Ford F-150 (2004-2008) :: Intake Manifold Replacement?


Jan 10, 2014

Looking for any pictures or directions on replacing the intake manifold on the 2004 F150, 5.4. Got all the parts with the pulgs, and ignition coils.

View 6 Replies

Advertisement

Ford F-150 (2004-2008) :: 2006 - Coolant Leak At Intake Manifold

I have a 2006 F150 screw 4.6 auto 116k miles that has evidence of a small coolant leak where the intake manifold joins the head. This is on the drivers side directly under the thermostat housing. The t-stat housing is dry and the hoses all appear dry. It's just wet right at the gasket where the manifold joins the head. Reservoir is still normal so it's not leaking too much just yet.

I searched this site and youtube but didn't find any other posts. Lots of problems with older trucks with composite manifolds but nothing for this one. It looks like a part of the bottom of the manifold is plastic but the entire top and where it is leaking is all aluminum.

It seems odd that this would start in the winter time just driving back and forth to work (no load). And, yes the antifreeze is good. Just wondering if this is a known issue with this truck. Is it just a matter of replacing the gaskets or is there some other flaw I should be concerned about?

View 2 Replies

Ford F-150 - 1997-2003 :: 2001 5.4L - Intake Manifold And Gaskets Replacement

I am about to replace the intake manifold and gaskets. I know all of that process, but first question is if there is anything i should do whilst in there. Second question; what can I do with my intake to get more power? Mainly just kind of wondering before I get my parts ordered.

View 4 Replies

Bonneville :: 1995 Pontiac GM 3.8 Upper Intake Manifold Replacement

Just today,when replacing the UIM on a naturally aspirated 95 Pontiac Bonneville 3.8 with a Dorman upgraded type from my local auto parts, I ran into an issue. When following specified torquing sequences and specs , be very careful with the 1 long stud (#7), as it will split your new manifold there if you try to torque to 89 in/lbs. Took 1st back for replacement ,and the second new one started to split at the same place. Was using a brand new Craftsman in/lb torque wrench set correctly and following instructions exactly. I've seen a lot of excellent info on this UIM issue with the GM 3.8 ltr 1995-2004 years, but never this issue with the replacement ones. If I have to change this again will definitely go with the aluminum one.

View 1 Replies

Monte Carlo :: 2003 SS - Intake Manifold Gasket Replacement

I took my Monte in for the annual Missouri Safety Inspection. Note: I had no known problems with my 2003 Monte SS 117K Miles. After the inspection, which passed, I was informed of a variety of problems: Intake Manifold Gasket Replacement, Valve Cover Gasket w/Intake replacement, Thermostat w/Intake Removal, Fuel Injector O-Rings w/Intake Removal.

My question is should I have all of this done? It's not cheap..roughly 1000 bucks. I know very little about this and I don't want to just tell my mechanic to do it without some research. Are these common problems with Monte's of this age/mileage and just part of the cost of owning this car. I am the original owner and have avoiding costly repairs/maintenance..it's been a great car.

View 4 Replies

Toyota - Corolla :: 2005 - Oil Change After Intake Manifold Replacement?

I have had a problem with my car idle hunting for about the past year. Last week my car threw a code and my code checker said that all 4 cylinders were misfiring. So I am still under warranty and took the car to the dealer. They said the intake manifold was leaking.

Two questions come to mind: Has to engine suffered any damage from leaking for over a year? and Do they automatically change the oil when changing out the intake manifold/gasket?

I did have an oil analysis last year (5/11) through Blackstone Labs and no antifreeze was present in the oil but the silicates were mildly high. Car is a 2005 toyota corolla with 102,xxx miles. The dealer also did the head gasket and a couple other engine gaskets 1 year ago.

View 15 Replies

Chevrolet - Silverado :: Check Engine Light Comes On After Intake Manifold Gaskets Replacement

I have a 1998 chevy silverado z/71 4x4. I had a water leak and had the intake manifold gaskets replaced. Ever since then, the check engine light comes on and it soots up the o2 sensors and the 4 plugs on the right bank. It may run good for a month or so and then it starts all over again.

View 1 Replies

Dodge - Avenger :: 2008 - Intake Manifold Runner Control Valve Stuck Open

Check engine light computer scan indicates intake manifold runner control valve stuck open. Will it damage the car to drive it in this condition and what does fixing it entail?

View 4 Replies

Prius (2004-09) :: Oil / Fuel In Intake Manifold - Misfire For All Cylinder And Reduce Engine Power Codes

I'm getting oil and fuel into the intake manifold every couple hundred miles. Oil level is in the middle of low and full mark. It's not like it's a huge amount of oil and fuel in the intake but it's enough to make the car misfire, bog out. Only codes I'm getting are misfire codes for all cylinder and reduce engine power code (forgot what code it actually is) but that's when the car completely shuts down and won't start with red triangle light. If I clean the intake out and unplug the battery for a few min I'm able to start the car again, but it will run really rough and white smoke will start to come out the exhaust (gas smell). I'm wondering if a bad maf would cause this. I've already cleaned it but still doing same thing. Don't really know what the specs or reading the bad is suppose to be so I'm kinda stuck to determined if I need a maf or not. Cars got about 242K miles.

View 17 Replies

Ford 6.0L Power Stroke Diesel :: 2004 F350 - Left Hand Exhaust Manifold Replacement

Attempting to take this on myself. My passenger side manifold was replaced a year ago.....BTW This damn truck - all stock - no modifications of any kind - just turned 100k miles. One owner - me.

So I have removed everything I think I need to to gain reasonable access including the fenderwell and all the intake tubes and battery and coolant reservoir. I want to use some heat and try not to break the bolts but there is a thin wiring harness just above the exhaust manifold. I can't find it in any diagrams on the ford parts site. It looks like the glow plug and injector harnesses are up above near the intake manifold but this one is down below all that. It connects to small rubber thing - 1 for each cylinder. There is nothing else electrical near it - everything else is up top.

Now my rant - look away if you are a die hard ford truck fan or 6.0L powerstroke fan.

So far I've had to replace both exhaust manifolds because they burned and rusted right through. New transmission cooler lines -yes - rusted through and cooler (because we couldn't get the lines off without destroying the cooler). Cat got clogged (that was fun to find and fix). All 4 front ball joints replaced. Transmission dip stick tube rusted through. Several brake lines had to be replaced due to rust. The air conditioner quit with about 80k miles. I haven't fixed that yet. My oil pan is rusting through and needs replacement. Friggin oil pan! I have never in my long life experienced that. I know of other diesel pickups that are older with far more miles that live in the northeast, used for plowing and never garaged that don't have their oil pans rusting through. Just had to change both power steering lines that go to the gearbox due to leak caused by rusting through. EGR needs to be cleaned or replaced almost as often as the oil need changing. This POS needs to be out of my life!

Too bad because if it was dependable and wasn't made out of the cheapest crappy metal Ford could find it would be a great truck. Rides and hauls great. Plows great. Good looking truck, too. Standard cab 8 foot bed. Dark green. Just can't keep doing this.

View 13 Replies

Ford Excursion :: 2001 V10 - Intake Manifold May Be Cracked

What are signs the intake manifold may be cracked? 2001 V10 Excursion....

View 4 Replies

Ford F-150 (2009-2014) :: Intake Manifold Swap?

Will an intake manifold from a new mustang 5.0 fit on a 2014 F150 5.0?

View 3 Replies

Ford Ranger / B-Series :: 2003 - Intake Manifold Leaking?

'03 Ranger, 2.3L. Runs great except at idle. Code p0171. Replaced IAC, no luck.

Brake cleaner leak test definitely results in engine rpm change right around "butterfly rod" plug in front of intake manifold near no. 1 cyl. I'm pretty sure that's the problem - the plastic plug blew out. I watched a video showing repair, but it seems lacking.

I do not want to loosen up intake for access - I'd rather remove steering pump and gain some access to plug it up. There still isn't much access but, but eyeballing it, enough to plug, I think.

Three steering pump bolts came out easy. The fourth one is behind fluid line - extremely difficult to access, imo.

Somehow try to remove pump for access to intake hole, or bite the bullet and remove intake manifold for access?

View 6 Replies

Ford F-150 - 1997-2003 :: 4.2L V6 - Intake Manifold Gasket Leak?

I've got a 1997 F150 with the 4.2L V6. Before I got it last summer I did some research, but apparently missed the issue with the intake manifold gasket leaks on these early engines. It seems to be a very slow leak, but obviously I want to get it fixed. I called Ford to see if it had had the recall work done on it, but all they could tell me is that there wasn't an open recall on my truck (with the exception of the recent fuel tank strap recall). Their system apparently only goes back 10 years, so they couldn't even see the freakin' recall. So, I've got a few questions:

1) I know I didn't post much info, but does this seem like an intake manifold leak?

2) Are there any special tools needed to change out the gasket myself?

3) Can you all recommend any replacement gaskets? I found a few different manufacturers of gaskets, but I'm sure some are better than others.

4) Can this issue cause the computer to throw the loose gas cap code (P0455 if I recall correctly).

5) Would it be worth it to just get a new truck? I really wanted a diesel in the first place, but I also hate to give up on a nice truck with only 115,000 miles.

View 6 Replies

Ford F-150 - 1997-2003 :: Ticking Noise In Intake Manifold

Replaced head gaskets on 2003 f-150 5.4. Now I can hear a ticking noise in middle of intake by #5 port. Maybe timing is off 1 link?

View 4 Replies

Ford Ranger / B-Series :: 1987 V6 - Intake Manifold Removal?

I was working on my friend's '87 Ranger with 2.9 L V6, and a little bit of dirt fell into the intake manifold through the injector ports and intake ports. I should've cleaned the top of the engine with a shop vac first. Anyway, should I remove the intake manifold, or try to vacuum the bits out? It's pretty oily inside, and they might be stuck to the inside of it, so the vac might not do much. If I have to remove it, do I have to de-mesh the distributor gear to remove it, or does the distributor attach to a splined shaft? After looking at the diagrams, the answer was unclear.

View 1 Replies

Ford - Explorer :: 1997 - Found Oil In Manifold And In Cold Air Intake System?

I have a 77 bronco with a 5.0 efi engine from a 97 Ford Explorer. I noticed there is oil in the cold air intake area and upper intake manifold. I was checking on things and noticed oil around the PCV valve and on the outside of the cold air intake system. Should I be concerned about this? I have done some research. I checked the PCV valve and intake manifold gasket which appear to look fine.

The PCV valve rattles and the gasket is intact. Granted there isn't a lot of oil when I looked inside the upper intake manifold but thought I should write and ask if this is a problem or not. Should I just replace them pcv valve any ways and recheck it after driving it for a few miles? The explorer did have 110K on it but when we took it apart we thought the engine looked great for how many miles it had on it. We did change out the cam and timing chain but as far as the other parts, we did not replace.

I am also getting a unusual reading to not reading with my oil gauge. When driving for a about 30 minutes or so, My oil gauge goes down to zero when I'm stopped but when I'm drive off then the pressure comes back up. When I have it in park the gauge reads fine.

View 6 Replies

Ford Ranger / B-Series :: Polishing And Porting Upper Intake Manifold

So i was thinking about buying a intake manifold for my truck and porting it and polish it. Would it be worth doing. I've decided that trying to port the heads will take up to much time and money for gaskets. Now the only reason why I am buying another stock one is so i can take my time and do it right.

View 14 Replies

Ford F-150 - 1997-2003 :: Dorman Intake Manifold Leaks When Cold?

so new motor new intake , rear passenger side decides to leak when roughly about 10 degrese or lower and being -13 yesterday and-18 this morning.

last year it did this n i put a nother hose clamp on that rear tube and just happened to stop . n now back but the ting is that its not wet at all at the hose but at top of head bottom intake hmm . this is all just during the initial start of truck stops even before truck really gets warm

if i tke it off n its messed up i hope its warrentied even though i painted it. if fine i guess add some gasket maker ?

View 4 Replies

Ford - Windstar :: 2002 - Intake Manifold Left Bank Stuck Open

I bought a 2002 Ford Windstar, it has over 154,000 miles on it. My problem is I got a ODB II code reader and it said that the Intake manifold on the left bank is stuck in the open position. How do I keep it from sticking.

View 15 Replies

Ford - Windstar :: 1998 - Code P1538 For Intake Manifold Runner Control

I have 98 windstar, p1538 code, IMRC. I have physically checked both IMRC's and they are functioning as they should. (if they were bad, they would not move at all right?) Assuming they are good, which step in the troubleshooting process I go to now? The van runs perfect, just that darn light! Do I start going for the O2 sensor now? What to next in the chain of troubleshooting?

View 14 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved