Ford F-150 (2004-2008) :: Hesitation At 40 - 60 Mph During Heavy Acceleration
Jun 7, 2017
Here's the story on my truck. Spits and sputters between 40-60 during heavy acceleration and on rare occasions will jerk/pop while at a steady speed. No engine or wrench lights. I thought it might be the fuel filter and changed that, it didn't work. I also ran two bottles (on 2 separate occasions) of Duralube extreme fuel system cleaner, that didn't work either. So, I took it to the Ford dealer for a diagnostic. They had a hard time getting it to act up but said it finally misfired on #8 and recommended replacing the ignition coil and plug. I did that, still have the same symptoms. So, I thought it might be the fuel injector and changed that. Still same symptoms and ZERO dummy lights.
After several YouTube videos, I thought it might be the TPS and got one. Before I changed that however, I cleaned the Mass Air Flow sensor, still same symptoms. I finally changed the TPS, but the engine wouldn't start or run at all, no warning lights yet. When I put the old TPS on, it would run. I unplugged the TPS and it still ran but very rough. Now the engine light IS on! Thinking I purchased a bad part, I took it back to O'Reilly's and they warrantied it out and gave me a new one. I had 19 PO codes. I changed the TPS again, and, it won't start or run at all. Put the old one on and it runs. They cleared the codes and told me they think it could be the ECM/PCM.
Why will a new TPS not work? I still have the same issue of hesitation @ 40-60 during hard acceleration. No hesitation during a moderate acceleration.
View 1 Replies
Advertisement
What a year 2014 has been. I had a 2005 F250 6.0 that was stolen in March and totaled when found days later. My insurance gave me enough to pay off the loan and render me the obstacle of replacing it. I got my F250 pretty cheap so replacing it for the insurance pay out was non-existence. I ended buying a 2007 F150 EC 4X4 w/ the 5.4 and having 97,000 miles on it. Just as luck would have it, I had the F150 for about a week before the cam phasers went out. Luckily the warranty covered it enough to put in a new LKQ reman engine.
I got the truck back about 2 weeks ago and put 1,000 miles on it in a very gracious form. I have noticed since then that despite letting it warm up for 20 minutes, I could put the throttle on the floor and the outcome was very poor. It was almost as if I was attempting to pull a house down. I couldn't even get the tires to spin at all, not even on wet pavement. Now I know this is not my old F250 6.0 turbo diesel, but really, I expected more from a new reman engine! They used all components from the old engine except for new spark plugs and a fluid change. Why is this "new" reman engine so weak?
View 4 Replies
I posted a while back about my 04 5.4 having an issue at idle. I did all the normal things like replace coil, spark plug, etc etc. No change to the issue. It still acts as though it's misfiring on a cylinder and I get codes P0306 and P0316. Finally took it to ford and had a diagnostic check ran. Everything on the top end was in working order. The tech even put a known working coil on 6 and nothing changed. I was told that it's either an intake or valve issue on that cylinder. But no definite answer to problem.
Fast forward to yesterday. I got a wild hair at lunch and went out and started truck. Pulled injector plug off of 6. No change to the way it was running. I did the same for 5, 7, 8, 1, and 2. All of which made a big difference in the way it ran. It was obviously misfiring with no fuel to cylinder. This gave me the idea to swap 5 and 6 when I got home to see if the issue followed the injector from 6. I did NOT. I pulled the plug on 5 and got the obvious change in the way it ran. So there is definitely something going on at cylinder 6 that I cannot figure out.
PCM, bad intake, bad valve? I'm not rich so a trip to ford for repair is gonna have to wait. Truck seems to run fine when driving except for slight hesitation during acceleration.
View 3 Replies
I bought a used 2008 Sonata GLS with 65K miles 2 years ago. It's been a great car so far. For the first 25K miles that I drove it, it had good pickup and got ~30 MPG for my highway driving. In the last ~5K miles, the fuel mileage has dropped to 25MPG highway and it has some hesitation when accelerating, especially on lower RPM's. I changed the spark plugs with NGK Iridium, but it is still having the issue. What to check?
Some possibilities: ignition coils, sensors, timing belt, etc?
View 5 Replies
Toyota says the code is P0420 and the Catalytic Converter is rattling under heavy acceleration showing the Catalytic converter is bad and should be replaced. Toyota wants 2,334.00 which seems very high to me. Is it the Catalytic converter? The car is a 2004 Toyota Prius.
View 12 Replies
I purchased a 2006 Ford F-150 XLT, 5.4 3V Triton. Last Thursday my check engine light came on, so I came to this forum and found out how to retrieve the code with out a OBD. It came up as a 0301 Misfire cylinder 1-10?
I went to the dealer and they said it was cylinder one, sold me a new plug and coil pack and they installed it for a nice $$$. On my way home it started to sputter again when you give it heavy throttle, I called they told me that I should change all the plugs and Coil packs, kinda makes sense but to have all 8 plugs and coils go at once it only has 83km on it.
View 14 Replies
I recently bought a 2004 XC90 T6. It has several issue and one strange issue is the sluggish performance: the vehicle sort of hesitates, requires quite a bit of acceleration effort to get up to speed, feels 'heavy', and in general does not seem to have the right amount of power. What makes the issue strange is that performance improves, noticeably, when the car is starting to run out of fuel, or when the "low fuel" light comes on. It is not a placebo effect: i've verified it several times that soon after the light is on, the vehicle becomes a lot more responsive, accelerates well, engine seems to sound quieter a little even.
I do not know much about cars. I am slowly learning after purchasing this vehicle. I verified that the air filter is clean. It has synthetic oil put in. I recently changed the spark plugs (very proud of that), that did not seem to improve the performance. My plan is to purchase and configure VIDA diagnostic tool and scan the vehicle while driving. It might also be worth mentioning that the vehicle is getting very poor mpg, averaging to 6 km per little.
One important note: the MAF sensor is faulty: i drive with it being unplugged, however when it is plugged in i experience the same as described above. I know it is faulty because when it is plugged in and the car is started up, the RPM goes to 2000+ and there for up to a minute or longer. If the MAF is unplugged this does not happen.
View 1 Replies
I've got an '06 F150 and the steering isn't right with it. It has had a heavy feel and is almost like the power assist is only working half as good as it should. It's been like this for a couple months. I 've had all four ball joints and the steering rack replaced in the last month. It had the heavy steering feel before and after everything was replaced. It also doesn't recover itself on sharp turns, I have to turn the wheel back as I complete the turn. Could it be the power steering pump? I thought it was a mechanical device and it either worked or it didn't, maybe they get weak?
View 14 Replies
I have an F-150 Heritage 4.2L V6 Manual 4X4 and over the last few weeks have notice a couple of odd things. First I noted an odd screeching sound, similar to a rock caught in the break drum, but it seemed to be coming from under the cab/bed, not a tire. It only seemed to show up under relatively heavy throttle, which I thought was odd. I went through a car wash with a good under carriage spray, and the sound went away.
A few days later it snowed and the sound returned. I don't know that it's actually related...but that's how the weather went... Now, when I let off the throttle and the engine holds the truck back there is a "thump", and when I reapply the throttle, it thumps again. If I press the clutch in first, then release the throttle there is no thump; so I assume this is something with the drive shaft.
I climbed underneath and found that I do have some play in the shaft, I can twist it a tiny bit so I know that I have play in the shaft which (and I am NO mechanic) I assume is not normal. I can see the shaft turning all the way to where it goes into the back of the transmission so I assume the play is coming from the rear yoke?
I thought I could replace the yoke relatively cheaply but I keep stumbling across posts indicating that with this particular set up, I actually have to replace the whole drive shaft. What I could be looking at, and what my options are?
View 3 Replies
Have a trusty 05 stx 4.6 4x4 automatic 44,000 orig. miles/owner ext cab pick up. Just lately I thought I picked up at tree branch or something make a noise very similar to pulling a hung up branch or something.. Stopped, looked under truck (everywhere) no dice! Then did some research.. Noise went away when not giving it gas or gliding in nuetral just when light or heavy accelerating! Where do I begin??
View 7 Replies
My truck is just turning over 100k miles and I still love her like she was new. Recently I've noticed accelerator hesitation (especially in slow traffic) that wasn't there before. Also something new, the fuel system no longer bleeds pressure when I remove the cap to gas up. I think the lack of fuel system pressure has something to do with the hesitation. I did the easy thing and replaced the gas cap. I asked the dealer and they checked fuel pump(s) output pressure and said they were normal.
View 11 Replies
I have Hesitation problem with my expedition 2004 during mooring time some time when car in cooling condition but now days must of the time I have this problem I want to many work shop and the tested my car by computer but they cant find clear fault the told they need to check many thing.
View 2 Replies
Quick truck stats: 2005 F150, 5.4L, 85,000 miles
The past few weeks my engine has been hesitating on some cranks before it would start. I figured it was due to the cold weather so didn't pay too much attention to it as it was also not throwing the check engine light.
Yesterday it didn't start at all after the several attempts of just cranking over and over. It still didn't seem to trip the check engine light but I pulled my scanner out anyways and it had the code p1237. I cleared it and the truck started right up. It even had no more issues the three times I started the truck after that.
Today, however, she is not starting again and not throwing any codes. Still cranking so I'm sure it's not the started or the battery. I'm going to have my husband pick up some starter fluid on his way home today to see if I can at least get a temporary start since I think it's the fuel pump, or possibly the fuel filter. It is cold again this morning so I'm wondering if the cold is somehow making this issue worse. Either way I'd like to fix it, since being stranded with a truck that doesn't start is not my idea of a way to pass the time.
What else it might be and how I might be able to diagnose it?
View 4 Replies
This morning as I was driving to work, my truck hesitated as I tried to accelerate from a stop sign. I pressed the pedal and nothing, almost felt like it was going to stall. After about 3 seconds it started driving again and I had no further issues. It seems to only do this in the morning when it is cold. It has done this a couple of times before, but usually it recovers almost immediately. I had no CEL come on. 2007 F150.....
View 1 Replies
How's it going? I have a 2005 F150 with the 5.4L V8. It has 70,000 miles on it and until yesterday and has been a great truck. While driving in traffic yesterday the truck started running rough and hesitating. It through two codes - misfire cylinder 5 and misfire cylinder 6.
In response, I purchased two new coils and 8 new autolite plugs. The plug installation went smoothly and the coils all went on without incident. However, this didn't fix the problem!
The next day I found that cylinders 5, 6, 7, and 8 were all having issues. At this point I also had an "O2 stuck lean" code so I pulled the plugs and found all four brand new plugs fouled and smelling like gas and an ehaust that smelled like raw fuel. This led me to replace the O2 sensor on the drivers side. With the new O2 my lean code disappeared but I still had a rough idle.
Further troubleshooting found that injector 6 was stuck open (which presumably fouled my O2 causing it to read lean and dump fuel thus fouling all the plugs on one side). I replaced the injector and the rough idle disappeared and all seemed really well as the truck idled in my driveway.
However, as soon as I hit the road I noticed a major hesitation. The motor is also noticeably louder and has a very hard time accelerating. I'm thinking that I've plugged up my cat by dumping so much fuel in to it and the hesitation is caused by a lack of breathing - does this sound possible? How would I confirm this without replacing the cat? Anything else I should look for? I'm fairly confident I have combustion in all 8 cylinders now so I'm leaning towards intake/exhaust issues.
View 13 Replies
I have a 2008 Ford F150 4.6L and its been broken down in our shop for quite some time now. It started acting funny when I could not get the truck to do over 80kmh. Slow acceleration, and a horrible shaking when it idled. Eventually it was undriveable since I could go above 50kmh anymore. From looking online we replaced the plugs and coils. We removed the intake to find the gaskets were shot so coolant was leaking into the spark plug tubes which could've been the cause of a misfire. Fixed that. Still the same. We replaced the egr valve and dpfe sensor because we keep getting the P0402 excessive egr flow code. Still no luck. My dad is a journeyman hes just not too familiar with newer trucks.
View 4 Replies
First, a little background on my truck. 2007 with 5.4, 122000 miles, oil changes with 5-20 Motorcraft and Motorcraft filters, plugs done by dealer 40000 miles ago. The truck has developed a ticking noise, kind of like a lifter (I know these engines don't have lifters) that is most noticeable from the side of the truck near wheel. ticking speeds up with the rpm. Also around same time, between 40-55 under load there is a bit of a stumble, but I can gas thru it. I'm guessing these are related. I'm thinking spark plugs again, but shouldn't I get more than 40000 out of them? I might just take it in, since I've got oil leak somewhere around back of the oil pan, but figured maybe might get some clues first. Also, no CEL.
View 4 Replies
I have a 2008 Passat Komfort Wagon with the 2.0T. At 40,000 miles, yes it only has 40,000 miles, the thing started hesitating and misfiring on me only during heavy load. I ran the codes and it said #4 cylinder misfire. The check engine light was only on during the time it was misfiring and hesitating. Took it to the VW dealer to have them run it again and get guidance and they verified the #4. When I picked up the car the CEL was illuminated. They said it does it when it misfires. I explained that it was not on when I dropped it off and they basically said tough cookies. So I replaced the #4 coil pack and all 4 plugs. CEL light still on, but wasn't misfiring. Next day it began misfiring again under heavy load. Took to Autozone to run the codes and now says misfiring on all cylinders.
View 6 Replies
I have a 2005 F150 with the 5.4L V8. It has 70,000 miles on it and until yesterday and has been a great truck. While driving in traffic yesterday the truck started running rough and hesitating. It through two codes - misfire cylinder 5 and misfire cylinder 6.
In response, I purchased two new coils and 8 new autolite plugs. The plug installation went smoothly and the coils all went on without incident. However, this didn't fix the problem!
The next day I found that cylinders 5, 6, 7, and 8 were all having issues. At this point I also had an "O2 stuck lean" code so I pulled the plugs and found all four brand new plugs fouled and smelling like gas and an exhaust that smelled like raw fuel. This led me to replace the O2 sensor on the drivers side. With the new O2 my lean code disappeared but I still had a rough idle.
Further troubleshooting found that injector 6 was stuck open (which presumably fouled my O2 causing it to read lean and dump fuel thus fouling all the plugs on one side). I replaced the injector and the rough idle disappeared and all seemed really well as the truck idled in my driveway.
However, as soon as I hit the road I noticed a major hesitation. The motor is also noticeably louder and has a very hard time accelerating. I'm thinking that I've plugged up my cat by dumping so much fuel in to it and the hesitation is caused by a lack of breathing - does this sound possible? How would I confirm this without replacing the cat? Anything else I should look for? I'm fairly confident I have combustion in all 8 cylinders now so I'm leaning towards intake/exhaust issues.
View 5 Replies
I have a 2004 F150 4x4 super crew with te 5.4L in it. Truck has 200K plus miles on it and I went to start it after driving (it may have say for 10 min) the truck hesitated and didn't start and smoke started coming from under the hood. Looked like it was coming from the drivers side maybe mid fender or closer to the firewall. Look at it and nothing was on fire but something defiantly happened cause now its compensating for something. The rpms are up from what they usually are and the drivers information was cleared. Truck runs now but just worried
View 6 Replies
I've got a 2000 accent 1.5, and I keep getting a code for a cylinder 3 misfire, when I change the spark plugs, it runs great for about 50 miles or so, then back to square one again. I just changed the coil pack the other day and there doesn't seem to be much of a difference. It has massive hesitation under heavy throttle, and the check engine light begins to blink if it sits and idles for too long. I've scanned it multiple times and it's always been cylinder 3, so it's definitely set on that one... I'm about stumped on what this could be. Also, the previous owner said that after a hot day of driving, the ECU fuse under the hood will blow out, what could cause either one of these things?
View 40 Replies
