Ford F-150 (2004-2008) :: MIL Light Started To Flash / OBDII Codes / Misfire
Dec 16, 2016
My wife was driving her truck yesterday and said the MIL light started to flash and the truck felt like "it was about to blow up" . So when I got home I busted out the trusty old scanner and this is what I got:
P0305- Cyl 5 misfire'
P0354- Ignition coil D primary/ Secondary circuit malfunction
P0304- Cylinder 4 misfire
The truck is a 2005 5.4 with ~130,000 on it and it runs very well for the most part. I have done the spark plugs before the summer and replaced them with the motorcrasft sp-515s. I am guessing the problem will be with the #4&5 coil packs. is there a way to troubleshoot these?
View 5 Replies
Advertisement
I changed my sparkplugs and coil packs last month. Was getting CEL light but it would go away after a while. I figured out that I had gapped my spark plugs way to small (almost touching) so I took them out two nights ago and regapped/ reseated them.
My car was running fine yesterday, but today when I started my car up, the engine was shaking a lot for about 10 seconds and the CEL was blinking. After 10 seconds the shaking and CEL went away...
It drove fine. I'm just wondering what could be throwing these CEL's and causing the shaking? Plugs are gapped to 0.32
Also, I had my timing belt and water pump replaced almost two weeks ago now. Any chance that could be lending to the problem?
My guess is that one or more cylinders are screwy. I'd rather not bring it into the vw mechanic since I'm tight on cash.
View 6 Replies
I have a 2008 Accent Hatchback with 130k+ miles. I got a pretty good deal on it from a fellow who maintained pretty good service and had installed an aftermarket air intake (well, he removed the stock one and put a small, roughly 4" diameter, filter that is open to engine compartment) and all looked pretty good.
At the first fueling, I noticed issue - I had to rev motor for about 30-45 seconds to get it to stay started. Figuring it was an evap issue, I replaced purge valve and gas cap (cap was obviously loose). This did not correct the problem. I did not worry about it to much because with that exception, the car drove wonderfully back and forth to work, etc.....until recently.
Car started "jumping" and being sluggish. Codes came back as random misfire. Plugs and wires are only a few months old. I wondered if it had something to do with fuel so I ordered filter and pump (figured i would replace both since I was going to be pulling top off tank anyways) - this is going to be my project for the day.
Here is the kicker though : I noticed in the past day or so that car has been okay on my short commute to work in the morning and back home in evening. When I went to store midday and was parked on HOT pavement, I had issues right away. Car is very temperamental as the temperature increases. My wife also noted that last night while driving about 15 minutes away that the engine wall was hot enough to be uncomfortable to the touch of her bare foot and issues were abundant.
Once I get to speed in 5th gear, I seem to be okay, no issues (yet). It is primarily during acceleration and mostly during low RPM (low for this car anyways which seems to run best at 2500+).
View 13 Replies
I have a 2005 F-150 W/ 5.4 triton, and am having multiple codes. They are:
P0172- System to rich(Bank 1),
P0174- System to lean(Bank 2),
P0300- Random misfire,
P0303- Cylinder # 3 misfire detected,
P0304- Cylinder #4 msfire detected.
View 2 Replies
I have a 2006 Lincoln Mark LT that seems to have an intermittent misfire. The truck is not throwing any codes either.
View 6 Replies
I am perfectly capable of doing the repairs just short on time. the only shop in town is booked out 2 weeks, i need my truck sooner. 2006 f150 5.4v 3v 168k. I bought it with 150k and it was clean and ford maintained from the original owner. for a while it has been fluttering from time to time during acceleration. last week it started shuttering and missing around 45 trying to accel. no cel. I've read and actually fixed my freinds 08 but replacing cop and plugs. I bought motorcraft plugs and granatelli coils. friday morning it didn't want to start, cranked for a bit then locked up, as if hydrolocked.
I let it sit 5 minutes then cranked again and it fired but hesitating and missing like never before. anything passed 3k rpm it ran good no load. i had to drive it and it doesnt want to shift properly, revving way past normal shift points. smoking alot more than normal. hard to tell being 5 degrees out. finally got some codes. bank 2 sensor 1 stuck rich 4 times lean twice. Saturday i changed the oil plugs. and coils plugs were not original but were worn enough to visually see. all of the passenger plugs were a nice brown color. all of the driver side were jet black of carbon which follows the o2 cel. i reset it with my glorifed code buddy and it took a while if at all to come back. so im thinking not an o2 sensor????
It runs rough and will stall from time to time, I am to the point where i wont drive it. i will be replacing the camshaft sensors and vct solenoids tonight, and that one 2 if i have time. from what I've read phazers will cause a rough idle but once under load at least have some performance. when i accel it the rpms stall out before a shift i cant get anymore power, say wont got over 3200rpm. when chains and guides need to be replaced whats the symptoms??
View 6 Replies
I do not know the 5.4l 3v as well as my last 360ci dodge. It's a 2005 F-150 SuperCrew 4x4, got it cheap, and it's got issues. Got codes for misfire on cylinders 4 and 5 and Coil 'D' circuit malfunction. Obviously it has codes for limited power as well. was wondering how cylinder numbering goes and what coil is 'D'.
View 6 Replies
My new to me 04 4.6 shuddered and misfired really bad last week, got couple misfire codes. I changed plugs which were really bad, like burnt out to .080, got a HEI ignition tester and got a healthy spark from all the coil packs. Drove it today and ran much better but still would shudder under acceleration when cold, wasn't as bad when warmed up but still noticeable. I thought if I got a spark with the tester that means the coil is ok? or is that not the last word in coil health. Or should I look somewhere else like injectors ? Haven't got any codes since plug change.
View 1 Replies
5.4 3v. my last few weeks have not made me a fan. Here are the details:
I bought a 2008 F150 XL 5.4 3v with a cam phaser knock. Have done other timing jobs in past with no trouble so I was not too afraid to tackle this one. famous last words...opened the motor (shout out to the passenger side valve cover and its designer here) and found semi damaged roller follower on driver side. Worn cam lobe on the corresponding lobe and a loose chain on passenger side. proceeded to :
Change all timing components: phasers, chains, tensioners crank sprocket, all applicable bolts and BOTH cams as well as all lash adjusters and roller followers. most looked fine in fact all really did with a bit of wear on a few roller followers but only one bad one. engine didn't look to bad pretty clean.
Double and triple checked my timing chains and it was spot on. dark link on spot on crank, two dark links on the L and R dead on. put it back together. oh yes, changed all plugs with motorcraft ones, didn't even break one. did not change vct solenoids because I falsely assumed I could change the later easily if needed. they looked ok. screens intact etc... silly me for not realizing how kind Ford was in 2007 and later to necessitate removal of valve cover. I was reading a previous one on the how tos and assumed later models would be the same since it was the same sensor...
Cranked truck ran great. I mean perfect. sounded perfect. ran like a scalded cat. till it got to hot idle then it started doing its thing. rattle shake till you revved it. ran fine just wouldn't hot idle fine especially in reverse or under slight load. replaced driver side vct since ford only had one and I started on the easy side ordered the other one waiting for it. seemed to improve dramatically meanwhile I am driving this truck to test it. I drove it to work 50 miles each way and it ran great.
After a few trips it popped the P0420 light, seemed to run ok, cleared it watched it wouldn't come back. O2 sensor did seem to imply a bad cat on bank 1 since it seemed sensor two was mimicking sensor one and not staying stead like the other bank. still ran fine,
So I decided to check back pressure on the cat. I pulled sensor one out of bank one (really a joyously tight squeeze in there) hooked up my gauge and got 0 back pressure. revved it and all nothing. hooked sensor back up pulled truck out of shop and it commenced to running like crap. I mean bad. running worse than before I got it. Popping P0012 code continuously, and tons of misfire codes associated with bank 1 ..cyl 3 etc.. I tried swapping coils, pulled coils and checked spark with a tester and firing away looks like tons of good spark.
Now the weird part is : looks like bank one is dead. I can unhook any coil pack and/or injector and it runs the same and sounds like it is missing. if I unhook one off of bank 2 it almost dies or does. so bank 2 seems to be running fine. it will start and run but sounds like it missing sets flashing check engine light and backfires and stalls like crazy. I even second guessed my pressure gauge and unhooked exhaust manifold from pipe and it sounds even prettier when it backfires out of there but no change. I pulled cam sensors and cleaned it again and even tried swapping them since they looked identical but no change so I put them back.
Now I can only surmise that I am out of time somehow? or I have a gremlin perhaps? I like working on cars (usually) but this one is getting old. how do I verify what is wrong. if it is timing related how do I verify that now definitively once my marks moved I really cant figure out how to tell if it is in time? Since it has all new parts and they all ran beautifully till now. could it possibly be the vct solenoid doing all this? I plan on changing it when it comes in but surely it cant cause this many problems.. I unhooked it no change, and it does it at a cold idle and any rpm. really runs worse at idle but bad at any rpm.
View 3 Replies
My 07 xlt 4x2 4.6 (49700 miles) started missing a couple of weeks ago. Did it for 2 days, the Check Engine light came on, then it quit missing and ran normal. CE light was still on, so I had the code read and reset light. Got two codes: ignition missfire #8, and rich fuel. I assume the rich fuel was caused by raw gas in the exhaust.
Anyway, the truck ran fine for two or three days then started missing again. Checked #8 by taking the wiring connector off #8 COP - rough idle unchanged. Pulled COP off #8 and #7 and swapped. Rough idle unchanged and confirmed miss was still #8 by pulling COP connector. With #8 connected, disconnected #7 (with COP from 8) idle was significantly worse.
Replaced #8 plug. Same miss. What to check next?
View 2 Replies
I have a 2005 F-150 5.4L 2WD 90K miles. I started getting a misfire and hard jerk when going uphill. No codes for a few days but misfire got a little worse and more jerking at full throttle acceleration or level throttle up a hill got codes p0300 and p0171. I replaced the fuel filter cleaned MAF and changed plugs Motorcraft plugs (none of them broke during replacement). Miss got worse. Missing at idle and no power 3K rmp to get to 40. Only code pulled was p0171. Replaced upstream O2 sensors and COPs. Will barely idle now. Dies when put in gear. Full throttle barely moves forward a few feet just sputters. Checked vacuum lines cannot find anything. Only code I get is P0171. Fuel injectors next? Or shop?
View 3 Replies
Apparently yesterday (no known reason) my sons truck started to develop a miss (so it feels like to me).
2005 f150 5.4 auto 215000km 4x4 stx. No specific cylinder codes. All general codes.
P1000
P1464
P1550
P1703
P1780
None of which I can see causing the miss. No check engine lite, no other codes. Not sure what to look at next. I am starting to disconnect the coil packs one at a time and see if I can pin down the cylinder.
View 4 Replies
I just put a brand new engine in my 2004 f-150 4X4. Truck ran fine for two days. Yesterday I started the truck as usual put it in reverse. As I was backing up it just stopped running no warning nothing just stopped. All electrical still working fine gauges radio etc. When I turn the key I get nothing no starter nothing. The security light continues to flash slowly even when the key is turned on. Basically the best way I can describe it is. The truck is acting like it is in gear when I turn the key. And the odometer reads check gauges.
View 4 Replies
What would make the OBD II not read the code that is set on my truck. It says "Communication Error..." Fuse 41 grants power to the Diagnostics port and the cigarette lighter. The cigarette lighter is working. Any other reasons I can look at?
View 3 Replies
My O/D Light flash some times, no codes thrown. What could cause it?
View 9 Replies
I am currently chasing misfire codes that started out on cylinder 5 p0305 was the first code I replaced spark plugs and wires about 200 miles the code returned checked coil with meter it was barley in spec. I have replaced coil same code only difference was a hard start cold or hot replaced injectors now hard start is fixed but logging codes for right bank is to rich and p0300 304 305 and 306 also performed compression test on right bank and readings are 155 155 and 160...
View 3 Replies
Experiencing a melt down with one of my trucks. One of our trucks is an 06 F250 SD with 80k on a 5.4L and the other day the tow/haul light started to flash. I took it to a buddy's repair shop (who is an experienced Ford tech and tranny guy) any way, it shifted fine until about the last 1/2 mile before I got to his shop, then it started shifting in and out of different gears. He found solenoid "A" pressure solenoid failure and one other solenoid failure, he replaced all 7 solenoids and also found the pigtail from the transmission to the wire harness bad as well and replaced that. I pick it up and get about a mile down the road and the light starts to flash again so I took it back, he ran his scanner and now found something with the coast clutch and through all his testing it told him the coast clutch needs replaced. He removed the trans. and tore it all down and found nothing wrong with anything, in fact he said everything looked in great shape and thinks the pcm failed.
View 12 Replies
I have a 2005 f150 4x4 with a 5.4 it was studdering on the highway under light load, i changed the plugs and coils it worked great for a day now working worse and giving a misfire #7, so i swapped the injectors around still misfire #7.
View 8 Replies
So I was cleaning the house and found a OBDII I was wondering how I can use it. Would the car still give me codes even if there is no check engine light?
View 6 Replies
I have a 2005 f150 with 96,000 miles. Long story short, last August I was headed to the mountains going up a steep long hill and the engine light come on. once i was over the pass the light went off. During my 4 wheelin' trip it never came back on until I was headed home and going over another pass and then it stayed on for a couple of days. I had it checked and it was a cylinder 5 misfire. I did some research and found that replacing the coil cover might fix the problem and if not the spark plugs would need to be changed.
I changed the coil cover, problems solved... until I headed to the mountains. light came on and then eventually went off later that day. I didnt think much of it. then a few months later i was headed to the mountains again and the light came on in the same place on the steep incline hill. I. took it back to the shop, same reading. I decided it was time to replace the spark plugs anyways so I would invest. I have new plugs and everything is good however, I had no plans to go to the mountains in the near future. Now, a few months later I headed to the mountains and crossed my fingers it would not come on but it did.
I've done the research again and it seemed like the coil cover and spark plugs are usually the cause of the problem...however I have changed mine. The light is now off again. I don't understand what is triggering the problem and what is really happening and if it is safe to keep taking to the mountains with this happening. I did notice that everything was fine at 60MPH but once i hit the hill and steeped on the gas to go 65 and hit 4-5RMP that is when the check engine light came on...
View 12 Replies
I have a 99 town car with 78,000 miles. I filled the tank and have run about 1/4 tank when the engine started to misfire. Got the Service Engine Soon light so went to O'reily. The OBDII code is p0306 cyl 6 misfire. What would you check first?
View 3 Replies
