Ford F-150 (2004-2008) :: Idle Not Staying Smooth


Apr 6, 2014

My truck has been running great for the lasts 2 years. Today is actually the 2 year anniversary of me buying the truck. Still have great power and rumbles great down the road with no lights or anything.

Lately though at stop lights my idle will be inconstant. Will either sit smooth at about 550rpm, or be high but smooth around 700, OR that one that worries me the most is it will idle at 550rpm then drop down to 450 or so then catch itself and go back to 550, then drop back down.

It has the usual maintenance, new spark plugs around 100k, oil change and air filter just a few weeks ago, so this idle has me a bit puzzled. Maybe time for a new fuel filter? MAF sensor dirty?

View 4 Replies

Advertisement

Ford F-150 (2004-2008) :: Battery Drain - Stereo Staying On Once Truck Has Been Turned Off

I HAVE A 2005 f-150 LARIET 5.4 lt. I have been having a problem with my battery being drained. My stereo has been staying on once the truck has been turned off. It has also been coming on when the truck is parked all by itself and draining the battery. Sometimes when i am driving in the truck and turn the stereo on it wont come on, ten minutes down the road the stereo will all of a sudden come on. I have tried removing the relay for the stereo, no difference. I have also removed all fuses for the stereo and entertainment system, yet the draining of the battery is still occurring. What the problem could be?

View 6 Replies

Ford F-150 (2004-2008) :: Truck Lost All Power / Barely Staying Running - Code P0012

2008 F150 5.4L .. The truck lost all power the other day driving and barely made it to work. On the ride home it was still running horribly, like it just fell on its face. the check engine light came on. Went to autozone and put HEAT in the gas tank cuz the night before it was at quarter tank and temp went from warm to freezing(thought maybe condensation in tank).. Truck ran a lot better( not perfect). Drove around that day and it was fine. Pulled down the driveway and CE light shut off. Ran the code anyways and it was P0012..

Talked to a few mechanics and they said try replacing the Camshaft position sensors..did so and it ran worse. the truck hardly would idle or rev and shook violently..i shut it down right away. Then it threw 9 codes..Cam shaft position- over retarded timing bank 1(P0012), misfire cyl2, misfire cyl3, misfire cyl 4, random misfire, cam sensor bank 1, three of them were repeated codes..

I replaced the sensors back to stock and cleared the codes. the truck is running like it was in the beginning of the problem..No vilant shaking but falling right on its face at idle and any rpm..not drivable. Would rather do the work myself. very capable except for replacing camshaft phasers which i have heard could be the issue..Could it by the VCT seliniod, EGR valve, plugs, wires...Did just change the oil a week ago and cleaned and reoiled air filter.

View 11 Replies

Ford :: 2006 - Rough Idle And Can't Seem To Get It To Smooth Out

I have a 2006 Ford 150 with about 120,000 miles on it... For almost 9 months now I've had a really rough idle and I can't seem to get it to smooth out. I've tried new plugs, tune up, new fuel filter, higher octane gas, fuel injector cleaner, octane booster, cleaned my mass air flow sensor and nothing works... I've checked the trucks ECM for any codes but it comes up clean every time...

View 6 Replies

Ford 6.0L Power Stroke Diesel :: 2003 F350 Engine Not Running Smooth / Skipping At Idle

2003 F350 6.0 with 290k+ ... It has a skip in the engine at idle and running. At times when running down the road skip seems to get worse. Changed both fuel filters, didn't work. Truck start up is normal, no leaks, and flashing no codes.

View 3 Replies

LeSabre :: 99 - Cold Start Rough Idle But Smooth Out

I have a 99 lesabre cold start rough idle but smooths out . Warm no start. Trouble codes P0171, P0300, P0336. Had plennum replaced 2 years ago but I'm seeing coolant around the base of the plennum so I'm going to have to do that again but I don't think that has anything to do with the warm no start.

View 14 Replies

Camry :: 2006 SE Engine Smooth But Dash Rattle At Idle

I recently purchased a 2006 SE with 4 cylinder/at combo. Engine is silky smooth, but I have a rattle that I think is coming from behind the driver instruments or against the fire wall where the brake m/c is. This only occurs when the engine is in gear, mainly with a/c on, & the idle drops to 600-700 rpm range. Like if I am sitting at a red light for more than a minute or two. If I put the tranny in neutral, cut the a/c off, or step on gas to raise the idle speed the rattle goes away. It's definitely rpm dependent.

It's not the a/c, because I have been able to repeat the issue with the a/c off. I did notice that on the back of the air filter box, there are several plastic components attached but what they do. Is there anyway to increase idle speed?

View 2 Replies

Passat (B5) :: Lumpy Idle / Smooth Acceleration And Misfires - CPS Error

I am trying to track down a problem for a friend with a 2001 Passat, 1.8L. The car has 150k and had a timing belt about 50k ago. About 3 weeks ago, it started misfiring badly on idle. In gear driving around, it purrs like a kitten. I scanned for codes and got:

Address 01: Engine
Controller: 4B0 906 018 CL
Component: 1.8L R4/5VT G 0001
Coding: 16551
9 Faults Found:

[Code] ....

At first I thought it might be a vacuum leak, but it looks like when he took it in 2 weeks ago they replaced all the vacuum hoses. It is unclear when he last had sparks and coils. I understand the likely culprits are:

sparks
coils
ICM

I am hesitant to blame sparks/coils if he is getting misfires on all 4 cyl. It seems like they might have screwed up the timing belt install given the camshaft sensor error, but he's been running for 50k miles since the change, and this idle issue just appeared recently.

View 2 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 - Smooth Idle But No Power

I purchased a 2000 excursion with the 7.3 a couple of weeks ago. The guy said originally in the add that it need #2 and #8 injectors replaced. When I went and looked at it he had already replaced them and said the it still has no power and needed the remaining 6 replaced. I purchased it as it was a good deal thinking I should be able to get it fixed for worst case a set of injectors. BTW the engine has little to no blowby and starts easy and idles great.

The problem it it will not build any boost (has external boost gauge). Actually the gauge only shows vacuum. With the truck in park or neutral you can slowly rev the motor to 2500rpm and all seems fine but as soon as you break past 2500rpm it sound like it is missing and starts blowing white smoke. The smoke smells like when a diesel heater runs out of diesel. If you try and drive it it has NO power and will not move out of its own way and will eventually start like it is missing and blowing white smoke.

The previous owner replaced the following:

#2 injector
#8 injector
UVC gaskets
MAP Sensor
Wastegate solenoid sensor

The first thing I did was start looking at the no boost issue and pulled the turbo. I deleted the EBPV while i was there. Also the turbine wheel was in very bad shape so i replaced the turbine wheel, shaft, seals, bushings and installed a new compressor wheel 5+5 wheel off ebay. Reinstalled turbo and the symptoms are the same. I also replaced the clamps on the spider with Tbolt clamps instead of the worm gear styles and it psi tested all piping and intercooler to 30psi with no leaks. Also the up pipes have already been replaced with the bellowed style so there are no leaks and it has a 4" straight exhaust.

I have since ordered oring kits for the injectors and also ordered the fittings for the fuel bowl so i can check fuel pressure. it has a new air filter, oil filter, oil and fuel filter installed.

The ICP sensor has oil in the plug but if i unplug it the symptoms are still there.

I have also used a scanner and the ICP pressure is approx 500psi at idle and the duty cycle is about 11% at idle. Also the HPOP looks to be new as it is very clean compared to the surrounding parts and i have checked the HPOP reservoir and it is full to withing 1/2" from the threads.

2000 Excursion
7.3
205000 miles

I am assuming that the injectors are original other than #2 and #8.

View 14 Replies

Buick - Lesabre :: 1994 V6 Smooth When Idling In Park But Rough Idle In Gear?

1994 Buick LeSabre Custom 3.8 Litre V6 with 103277 miles.

It runs smooth when idling in Park, rough when I put it in gear when I am stopped (either drive or reverse) has hesitation when accelerating, it smooths out again when driving then it starts to drive rough at about 55 MPH.

Mechanic told me it was the plug wires. I replaced those and the plugs. This fixed the hesitation when accelerating issue, but the other issues remain (now even seem a little worse) I thought the plugs and/or wires were bad, so I rechecked the gauge on the plugs and traced to make sure I had the wires hooked up right. Everything seems in order.

I have added fuel injector cleaner, and changed the oil, oil filter, spark plugs, spark plug wires, air filter, flushed the radiator, and changed the thermostat. (For a tune up since it has admittedly been a while)....

View 1 Replies

Honda - Cr-v :: 2008 - Bumping At 60 Mph And On A Smooth Road

At 60 mph + and on a smooth road, this 2008 CR-V presents with what seems to be an out of balance issue. You can feel it bumping when it reaches this speed and beyond. The car just turned 100k, had four new tires about a year and a half ago, but when this began occurring (and it was pulling to one side), the dealership recommended two new front tires due to something they couldn't pinpoint as to why the tires were wearing as they were. Replacing them fixed the pulling to one side problem but did not correct the bumping problem. The car has never been in an accident or been driven over a curb/bank, etc., is driven by the same person, has always been maintained at the same Honda dealership. It has been to them 3 times is about to go back for the fourth time. Could it be a bearing? An axel problem? Bad replacement tires?

View 1 Replies

Ford - Lincoln :: 2004 - Rough Idol But Runs Smooth When Gas Is Given?

My 2004 Lincoln navigator is very rough at idle but runs smooth when I give it gas. Someone said my VCT may be stuck or bad. I looked at Youtube videos of VCT replacement but in all the videos the VCT's are up front in the valve covers. On the Navigator they aren't there. Where the heck they might be located?

View 2 Replies

Ford F-150 (2004-2008) :: 2005 - Rumble At Idle?

my 05 f150 5.4 with 76,000 has a weird rumble at idle, I don't think its a miss and there's no codes and when I put it in park it goes away or if the idle changes just a little you don't feel it. And you feel it through the brake pedal the most its not real bad butb enough to bother me.

View 5 Replies

Ford F-150 (2004-2008) :: Knocking Noise At Idle

In this video I go over in detail the procedure to swap out the Cam Phaser to get rid of that annoying knocking noise at idle! It is easier than you think. The procedure is the same for all 4.6l and 5.4l 3valve engines.

Ford 4.6l 3v & 5.4L 3v Camshaft Phaser Knocking Noise Fix - YouTube...

View 6 Replies

Ford F-150 (2004-2008) :: 2006 - Rough Idle

I have a 2006 f150 I just bought after my F250 was stolen. It has about 70k miles. It has been running pretty rough ever since I got it. It finally threw codes so I tried to address all the issues. Changed out a couple coils and all the plugs (motorcraft platinum). The camshaft sensor was also bad. Truck runs much better but still has an idle issue I cant seem to nail down.

I assume its something to do with air intake. It doesnt happen all the time. It runs rough and knocks and sometimes dies. If I give it gas it stops. I read it could be the idle air intake valve, but then I read that this model doesnt have one. I also read that air intake issues dont normally throw codes. Are there any common problems I could look for? Would cleaning the throttle body do any good?

I know the basics, but this kind of thing is tough for me to troubleshoot. You may have already seen me post this problem, but I didnt get much response so I thought I'd try one last time.

View 11 Replies

Ford F-150 (2004-2008) :: Stalling At Idle And When Trying To Park

My 2004 fx f150 with 177K miles is stalling (rpms bottom out) driving down the road and coming to a stop (coming to idle) and when trying to park. AND, its an intermittent problem.

Of course, not spitting any codes or CEL's. I've searched the site and there are multiple types of the same issues and solutions. Narrowed it down to either the dreaded vacuum line sandwiched against firewall and engine compartment, OR the cleaning of MAF, throttle body and IAC valve.

View 12 Replies

Ford F-150 (2004-2008) :: Rough Idle Intermittently?

Ok, so I just replaced the entire timing set (phasers, chains, sprocket, tensioners ect) on my 2004 f150 5.4l about a month ago. I also extracted ALL 8 spark plugs and replaced those with the Champion 1 piece plugs. In addition, I replaced the intake manifold because I did this job when it was 20 degrees outside and I found a crack. Soooo, all that being said I put the whole truck back together and it runs like New. Until about a month later. When the engine gets hot, maybe after about a 30 minute drive or so, it has a really really rough idle until I give it a little bit of gas. Then it clears up. It has only done it 3 times since I put the engine back together. It might go 2 weeks and not do it. No codes. What I could be? EGR? MAS air? Only other thing I can think to say is if you get on it out on the highway, after about 3k rpms it seems like the power drops off quite a bit. Like the engine isn't getting enough fuel. I guess it could be just me, but it just doesnt seem right.. I guess I could try to unplug the MAS air flow sensor...

View 14 Replies

Ford F-150 (2004-2008) :: A/C Won't Work At Idle Speed?

I have a 2008 F-150 4.6 the AC blows cold driving down the road, but when I stop and idle it gets warm, doesn't blow cold took it to a shop they told me it was the electric clutch fan 550 bucks to replace was bad the truck doesn't overheat and the fan is working and kicking up a speed at idle just want a second opinion before i spend that much. I can get as to what might be causing the problem

View 8 Replies

Ford F-150 (2004-2008) :: V8 - Engine Knocks At Idle?

As stated I have a 2008 F150XLT 5.4 V8. Recently it has started making a knocking noise and very rough idle when warm. It only does it when the truck has been driven slowly or typically when going through a drive through. It sounds like a rod knock but putting it in neutral and revving the engine makes it go away for a while.

View 8 Replies

Ford F-150 (2004-2008) :: Rough Idle Almost Like A Misfire

I hopped in my truck this morning, fired it up, and it idled nicely. I drove around the corner, and noticed that the truck was barely responding to the throttle. Then things got shaky. It was a very rough idle, almost like a misfire. But I managed to get the gas to respond and got the revs up to about 3K and it seemed to run smooth.

No CEL either. Currently, I have no place to really look at my truck as I don't have a garage, or driveway for that matter. I don't have a scanner that can read live data either. I'm limited in my tools currently as well.

View 3 Replies

Ford F-150 (2004-2008) :: Low Idle When Put In Gear And Sometimes Stalls

I changed the plugs on my 2004 F-150 FX4 with 165,000 miles. Immediately afterwards I experienced a low idle problem. After engine warms up, idle is at about 400 rpm in nuetral or park. When I put in gear it drops to 200 rpm and sometimes stalls. Ford analyzer says misfire #8 cylinder. I swapped coils with #7 and reset fault. #8 cylinder misfire came back. So next I put new plug in #8 thinking the plug was bad. Still have low idle problem. What I should try next?

View 3 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved