Ford F-150 (2004-2008) :: FX4 Won't Start / Sputtering For A While
Apr 8, 2014
I have a 04 fx4. Was sputtering for awhile. The engine light came on. Now it won't start even with a boost. What it could be has 290 clicks.
View 2 RepliesI have a 04 fx4. Was sputtering for awhile. The engine light came on. Now it won't start even with a boost. What it could be has 290 clicks.
View 2 Replies2005 5.4L She would have a hard time starting before but after I replaced and fixed everything below she was running really good. Now back to sputtering, taking a long time to start and now not starting at all.
I have replaced; Fuel Pump, Fuel Filter, FPDM, Plugs and COP's, FRP Sensor, followed the power wire from the FDPM and found it corroded bad so I replaced it, also changed the ground location on the FDPM, I have checked all the wires from the FDPM to the drivers seat, checked all fuses.
I have power to FPDM and I have the diagram for the plug but how can I test (hotwire) the Fuel Pump without lowering the fuel tank? What should be the voltage coming from the FPDM plug? not sure about pin 1 & 6.
How can I test the FRP sensor? what are the specs for voltage?
I have an '05 5.4L 3V and I was way to trusting in how it was running. BTW, I change the oil every 3 to 5 and have only driven highway miles, albeit a lot of them...155k! I bought it with 40k on it but was not aware of the plug change issue until I heard about it off-hand. I let the plug change go cuz it was running so well. Bad move.
Anyways, a few weeks ago it began to lose power and I suspected that the PCM was retarding the timing for some reason. Before I could get to the shop, the thing went nuts on me at 75mph. Started shaking and sputtering and throwing cel codes. I shut it down and after 5 minutes re-started. It seemed fine and actually was running a bit better. Took it in and the code was the 0302. #2 cyl misfire.
They also said the compression was very low on that cylinder and slightly low on 1,3 and 7 as well. I had them change the plugs and the #2 COP even though they said I needed a new engine and then I picked it up. Now the engine barely runs at all. It shakes violently, where to go from here. What should I do now? New engine?
It started completely unexpectedly about a month ago when I was driving around 70kmh while cruising. I would get a few "jerks" of a sputter, then was able to drive a km or 2 before it did it again. I drove to a friends and he got in, and the sputtering episode was over.
Since then, I cannot simulate the way I was driving to make it sputter for any mechanic, but I have been getting sputter on and off the last month.
The one time I got in the truck and started it, put the truck in drive, and it sputtered for a few seconds. I wasnt driving at all this time. This was the only time It sputtered in a stading position.
Here are a few points to maybe, narrow down what happens.
-I am usually driving around 70-90kmh
-I am usually under no loads (not towing, hauling etc).
-My mileage seems to be getting worse.
-this was normally happening not only when the engine was warm, but when it was warm outside and I was driving it for a longer period.
-When I started driving my truck I calculated around 16mpg city. I am currently getting around 13-14. I was on the hiway for around 250 km and got 14mpg. Seems I get better mileage when puttering through the city than when I am on the highway.
I had the truck in to a dealer 2 weeks ago. They did an injector flush, new sparkies, number 5 coil, and took me for $780, saying the problem is fixed.
A few days ago, I was driving on the onramp to the highway accelerating around 90kmh and for around 4-5 seconds I was sputtering and jerking so bad I thought I was done for. The truck finally recovered and again, haven't had any episodes since.
The dealership says their electrician doesn't know what to do, and would need my truck for 4-5 days to try to see the problem for himself. I can only think, as a non-mechanic, that it is something to do with some sensor, possibly a fuel, and/or oxygen sensor.
2005 F-150
4.6
88000km
gas
I purchased a 2006 Ford F-150 XLT, 5.4 3V Triton. Last Thursday my check engine light came on, so I came to this forum and found out how to retrieve the code with out a OBD. It came up as a 0301 Misfire cylinder 1-10?
I went to the dealer and they said it was cylinder one, sold me a new plug and coil pack and they installed it for a nice $$$. On my way home it started to sputter again when you give it heavy throttle, I called they told me that I should change all the plugs and Coil packs, kinda makes sense but to have all 8 plugs and coils go at once it only has 83km on it.
2006 F150 FX4 5.4L, 118k miles... At highway speeds (45-50) and (55-60) as I am slightly accelerating it feels like the transmission or maybe ignition system is skipping a beat. Kind of feels like a small bump. I replaced spark plugs with motocraft about 35K miles ago and recently all transmission fluid via cooler line. Had some concerns about system flush so I just drained and refilled entire system via cooler lines. I have read that it could be my COP's ...
View 7 RepliesI recently bought an 04 lariat crew cab with 56K miles 5.4 and auto trans. Before i bought it i complained about an exhaust noise and acceleration issue at 40mph and 1100 rpm as well as the ac not being very cold. They replaced the exhaust manifold on the passenger side, coil pack on the #3 cylinder, a transmission flush, a flash drive update and recharged the ac. This seemed to take care of the problem but i mostly drove under 30mph and did not notice it. I took it on a few road trips, and country roads and noticed the problem of sputtering and shuttering between 40-60 mph's after decelerating and slowly accelerating. The problem occurs consistently with ac and over-drive on in the above mentioned conditions and mph range. Problem is less noticeable with ac off and have not noticed it at all with over-drive off. It feels like a limited slip kicking in or driving on dry pavement in 4wd. Tranny shifts fine through all gears in a straight pull of acceleration and even full throttle pulls. Problem only occurs after decelerating and slowly accelerating. I don't know of any codes as I don't have a code reader, but I have not had any check engine lights come on nor has the dealer mentioned any codes.
View 7 Repliesi have an 07 ford f 150 5,4 liter. at speeds between 45 and 55 it has like a sputtering and jerking loss of power. I had a computer hooked up to it and it said fuel pump replaced it but it is still doing it, what this might be.
View 5 RepliesThe ole 5.4l hit a snag today. I was on my way to fill her up and she started sputtering and damn near died! i filled her up and it was like nothing ever happened. Took her to AutoZone and the diagnosis was a Fuel Tank Pressure Sensor.
I have a connection with Bumper-to-Bumper to get the part for cheap but I'm not sure if i want to dive into either moving the bed or dropping the tank. I'd prefer to move the bed.
I have recently come across a strange problem. Only occurs after car has been turned off and sitting for 1-2 hours. Weather not affecting and sitting overnight, car starts normal and nice.
After the 1-2 hours of sitting, engine will turn over not the 2 or 3 usual times for ignition, but needing 10-12 times to finally start. Then it starts very poorly by making a sputtering sound and only idling at 200-500 rpms, instead of the usual instant 1000 rpms. This is very annoying and a few times the engine has turned over 10-12 times and didn't start at all. When a person starts the car up every 1 to 2 hours, say on a busy errand weekend, it pretty much occurs each time. When my wife uses the car just in the morning for work and at the end of the work day, it is not noticed for some reason....
Back in January I drove my excursion about 1 1/2 hours or so and my tank had about 1/4 left. I shut it off and went to start it about 15 min. later. It did start but was sputtering. I shut it off and it started back up and ran fine. Drove another 1/2 hour... Shut it off, went to start I and it would only crank. Sounds like it isn't getting fuel. I also tried pressing he gas pedal thinking maybe a faulty IAC but that didn't work. I waited 1/2 hour and it started an ran fine. has not done it since... Always had more than 1/4 tank left.
This past weekend drove to the same place pulling my trailer. No issues at all. Coming home I live at the top of a big hill. My tank was at 1/4. Backed the trailer in and unhooked. Shut the ex down and walked away for 15 min or so. Went to put it in the garage and it started and sputtered, it did clear up after a few seconds and idled fine. I then shut it off. Tried to start it again and it would only crank. Waited a few min. and it started and ran fine. Does this sound like the fuel pump giving out?
- I have a scan gauge a checked for codes.... Nothing
- Garage kept hardly sees rain.
- Just over 95 k miles
- Only other thing is both times this happened it had sea foam in the tank
Napa says that bosch is the OEM pump. Is there a difference between motorcraft and the Bosch? Is one better? Could this also be a symptom of a crank sensor going bad or a cam sensor.
Took it in to my local mechanic that also has a v10 excursion. He hooked up fuel gauges and a computer to monitor the engine and codes while driving. He said everything is well with in the range of the specs. He will drive I for a coupl days to see if he can reproduce the issue. Where do I go from here with out just guessing what's wrong?
6.4 diesel 2008 F250.... I have been having lots of trouble with low power and sputtering of this diesel truck . It almost seems like a fuel filter but I changed them out 2 times now and the same thing keeps happening . It has been a very cold winter here and if there was any water - it would freeze.
If I am going down the highway and it starts to sputter. I put transmission into neutral and shut motor off with key. Start it up and it's good for less than a minute or two and it's back to sputtering.
1996 Ford Taurus 3.0L EFI DOHC 6cyl...... Every time I try to start the car it want start less I push on the gas pedal... Then its start to sputter really bad then dies.. I put new spark plugs in and new spark plug wires.. I do hear the fuel pump turn on... Car has about 147000 miles...
View 13 RepliesMy F150 4X4 would not start a few days ago, after only having turned it off a few minutes prior. The gauges would sweep wildly and get stuck at various positions. I checked the fuses and they were fine, then unplugged the battery for a bit and it started back up. Occasionally it won't start and i'll have to disconnect the battery again to get it to start.
I'm still having some strange electrical issues though. The radio no longer turns on unless the ignition is turned to AUX. My back up alarm for going in reverse doesn't come on anymore. The gauges take at least 10 seconds to wake up after starting the truck. The dashboard blinker indicators will randomly stop blinking or making any noise. I was thinking it could be the computer, but could it be something else?
I have a 1998 Ford Explorer. It was running fine until last Mon. On my 3rd start of the day , it wouldn't stay started long enough to get into gear; sometimes it sputtered violently. I tried starting over the next 2 days with the same outcome so I towed it to mechanic. They replaced spark plugs, wires & started (because it was throw lower voltage than normal). It ran fine the short distance home. The next day, it started fine but sputtered in corners/lower speeds. About 12 miles into the drive, which was at ~60 mph, my auto died and wouldn't start again. What's going on? Could it be the fuel pump?
View 1 RepliesMy 2000 Ranger standard 4.0 4x4, started spitting and sputtering the other morning just when i was gone up hills then it would quit doing it. The other evening it got to where it don't idle, missing very bad, and wouldn't even pull itself up a slight grade, and the wife said there was flames and sparks coming out the exhaust. Now it wont even try to start, it just turns over. I put a different coil pack, wires, and plugs, and still nothing. I pulled the gas line off the frame fuel filter and its shooting gas out, and I got gas to the check port on top of the engine.
View 5 Replies2005 Ford F250 6.0 Diesel (bought new). Never had a problem with the engine until about a month ago. Engine has 220,000 miles on it. Oil and filters changed regularly. Ran low (not out) of fuel, started sputtering badly but not killing. Filled up with diesel. Ran better, managed to get home. The next day it was dead. Crank but no start. Since then I have done the following (not in order):
- Changed EGR
- Changed ICP
- Changed IPR
- Changed the STC fitting
- Changed all seals in the HPOP
- Changed glow plugs and harnesses
- Tested each fuse and relay
- Installed new batteries
- FICM tested 48V
- Changed motor oil and filter
- Changed both fuel filters
- Checked for water in the fuel
- Purged air from fuel line
- Replaced dummy plugs
- No codes
- Prayed the rosary
One month later, still crank no start. Thinking about using it as target practice with the AR-15.
I was told by the dealer it would be over 150 to scan and do a fuel trim on my 02 Explorer, XLT, 4.0, Auto. I can't afford the scan or a garage. I paid 4200 for it and a short time later it starts surging at stop lights then it starts sputtering when idling and taking a while to start. Next it stops accelerating past 2.5k, then works well a bit then stops accelerating past 50 miles an hour. Then it works with an 02 disconnected then starts acting up again. It now either runs normal, wont accelorate past certain ranges, or starts then quits 3 seconds later, unless I unplug the MAF then it runs 15 seconds then stalls. Through all this symptoms come and go. Always banks 1 and 2 lean.
Symptoms
Knock
Rough Idle
Slow Starts
Hesitation
Lag
Stall
Replaced
02 Sensors
Fuel Filter
Injectors
Plugs
Plug Wires
Tested
Maf
TP
Temp Sensor
Cam Sensor
Crank Sensor
All EGR Components
Idle Valve
Coil Pack
For any air leaks.
Fuel pressure 37 or higher
Clean Fuel Pump Strainer
Flow tested pump
Checked air filter
I have had a problem where truck would start jerking and sputtering in a certain town at low speeds. Today it happened in a new place. Barely got it to start back up. Was running rough after the puff of black smoke. Its stranded at a gas station. Recently replaced my sending unit. Was running good. Clean gas tank. Fuel lines tight. Where should I begin? I have an ICP sensor in the glove box. Truck wouldn't start.
View 8 RepliesOk so... have an 04 that has more issues than Playboy magazine... any DIY tips or tricks...
I dont have an original key but the key I have has worked before. Motor cranks but wont turn over. Have tried the battery unhook thing, didnt work.
I have a 2005 F150 XLT 5.4 that doesn't always start. I've been having this problem for over a year now.
Sometimes it will start, but sometimes it won't. Seems about every other, or perhaps every 3 days it just will not start. Then, if I wait a few hours, it'll start.
I've replaced the fuel pump, fuel filter, mass air flow sensor, fuel pump driver module, starter and the battery. None of this has seemed to effect it.
Lately I've found out that if I put the truck in neutral, then while cranking I go to park (going through reverse) it will start. Sometimes not on the first try, but after a few attempts it will start.
It should also be noted that when it does start, often it'll make some loud noise RIGHT before it starts up. Sounds kind of like the starter grinding. If it doesn't make the grind noise, the other thing it may do is all the lights and everything turn off for an instant (half a second) then come back on and start.
I'm really lost as to what to do. I've been thinking that it may be the transmission range sensor, but I really don't know. I don't want to keep spending money replacing random parts, in hopes of fixing it. I'm on the 3rd starter, because of all the cranking I have to do when it doesn't start.