I got an 08 F150 2wd. I noticed lately a mild roaring noise coming from right front wheel, but it only does it when I'm turning left. There is nothing while driving straight or during right hand turns. Only happens during left hand turning.
View 1 RepliesI gotta a roaring noise coming from my right front while turning. Planning on replacing just the wheel bearings tomorrow & not the whole hub assembly(2008 2wd). Is there a thread that lays out the steps and other parts I may need? I've seen alot different stories on the net on how to do it. Everthing from I can press new bearings to I have to do 4x4 hub conversion. Seems to be some confusion.
View 2 RepliesI owned a 99 f250 a little while ago. Just bought a 2006 crewcab F150 xlt about 2 months ago, and for the past month there has been this unusual grinding or whirring like noise coming from the front passenger side wheel.
I took it to the mechanic and he found a bad wheel bearing on drivers side and replaced it but that wasn't the issue. He could hear the noise but wasn't able to figure out what the actual issue was.
The noise only happens when my foot is on the throttle. (not when coasting) and i also just discovered that it doesn't make any noise at all when put in 4x4.
I have a 2002 GMC Senoma 4WD. I have recently noticed a roaring noise in the area of the left front wheel, The noise is associated with rotation of the wheel. There is no unusual tire wear or shimmy. I rarely use the 4WD however when I engage the 4LO option the noise gets louder.
View 3 RepliesI hear a roaring noise coming from the front of my 2003 Jetta. I know it needs some kind of front end work, but I am not sure what. The front passenger side tire also wore badly and prematurely on the inside and outside.
View 8 RepliesI have a 2009 Sonata (4 cyl) with 110,000 miles.I have a loud roaring noise coming from my right front end. Jacked car up several times, all seems very tight and wheel spins smoothly. This has been going on for over 5000 miles and I have been waiting for the ailment to show its self more clearly in order to diagnose. sound does not change when turning in either direction or breaking. sound increases with speed and is quite loud at 55mph. Had to replace a tire and put it on the right front to see if it was tire wear and there was no change. sounds like loud road noise.
View 2 RepliesI have a 2005 F150, 5.4 triton. I bought the truck used and it came with an Edge tuner. It's lifted with 35's.
Under mild acceleration I get a psst-psst-psst-psst-psst-psst type noise. Sounds almost like air... It only happens in drive when you get on the gas and put a load on the engine but not always. It doesn't seem to happen if you mash the pedal...
I can't seem to replicate this sound in the driveway. I've never heard this sound before.
The front of my truck is making a roaring noise after playing in the mud while your going down the road is the only time I hear it. It sounds as if I have really aggressive tires on it. I did do my best to clean out from under it... It doesn't seem to feel like its dragging. 4x4 engages fine? I mean it started only after a few days of playing in it, I didn't wash the mud off right away. Should I be concerned? I mean if its just some dirt up against something, then that is no big deal, but my ranger whined when it was low on differential fluid. However its not whining, just roaring.... Should I be concerned? Truck drives fine... no issues there.
View 5 RepliesMy 2008 F-150 recently started making a funny noise from what seems like the front right wheel.
The weird thing is that it will only make the noise while accelerating. The second i take my foot off the it stops. Also, the sound stops if i put it into 4WD and does not happen at all in 4WD.
It has nothing to do with turning or breaking. It only makes the sound in 2WD while my foot is on the gas.
The sound is kind of weird. It sounds like something is loose, and it sounds similar to tin vibrating on metal.
At first i thought it may have been heat shielding rubbing on something, I checked under the truck and found nothing loose.
It's weird that it only happen in 2wd yet in the front end.
Someone had mentioned that it may have something to do with the fact that there is no torque on the front wheels in 2wd and when i put it into 4wd it put torque on it, whatever might be loose then becomes tight.
My wife just bought her first truck, a 2008 F150 about a month ago. We have been driving it around since then and love the truck. The only real problem that I have seemed to encounter on the truck is a squeak coming from the front left wheel area. I can hear it when I cut the steering wheel and when I hit a big bump/pothole in the road. My dad and I have looked into it and he thinks that it is probably the axle joint where it goes into the steering knuckle/spindle. If it is this axle joint, is there a way to service/grease it and go on, or will it just simply need a new axle shaft?
View 1 Replies2008 2wd 4.6L 98K miles F150 for the past few weeks has been humming with a rhythmic vibration which feels like it is coming from driver's side front wheel. It doesn't do it constantly, nor at all speeds. Once I hit about 25mph, you can start to hear a humming. At 35, slight vibration. Between 50-60, heavier vibration. Sometimes at 65+, it subsides quite a bit. Both front rotor assemblies are newer, and I put in a brand new left because I thought it was a bad bearing.
View 5 RepliesMY '07 SuperCab just started making a strange rhythmic sound as I drive. It is coming from the drivers side front wheel area. It is like a short creaking sound. It stays the same if I am turning the tires. Seems to go away if I put the brakes on hard, but I slow down so much I am not sure. Front CV Joint?
View 1 RepliesAlright, so about a month ago I was driving when I heard a terrible noise sounded like a pop can stuck between a bike tire coming from the front end. I figured this was the dreaded noise most folks hear when the 4wd system isn't getting enough vacuum.
It did this for about two days, even after replacing the IWE solenoid, then it just stopped and I haven't heard it since. Me being on the cautious side, I'm a bit worried. I haven't jacked the truck up, but I did (brace yourself) lay under it while my buddy drove slowly over, there was no unusual movement.
Question is, if I had to replace anything, what exactly would it be and how much am I looking at? My warranty will be up in about a month or so and Ford has been less than spectacular with repairs thus far so I'd like to go ahead and fix it myself
I recently installed a 2" aluminum HBS leveling kit on my F150. ('04 FX4 SCrew, 5.4, 61K miles). I was excited to finally improve the truck rather than fix something. The install was straightforward and I didnt have any issues (other than Cleveland, OH rust).
After installing the kit I noticed a whirring noise coming from the front end while driving, but I didnt think much of it and I got an alignment a couple of days later. Immediately after the alignment, the problem is still there. It sounds just like aggressive mud tires driving down the road, so I think it is coming from the tires.
The noise follows the speed of the truck (the pitch gets lower as you slow down) but you cant really start to hear it until you slow down below 45 mph. It is much more noticeable at lower speeds (probably because of the lower wind noise in the cab). I dont think it would be a CV joint/axle issue, but who knows. I am considering taking it back to have the alignment checked, but I figured I would check on here before I do.
I just bought this truck last fall, and it is one step away from being traded in because of the countless nuances this thing has (wet floors and consequently rust everywhere on the inside of the cab, rattling window trim, shaking bed, squeaky rear window, noisy phasors).
I have a 2005 ford f150 supercab 4x4, and around feb I replaced all the ball joints my self, and now recently when back with the wheels turned turned to the left and then put it in drive and turn the wheels all the way right and give it has to take off there is a popping noise that comes from the driver side front wheel and it just does it once I take off and quit . I've looked and everything and cant see anything that would cause this. And know when I put it in park and it rolls forward I can hear a popping noise that sounds likes it coming from the rear end. I had my rear rebuilt, with new pinion bearing and race, a new axle on the pass side with bearing and the shop told me that it the driver side is questionable on the axle but it has new bearing also, they also told me that it needs a carrier case cause it had groves wore in it where the axle bearings wore out so much. at the time I could afford to have them to replace the carrier case. what would cause the popping from the front end and now the popping in the rear end.
View 1 RepliesI have an intermittent grinding noise coming from what sounds like both front wheels, it sounds like metal on metal almost like something metal rubbing the rotor but I just put new pads on and the noise was there before as well with nothing touching the rotors but the pads. The sound will appear out of no-where at low speeds of 35 or below and will continue until I brake and slow down, just before I come to a compete stop the noise will stop with a slight clunk.
I can then drive away with no noise. I am pretty sure it is not brake related except maybe ABS somehow but was also thinking front axle or diff, also have read posts that are bearing related, but both at the same time?. It is the slight clunk before stopping that I can not figure out is related to. It is an 05 f150 xlt 5.4 super cab 4wd with 85k miles
I've got a 2008 santa fe limited 3.3 awd with about 170000 km on it. Lately when I brake I've been hearing a clicking noise coming from what sounds like the driver side front wheel area.
Had it in to my mechanic who checked the brakes and said that pads/calipers/rotors were all fine. They replaced the passenger side front bearing on the lower control arm a few weeks ago and said there is no play or noise coming from any other suspension components.
Where to look next? My mechanic isn't sure what it is so I was going to take it to the dealer and see if they can fix it. Also had new tires installed about a month ago
I have a 2007 impreza not wrx or sti and I am hearing a roaring sound coming from the front end.
It has 65k on it and my wife drives fast and hard.
First issue started a few weeks ago. When turning left at a speed > 20mph or when turning wheel quickly I get a rattling noise, which is more prominent with the driver window down, so it sounds like it comes from the driver side front wheel, but not quite sure. It is fairly loud as I have had pedestrians look at my car when turning because they can hear the rattle.
Second issue started this morning but has persisted every time since. When the car is cooling down, we get that whirring noise, which I presume is thr coolant pump. That noise also happens now when I enter the car, and it is accompanied by a knocking noise as if somebody is hitting the outside of the car repeatedly. This is quite unnerving as it sounds like something is hitting the bodywork of the car. It stops immediately when the normal whirring stops.
I had the steering and water pump recall done in november last year, could this be related to that? Forgot ti add the car has done 49000miles....
Over the past few months I've noticed that my truck has a very intermittent shudder under mild acceleration. If I accelerated more during the shudder it seemed to disappear until I let off the peddle a little. When it happens the truck doesn't seem to be lacking power and the engine throws no codes. It happened again today right as I had stopped at a red light. I noticed that it was shuddering at idle too. I shut the truck off at the intersection and the shudder was gone once restarted. What it may be?
View 5 RepliesOn my 96' Explorer 4wd, 4L V6, auto tranny the front end makes a roaring noise when slowing down from 30mph to stop; no shimmy or shake or any other noise, it has 133K miles on it, original wheel bearings; just wondering if it is wheel bearing assembly and are these pressed on or can you remove them and replace with new assembly fairly easily. Are there any threads with the procedure here.......
View 11 Replies