Ford F-150 (2004-2008) :: Got Codes P0174 / P0171 / P0345 And P0349?
Mar 19, 2017
My truck have 4 codes p0174 and p0171 system too lean bank 1 and bank 2, and p0345, p0349 camshaft position sensor bank 1 and bank 2.
View 3 Replies
Mar 19, 2017
Advertisement
Ford F-150 (2004-2008) :: Misfiring - Rough Idle - Got Codes P0340 / P0344 / P0345 And P0349?
I recently purchased a Ford pickup. I bought a 2004 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 200,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run good when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come to on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
Ford F-150 (2004-2008) :: 2006 - Missing And Rough Idle - Codes P0340 / P0344 / P0345 And P0349?
I recently purchased my first Ford pickup. I bought a 2006 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 146,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run well when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around the rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
Ford F-150 (2004-2008) :: 4x4 Doesn't Engage - Codes P0171 And P0174 When Switch To 4LO
Just recently replaced the driver side 4wd actuator. When testing the system to see if it was working, I noticed that in 2wd everything seemed to be in order (wheel spun without the half shaft, no grinding noises on test drive, seemed good to go).
However, when I switched to 4hi, the dash light "4HI" would come on but the wheel still spun freely without the half shaft. When the truck was off, the wheel and half shaft spun together as they should when vacuum is released from the actuator. When I switched to 4lo, the dash light did not come on and the check engine light came on. Pulling codes revealed P0171 and P0174.
Could these codes be caused by a bad solenoid? Is the solenoid not switching the vacuum off and that's my issue? Are there other possibilities?
Ford F-150 (2009-2014) :: Codes P0345 And P0349 - Camshaft Position Sensor Bank 2 Circulation Error / Interim
For 2009 and 2010 f150's with the 5.4L engine, this may apply to you.
About a month back I got some odd vibrations at start-up and while driving and the following codes:
P0345 - Camshaft Position Sensor, Bank 2 (drivers side), circulation error
P0349 - Camshaft position Sensor, Bank 2 (drivers side), circulation Interim.
These codes are common in the previous generation truck for various reasons. In my case, I started trying to troubleshoot with the easiest solutions first.
Checked the battery - fully charged.
Checked/played with the alternator connection and related wiring - looked good.
Checked the oil - it was down at the half mark on the dipstick, so toped it off with synthetic oil.
Cleared the codes, and now have been driving for a month, no issues, no codes!
If these codes come up for other folks, try the easiest on the list first, before bringing to the dealer... these codes can be really hard to solve, but sometimes we can get lucky.
Camry :: 2008 LE V6 - CEL And Codes P0174 P0171
I just did an oil change at my vocational school on my grandpas car, 2008 LE V6. On the way back it threw a CEL. Codes are listed in the title. Now googling those codes i found info on other car manufacturers i.e ford, dodge etc.. But i found nothing in regards to a gen 6 camry. It seems like this code has something to do with the engine running lean. Bank 1 and bank 2. What could cause these codes and what could be a possible remedy. P0174 and P0171 were both pending and setting a cel don't know if maybe they were pending before i did the oil change.
View 14 RepliesFord - Taurus :: Keep Getting Codes P0171 And P0174
I have a 1996 ford taurus lx dohc v6 3.0.. I keep getting codes p0171 & p0174 System Too Lean (Bank 1 and bank 2. I check for air links and i did not find any..I never got that code tell i replace the MAF sensor..
View 7 RepliesFord F-150 (2004-2008) :: 2005 - Got Codes P0022 And P0345?
So I have an 05 Expedition (I know this is the F-150 forum, but more visibility) that is throwing a P0022 and P0345. I get these point to the cam phasers, so before I throw $450 on a phaser kit and oil pump, I want to make sure its a good fix.
I have done a lot of research on this forum and other where people have replaced their phasers and it doesn't end up fixing the issue. So I just was looking to get some tips before I endup shot gunning parts.
Ford - Expedition :: 1999 - Error Codes P0171 And P0174
I have a 1999 Ford Expedition with 163,000 miles.The vehicle registers a service code of P0171 and/or P0174, lean mixture.The vehicle starts fine, but may stall or hesitate when first started or at red lights.While driving, there is no issue.
I just replaced the MAF sensor and the EGR sensor, but no change in the condition.In 2007 or 50K miles ago, the oxygen sensors were replaced. What could be the problem or solution?
Ford - Explorer :: 2001 - Too Lean Codes P0171 And P0174
Working on my son's 2001 sport trac. 200K miles but it has always been a great running truck.
I have two CEL codes:
P0171 System too Lean (Bank 1)
P0174 System too Lean (Bank 2)
I have found several issues so far, but have yet to get rid of these pesky codes.
So far I have changed:
- Intake Gasket - I had coolant loss which replacing this gasket fixed.
- PCV Valve and Hose - valve was damaged and the hose leaked.
- EGR Valve - Valve was leaking
- Fuel Filter
- Mass Airflow Sensor
The engine does appear to be running much smoother now, but the lean codes remain.
Ford - Explorer :: 2003 - Lean Codes P0171 And P0174
2003 Sport Trac. My car was not starting, told my fuel pump, replaced twice and nothing. Found out about inertia switch and changed it, now car runs.
Before this switch blew out my car was running perfectly, no check engine, nothing. Now i have changed my fuel pump twice and put a brand new fuel filter in and soon after i get lean codes P0171 and P0174. My fuel pressure is 60psi at idle and drops to 0 after about 30 seconds when the car is shut off.
A lot of my intake is new since i did have a vacuum leak before, so i do not suspect that is it, especially since this happened after the new fuel pump. I am completely stuck as to what i should do. And i get hesitation when trying to accelerate sometimes
Ford - Explorer :: Codes P0171 And P0174 - Lean Bank 1 And 2 Sensor 2
I have been getting a P0171 and a P0174 code lean bank 1 and 2 sensor 2. I have replaced all 4 censers the 171 is gone but I keep getting the P0174 and it only comes on when I am on the highway after driving around 10 miles or so i got a freeze frame of the data when it happen.
View 6 RepliesFord F-150 (2004-2008) :: 2007 - Throwing Codes P0012 / P0022 And P0345
I have a 2007 F-150 5.4L and it started throwing codes p0012 p0022 p0345 and would knock and make popping sounds after it warmed up but I could rev it up and it would go away for the most part but would come right back when I started driving it. I have since pulled down the front cover and made sure it was in time, replaced both cam phasers, replaced both vct solenoids, and replaced both cam sensors. Same issue after doing all of that. I have searched the internet and have come up with nothing.
View 3 RepliesPhaeton :: What These Codes Mean P0171 And P0174
So the check engline light came on, and i hooked up a basic OBD II reader to the car. Out came codes P0171 and P0174 and it read "system too lean (bank 1)" and (bank 2) respectively. What does they mean?
View 4 RepliesFord Excursion :: Check Engine Light Illuminated For Codes P0171 And P0174
Coming home from spring break towing the TT, the Check Engine light illuminates. Seems to be sputtering at idle, but otherwise OK, so we continued home.
Scanner lists the P0171 and P0174 codes. Ok, where to begin? based on internet info, started by cleaning the MAF sensor and throttle body. When I pulled apart the intake, noticed that the grommet which feeds the MAF in the air intake had become separated letting air bypass the MAF. Hence the reason for the codes.
If you get these codes, check the grommet for the wires feeding the MAF in the air intake to make sure it hasn't become separated from the intake. No more codes.
Ford F-150 - 1997-2003 :: Engine Service Light - Codes P0171 And P0174
2001 F150 5.4L Triton Motor. Everything seemed o.k. then got the Engine Service Light. Checked with reader and above codes only appeared. Read numerous articles/videos and pulled the PCV hose/boot assembly and replaced the whole thing with oem part. Visually checked for disconnected tubing = none found. After this and with the new hose assembly in place I performed a reset. With the scanner still connected restarted engine and read values: ST FTRM1&2 = -.08~+2.3, both oxygen sensor voltages are varying and the LT FTRM1&2 hang around +26 and +28.
From what I understand the ST seems o.k. but the long term is WAY OUT OF WHACK. Started it up again and took carb cleaner spray and covered all the connections I could see = no change in engine rpm. No cracks in the air cleaner body. Big plug to the MAF was inserted and plugging the hole. I am thinking of making a smoke "machine" and trying that or removing the hoses from the throttle body and plugging the holes in the throttle body and see if that clears them up. IF it does then connect one by one and keep checking the values. Lot more work but I am at a loss.
Ford F-150 - 1997-2003 :: 2002 - SES Light Came On - Showing Codes P0171 / P0174
2002 F150 - 5.4 ... So just bought this truck about a month an a half ago. No problems but the other day the SES came on. It is showing P0171 and P0174. And P0000 (almost forgot that one) was told that's generic though. Haven't really noticed a difference in the way it's running. Has been extremely cold here in WV but the only thing I can notice (or think I notice) is the gas mileage has gone down a little. After reading some on this forum I'm looking for a vacuum leak correct?
View 10 RepliesFord F-150 (2004-2008) :: Replaced Many Parts / Rebuilt Engine But Got Codes P0345 / P0022 Again?
I'm having the well known situation with P0345, P0022
Replaced both phasers, replaced cam sensor, checked timing (properly aligned), assembled back still running rough and rattling, used 10w40 oil,
Complete rebuilt engine, we did head work new seals and springs, valves are straight I had it checked out twice for assurance. New pistons, new rings, new bearings, new oil pump and seals of course. If I disconnect cam sensor Bank 2 it works fine but still runs a little rough.
- Replaced one tensioner due to gasket wear.
- I was told to check on alternator ground (it's missing I know cause it got broken and I haven't replaced that ground that goes into the engine.)
- I also was told change oil to 5w20 and filter (Not FRAM), add some lucas and it should be the fix.
- Also told to disconnect the oil pressure sensor and it would fix the problem but it will throw a code for that.
- I haven't replaced the timing chains I feel they're a little loose but they haven't jumped the teeth, so I guess they're good.
- I saw in one thread to move a teeth on phaser giving me code bank 2 (moved one teeth back and then one teeth forward but it didn't work)
When I first rebuilt the engine I was having the rough iddle then I scanned it and it gave me the cam positioning sensor code P0345, then after I replaced it problem got fixed and code was gone, I was using the truck for 2 days with no issues, then the problem cam back with the two codes P0345 and P0022!
Ford Super Duty (1999-2016) :: 2005 F250 - CEL Codes P0171 And P0174
My 2005 f250 5.4 with codes p0171 and p0174. I have replaced fuel filter, MAF, Checked for vac leaks by smoke and water test.
I don't have a way to check fuel pressure on this thing since it must have been to much trouble to put that test port on the fuel rail!!!
Ford - Explorer :: 2003 - P0171 And P0174 Codes - Rubber Elbow Begin To Collapse
2003 Ford Explorer, with P0171 and P0174 codes, common problem, as I have read. I pulled the cover over the engine off, and I immediately found the likely problem. There is a hose/connection that runs from the valve cover on the right side, about 6 inches behind the oil fill tube across and looks like it comes into the Carb. Where it turns to come into the carb is a rubber elbow. This elbow has a hole in it. Temporarily I have used electrical tape, but when I run the vehicle, I see the elbow begin to collapse. I believe the elbow is getting weak with age, plus the hole/tear doesn't work. Anyway, what i the part number, or what this is called. Hoping Advance Auto, or Napa will have it, just don't know what it is called, and can't figure out the part number. Otherwise I will pull it off tomorrow and take to advance and see if they can match it.
View 5 RepliesChevrolet - Tracker :: CEL Flickers Along With P0171 And P0174 Codes
My 2002 Chevy Tracker recently has been running poorly after consuming a 1/4 tank of gas. The check engine light comes on the scan tool reports P0171 and P0174 bank 1 and 2 lean(it's a 2.5 liter V-6). If I remove and replace the gas cap it runs better but not perfect. Once I use another 1/4 tank the symptoms return. I have noticed the cap is hard to remove lately. This has been going on for two weeks It's been to 2 garages one of them told me my catalytic converters are plugged up and wanted 2500 to fix .
View 8 Replies