine didn't look to bad pretty clean.
Double and triple checked my timing chains and it was spot on. dark link on spot on crank, two dark links on the L and R dead on. put it back together. oh yes, changed all plugs with motorcraft ones, didn't even break one. did not change vct solenoids because I falsely assumed I could change the later easily if needed. they looked ok. screens intact etc... silly me for not realizing how kind Ford was in 2007 and later to necessitate removal of valve cover. I was reading a previous one on the how tos and assumed later models would be the same since it was the same sensor...
Cranked truck ran great. I mean perfect. sounded perfect. ran like a scalded cat. till it got to hot idle then it started doing its thing. rattle shake till you revved it. ran fine just wouldn't hot idle fine especially in reverse or under slight load. replaced driver side vct since ford only had one and I started on the easy side ordered the other one waiting for it. seemed to improve dramatically meanwhile I am driving this truck to test it. I drove it to work 50 miles each way and it ran great.
After a few trips it popped the P0420 light, seemed to run ok, cleared it watched it wouldn't come back. O2 sensor did seem to imply a bad cat on bank 1 since it seemed sensor two was mimicking sensor one and not staying stead like the other bank. still ran fine,
So I decided to check back pressure on the cat. I pulled sensor one out of bank one (really a joyously tight squeeze in there) hooked up my gauge and got 0 back pressure. revved it and all nothing. hooked sensor back up pulled truck out of shop and it commenced to running like crap. I mean bad. running worse than before I got it. Popping P0012 code continuously, and tons of misfire codes associated with bank 1 ..cyl 3 etc.. I tried swapping coils, pulled coils and checked spark with a tester and firing away looks like tons of good spark.
Now the weird part is : looks like bank one is dead. I can unhook any coil pack and/or injector and it runs the same and sounds like it is missing. if I unhook one off of bank 2 it almost dies or does. so bank 2 seems to be running fine. it will start and run but sounds like it missing sets flashing check engine light and backfires and stalls like crazy. I even second guessed my pressure gauge and unhooked exhaust manifold from pipe and it sounds even prettier when it backfires out of there but no change. I pulled cam sensors and cleaned it again and even tried swapping them since they looked identical but no change so I put them back.
Now I can only surmise that I am out of time somehow? or I have a gremlin perhaps? I like working on cars (usually) but this one is getting old. how do I verify what is wrong. if it is timing related how do I verify that now definitively once my marks moved I really cant figure out how to tell if it is in time? Since it has all new parts and they all ran beautifully till now. could it possibly be the vct solenoid doing all this? I plan on changing it when it comes in but surely it cant cause this many problems.. I unhooked it no change, and it does it at a cold idle and any rpm. really runs worse at idle but bad at any rpm.
View 3 Replies
Have an 06 F150 5.4 3v with no power. spark knock. rough idle. wants to die while driving, and random misfire code. Have replaced fuel pump, filter, coils and plugs. What to check next? Already thought of EGR - it doesn't have one.
View 4 Replies
My g/f's 2004 Ford Escape (3.0L V6 AWD 112,000mi) is acting up. After a full day of sitting, with the second half of it raining steadily, she was driving her Escape and it was acting funny (miss-firing, she said). The engine light came on and soon began blinking. She got to my house shortly after it started this. We left it and I drove for the day. Later that night, I drove it and it seemed fine. The engine light was on, but not flashing anymore.
The next day I took it my friend that was a Saturn mechanic and now working at a KIA dealership (same owner as the former Saturn and current Buick/GMC and Chevy Dealer). It ran fine for me. So he tries to scan it, his Mac Tools scanner won't read it. The KIA scanner wouldn't read it. I drove it the Ford dealer up the road. They said they couldn't get to it until after lunch, I just want the codes read. They re-iterated, and I told them to pound salt and went to an independent shop where I know a guy. They read it right away for me. "Mis-fire on start-up" & "Cylinder 4 Mis-fire." were the two codes stored. He cleared them.
She got the tune up basics (plugs, wires, air filter, etc) and did the complete tune-up herself yesterday. (I was impressed). She put 94 in the tank and some fuel system cleaner in it as well. She said there's been no change and today I finally saw what it was doing. Sometimes during idling at a stop light, the RPMs will drop to almost zero, the lights dim but so far it has not stalled. It'll do this for several seconds, then correct itself and idle normally.
Currently, the engine light has not come back on. She's thinking coil pack (each cylinder has a coil on these engines) on #4. She wants to switch it out with #1 and see if the problem follows. I think that might uncover the cause, or it could be the battery. It's the original, never been replaced and has a lot of miles on it, but it survived this past winter, without trouble. In my experience, most batteries crap out due to age in the fall when the cold snaps start.
View 11 Replies
I have an 05 F150 with the 3v 5.4 with 170k on it. Last fall we changed the timing chains, cam phasers (aftermarket), plugs, coils (OEM), VVT solenoids (OEM), Cam Position sensors (OEM) and swapped in a GT500 oil pump. Recently under moderate load (fairly heavy acceleration onto the freeway, pulling a large camper) I get a pretty rough misfire. Tonight I pulled the codes and it was Cylinder 5 misfire. In the past I have also had Bank 2 Over-Retarded code. What are the next things to verify and check? I plan to clean the throttle body and change fuel filter but I'm not sure either of those would cause the misfire code?
View 3 Replies
After scouring through hundreds of threads on this forum (which is Awesome, BTW), it seems as if this misfire / rough idle thing is fairly common (which is scary!!). CEL is on steady. Had the codes pulled; P0301, P0302, P0303. At the recommendation of the mechanic, I had the plugs replaced...no improvement. He then replaced the ignition coils...no improvement. Just finished replacing the MAP sensor. This actually had a VERY temporary positive effect. However, after about 5 miles of driving, the misfiring returned. Took the car to the Hyundai dealership, and they acted as if they didn't want to fool with it. They referred me to a couple of local repair shops...????
View 8 Replies
I just bought a 2007 F150 XLT with a Triton 5.4 with 80,000 miles on it. My problem is this, the engine seems to run ok ( a bit rough) until it gets up to running temp and I have driven about 10- 20 miles then most of the time, it starts to act up.
When I am driving it is fine, but when I slow down and come to an idle about 500rpms, it sometimes runs very rough, sounds like a diesel and shakes violently. It feels like it is doing damage. Sometimes it stalls. If I rev it back up immediately it will smooth out.
In speaking to some friends they've suggested things from plugged oil channels, (affecting the cam phasers? All the way to it needing new chains, phasers and guides. I don't want to spend a ton of money doing an improper service repair only to have the issue show up later . But there seems to be a lot of different answers to the same problem. Is the dealer going to be able to diagnose something like this fairly well? Or should I try to narrow it down a bit first?
View 2 Replies
I own a 2007 prius, it has about 320,000 miles. It has recently been diagnosed with a #2 and #4 cylinder misfire. The car severely idles rough, but when getting in the gas it goes away. I have replaced the spark plugs, the old plugs were very white(lean), replaced fuel injectors, used fuel injector cleaner. I've sprayed carb cleaner around the intake to see if I might a leak--no leak. The motor uses about a quart of oil every 1,000 miles since about 100,000 miles. I'm just guessing, could it simply be low compression causing this? I pulled the new spark plugs after about 5,000 miles and they where white also.
View 9 Replies
My wife's 06 expedition 5.43v runs rough loud and dies. Not all the time just when it's to hot. I got a code it's p0022 cam sensor. I changed both started the rig up and heard loud rattling like metal maybe chain. It lasted for a the length of my video 1.4mins give or take then went fine, i turned the car off and back on everything seems fine. I know I got her oil done after driving. She had metal/plastic in her oil. I had all plugs done and actually i re did the 8th cylinder plug because it was miss firing and i pulled it by hand with only the socket no ratchet. I'm thinking the chain is going bad if not already bad. Only 113k miles my 04 f150 5.43v lasted 250k before motor swap...
View 7 Replies
Im trying to chase down an engine miss fire on a 2007 with the 5.4L. It only seems to miss under no-load conditions, such as at idle and on a downgrade while driving. Acceleration and under a load it runs fine. New Champion plugs were installed at 135,000 miles. The truck now has 150,000 miles and has only been miss firing for the last 1,000 miles or so. I pulled the connector off of the coils one at a time to try and figure out which cylinder/s were missing. I thought I found the problem ones and replaced two of the coils, but it ended up not fixing the issue. Ive tried spraying carb cleaner at and around the intake to check for leaks, but found none. I have a scanner, but the check engine light is not on, so its not much luck.
View 5 Replies
I have a 2006 f150 I just bought after my F250 was stolen. It has about 70k miles. It has been running pretty rough ever since I got it. It finally threw codes so I tried to address all the issues. Changed out a couple coils and all the plugs (motorcraft platinum). The camshaft sensor was also bad. Truck runs much better but still has an idle issue I cant seem to nail down.
I assume its something to do with air intake. It doesnt happen all the time. It runs rough and knocks and sometimes dies. If I give it gas it stops. I read it could be the idle air intake valve, but then I read that this model doesnt have one. I also read that air intake issues dont normally throw codes. Are there any common problems I could look for? Would cleaning the throttle body do any good?
I know the basics, but this kind of thing is tough for me to troubleshoot. You may have already seen me post this problem, but I didnt get much response so I thought I'd try one last time.
View 11 Replies
Ok, so I just replaced the entire timing set (phasers, chains, sprocket, tensioners ect) on my 2004 f150 5.4l about a month ago. I also extracted ALL 8 spark plugs and replaced those with the Champion 1 piece plugs. In addition, I replaced the intake manifold because I did this job when it was 20 degrees outside and I found a crack. Soooo, all that being said I put the whole truck back together and it runs like New. Until about a month later. When the engine gets hot, maybe after about a 30 minute drive or so, it has a really really rough idle until I give it a little bit of gas. Then it clears up. It has only done it 3 times since I put the engine back together. It might go 2 weeks and not do it. No codes. What I could be? EGR? MAS air? Only other thing I can think to say is if you get on it out on the highway, after about 3k rpms it seems like the power drops off quite a bit. Like the engine isn't getting enough fuel. I guess it could be just me, but it just doesnt seem right.. I guess I could try to unplug the MAS air flow sensor...
View 14 Replies
I have 2008 f150 with 5.4 and 54000 miles. It has a bad vibration or rough idle only when AC is on. When AC is off it runs very smooth. Runs great while driving with AC on. Tensioner pulley was moving a lot more than normal when engine started vibrating so i replaced it and the belt but it didn't work. I also checked the other pulleys and they are good.
View 1 Replies
Is it possible to have an intermittent injector problem I am having the same problem with my 2004. Its not all the time its rough only at idle constantly. If I keep the rpms up it doesn't do too bad...
View 1 Replies
An injector stuck open on my 05 5.4 and bent a rod. I had a new rod put in and all new revised Motorccraft injectors. This was about a month ago. Truck has ran great for the past 3 weeks until today I put it in park and it idles real rough, put it in gear and it smooth as butter again? (Once in a rare while it will continue to idle rough in gear for a few seconds but then clears up.) New motorcraft plugs were put in right before it bent the rod. The truck runs real strong other wise. I am about done with ford this pickup has been the biggest pile I've ever owned one thing after another and just when I think its fixed its some other stupid problem. I'll start by cleaning the maf and throttle body. Could it be a bad coil?
View 3 Replies
I purchased an '08 F150 about 6 months ago, and have a problem that two mechanics haven't been able to solve. The truck has a 5.4L engine. Unfortunately, I bought from an auction and the 30 day warranty expired before I realized the problem.
After a longer drive (30 minutes to work) the engine is warm, and I always back into my parking spot or driveway. In low gear, it begins to idle very rough and the engine shakes. If I leave it long enough, it will stall. Usually I pop it into neutral, give it some gas, and its fine. I just bought a camper trailer, so I'll need to use the lower gear when backing up.
So far, the engine has been flushed twice, the solenoid replaced and phaser replaced. The second mechanic has recommended I contact a dealer, but haven't had luck with them with my previous Explorer. What it could be? I will be getting the diagnostic paperwork this week.
View 14 Replies
I have a 2005 5.4l f150. 105,000 miles. Recently While on a trip I experienced rough idle and stalling at idle. I drove it home 2hrs. The ride home was challenging. Poor acceleration, rough idle. Took it to the dealer and was told I needed plugs and I was 5qts low on oil! Not sure where the oil went. It hasn't been leaking and never seemed to burn oil in the past. They did the tune up. Picked up the truck. It ran fine while cold. Upon warming up it ran rough at idle and stalled just like it did before. Took it back, they said "you need a new engine. Upon warming the oil pressure drops indicating internal engine damage". I took it to a local guy he says replacing the cam phasers might fix it. What's the consensus, should I try the cam phasers? Look for some other potential problem or trust the dealer? (They did refund me for the tune up)...
View 14 Replies
2005 f-150 4.6l v8 rough idle only when truck is to normal operating temp. I have run several gas system cleaners through the truck. I replaced the air filter, the fuel filter and the spark plugs. I am only getting 14to 15 mpg mostly highway. No DTC's are showing up. The truck only has 50,000 miles.
View 6 Replies
