The truck seems to continue to crank sometimes even after I let the key go. Kinda like it's having a difficult time starting and NEEDS to be cranked a wee bit more and takes over for me. Is this an ignition issue that I can (need) to address or is it normal. I have ZERO experience with a newer vehicle nor a Ford truck.
View 2 RepliesMy young lad just picked up a 2004 F150 4x4. While fixing it up we have encountered a weird problem. The key goes in , starts and runs the truck but cannot be removed, unless you unhook the battery.
View 5 RepliesWhen I went to pull my key out of the ignition yesterday the key got a bit stuck and when I jiggled it a little to pull it out the chrome bezel that locks the tumbler in fell out. Now the tumbler is out as well and I cant figure out how to get the tumbler in and lock the bezel in place.
I see a pin on the bottom of the ignition cylinder that I should be able to push in and pull the cylinder out but I cant seem to push the pin in at all.
The key is stuck. It doesn't turn all the way back to the off position and the steering wheel will not lock. The shifter will still move when I turn the key and press the brakes. The car drives fine. Just can't take the key out of the ignition. This escape has the shifter on the steering column.
Solved: There is a tiny switch (like the one in the pic) that tells the car when the shifter is in the park position. It snaps into position in a little plastic slot. It had popped out of its slot and could not be actuated. It has 3 wires attached to it. I snapped it back into its slot and it works fine now.
Including a pic of it in its proper position. Hard to see it but that's how it looks when it is correct. Pic was taken with my phone stuck down behind it because I could not see it. So this view is as if you were inside the steering column looking back toward the driver seat.
It is located in the steering column near the top. The top cover on the steering column pops off and you can see it without taking the steering column loose, and with some skill and luck it can be snapped back into its slot. Also before inserting the switch, move the shifter down to another position so the little arm will not be in the way.
I accidentally put the key from my 2008 Honda Odyssey into the ignition of my 2004 Honda Odyssey, and now the key won't come out! How to get the key out? I tried jiggling the steering wheel, jiggling the key, disabling the battery, unlocking the gear shift and putting the car in and out of park, but nothing even remotely loosens the key.
View 2 RepliesI have a 2008 Prius. The black square key is stuck in the ignition and won't come out. I can hear clicking sound under the hood -- perhaps the battery. But the car won't start; the clock is off and the doors don't lock, except manually.
View 17 RepliesKeys get stuck in ignition lose all power have replaced ignition and shifter?
View 1 RepliesCar works perfectly otherwise. Good battery, a yellow top less than a year old. Made sure lights weren't on, took in and out of park, tried starting and restarting moving in and out of park. Turned steering wheel -- nothing seems to make a difference. What we can do to diagnose?
View 4 RepliesOK, here's the update so far.
- new battery
- all fuses fine in panel, all fuses fine on battery pack.
- am getting power to trigger switch upon engine crank (tested w lamp and volt meter).
- did the 'mechanics tap' on the starter motor body
Still no crank when key is turned, instrument panel/gauges light up as normal
So am I right in thinking that I've narrowed the problems down to:
1) bad solenoid
2) bad starter
3) bad connection between battery and starter
or have I missed something?
Also, is there a way to directly test the starter (or indirectly test the solenoid) by applying power to the starter?
Have a 2007 GX 470 with 70,000 Miles. Recently we have had problems with the ignition getting stuck. Key will go in, but, will not turn. Happens randomly and unpredictably. Will start after a period of time. Sometimes 30 minutes, sometimes several hours. My not happen for a few weeks or sometimes 2 or 3 times a week. Neither Lexus or Toyota claims to have heard of this problem.
View 14 RepliesMy key got stuck in the ignition and I was unable to start it. The owners' manual shows a small hole to the left of the key slot which is poked with a paper clip to release the key. At some point the ignition in my tdi was replaced and no small hole is present. A knowledgeable tow truck operator/mechanic coaxed the key from the ignition and the tdi started when the key was returned to the ignition and turned. What is the proper way to remove a stuck key from an ignition without the little hole. I was reluctant to force it out. The ignition currently in my '04 tdi has a raised bar to the left of the key slot which I was unable to depress.
View 3 Replies'04 RX330: Starting about a year ago, occasionally when inserting the ignition key it wouldn't turn to start. Take key out try again and it would start. Progressively, it seems to be requiring more and more in/out cycles to get the key to turn. It's like the transponder is not recognizing the key FOB. I have two keys, one is a master and other is a sub key, both have the problem. What has to be done to correct it? I'm afraid the dealer will just change some expensive ignition part when there's an easier fix.
View 14 RepliesMy 2004 Accent is stuck in the "lock" position in the ignition, and the wheel is locked and barely turns in either direction. I know this is supposed to be an anti-theft feature and I've tried all of the solutions listed here...
Turning the wheel hard and soft in either direction while holding the brake all the way down and trying to turn the key. Putting the car in neutral and then park and trying the above Disconnecting the battery for a few minutes and trying the above Jacking the car up on one side to release the tension on the pin.
My question is can I remove the spring at the bottom of the locking pin by drilling a hole in the center of the plate? I've seen a few youtube videos of this done on BMW's. It will cost me $500 minimum to replace the ignition or steering column based on quotes I got.
I have a Lexus RX 330 2006. Two days ago my key couldn't start the car he stuck inside the ignition. I ordered a locksmith guy and he open the auto meter so he can get to the ignition. Now the ignition working but when I try to start the car the car doesn't start. The security system turn on and off , it's seem like the car doesn't recognize the key, the guy also make a new key and program the car but still the car is not charging, I also order mechanics to see if somethings wrong with the car and he didn't see any problem . I think the car shut down and I need professional guy who know how to program the car...
View 4 RepliesHave an 04 ford f-150. igntion getting hard to turn of. not all of the time but still has its moments. thinking of using some graphite to lube it up.
View 2 Replies2008 F150 XLT 5.4L
1. Replaced fuse #9 for fuel pump.
2. Checked fuse #9 with check light, power to both sides is good
3. No check engine light
4. Battery is 1.5 years old. Just in case I charged for 1 hr.
5. Replaced fuel filter. Possible clog in fuel line.
6. Detached fuel line at fuel filter, turned key on and fuel came out of line. Seems like fuel pump is working.
7. Every time I can hear the fuel pump prim when I turn the key.
8. Relay#1 starter solenoid, I swapped with relay #2 and also replaced
9. FPDM replacement, I removed and it looked to be good.
10. Light checked all fuses, only fuse #5, fuse#35, and Fuse#36 did not have power. These fuses don't seem to have anything to do with starting or fuel to the engine.
11. Inertia switch check is good
My main problem right now is that i am stuck in 4x4 low. Organically (should have left it at this) my truck would not do anything, no 4x4 high or low lights when i turned the switch.(lights worked when truck is first turned on) I researched it on the net and came across the idea to tap the Transfer Case Motor. I did this and my truck locked in 4x4 low and would not come out. I kept tapping on it while someone turned the dash switch and nothing, so i ordered a new(rebuilt) motor (160.00!!)
I got the new motor today and while installing it (I replaced the 2 speed wires) i turned the switch and it went in 4x4 high but i put it back in 4x4 low in order to bolt the motor to the transfer case. After I bolted it on, I tried to take it out of 4 low (in neutral and foot on brake) and it would not disengage. My front hubs will not lock, i am going to get on this after i get it out of 4x4 low(take it to a friends shop so i can lift front end up etc.) I have recently replaced the iwe solenoid on the passenger side firewall.
How do I remove ignition lock cylinder to take and get new set up?
View 4 RepliesLooking at buying this used 2004 F150 and the Seller says it has a problem with the ignition switch; that it continues to run the starter even after the engine is running, which burns out the starter. He's an obvious layperson and doesn't know much about mechanical stuff (or he's pretending, IDK).
This sounds very strange to me, because if it's some kind of mechanical defect/factory defect, it's something that Ford should have identified, documented, issued a recall maybe, or something, yet when I research the issue the only thing I find is a problem with ignition switches that cause fires in model years that end in 2003 (not 2004). Other than that I find no documentation.
I wonder how accurate the Seller's description is, or maybe it's defective due to some other reason, like maybe a car thief shoved something into the ignition and damaged it, or possibly corrosion. Or maybe it's simply "sticky" and some spray lubricant would fix it.
I have a 2004 Lariat 4x4 with a no start condition. I had lights, but it wouldn't crank. I then discovered that it would not shift out of park. Turns out that it had a blown fuse. I did not have any of that type (the funky square 20a fuses) so I pulled the heated seats fuse (30a) and threw it in there, tried to start it and blew it right away. Is there a common short to look for on these? I believe that the guy that owned it before me had a satellite radio in it, and could it be a bare wire from that setup possibly blowing the fuse?Just trying to get a head start on tracking down the short.
View 14 RepliesWent to leave this morning and my '05 with 135K would crank but not start. Pulled air cleaner and sprayed a little starting fluid and it fired some so I had a feeling it was fuel related. Reset the fuel cut-out with no luck. I then remember seeing the issues on the forum about the fuel pump driver module corrosion and failures. Bought a new one at the local dealer, installed it and it fired right up.
Pics below...from the side it didn't look to bad but was holed through on the bottom. I highly recommend replacing this if you live in the rust belt.