I have an 04 F150 Lariat with the 5.4. I get alot of noise out of the top of the motor. I hear lots of stories of sludge issues, is that the problem or do I need to have the motor gone through? the knock is not horrible but when the motor is warm the noise is pretty apparent!
View 3 RepliesI have a 2007 F-150 4x4 5.4L. I recently had a problem with my engine. It had the knocking noise thats known for the 5.4. My issue is i replaced the engine (it had 275,000 miles and was a work truck before i bought it) As well as all the timing components including the hydraulic tensioners, new phasers, new guides, new solenoid, and a new camshaft positioning sensor and it still isnt fixed.
View 3 RepliesGetting these codes what they mean or need to do ..to get rid of them...p0022, p0171, p0174, p0183, p0340, p0300, p0316, p2006 did timing n plugs fuel filter n gas filter getting very bad gas mileage it runs good but here a ticking in motor at idle and more as u accelerate, running rough....
View 7 RepliesToday I decided to do some maintenance on the truck as it needed an oil change and some other unrelated misc stuff.
1. I seafoamed the engine thoroughly. I bought two cans of this stuff, half of a can went into the fuel, another half can in through the brake booster vacuum hose, and I dumped a full can of into the oil. Took it for a 30 minute drive, let the ol' gal smoke as it usually does on a seafoam, and then changed the oil. No noises, I noticed immediately improvement in acceleration.
2. Upon intial startup after the oil change, I thought the motor was coming apart. It was only for about two seconds, (i was counting to make sure) if it didn't have oil pressure and no noise by 3, I was shutting it off. It hasn't done it since.
Is it possible I just knocked some crap loose in the heads causing the oil drain a lot faster into the pan than I expected? I'll try it again in a few hours after everything has cooled off and oil has drained back into the pan, but I wanna make sure I didn't damage anything. Still drives good, no problems, no noises since.
The last oil change I did, I didn't do a Seafoam, but I figured with winter coming it's a good idea to get her running in top form. I used Pennzoil Platinum 5w20, with a Motorcraft oil filter for those wondering.
Truck has 133K on the clock, and it's had the slight cam phaser tick since I've purchased it, no other problems. I bought it almost a year ago.
In this video I go over in detail the procedure to swap out the Cam Phaser to get rid of that annoying knocking noise at idle! It is easier than you think. The procedure is the same for all 4.6l and 5.4l 3valve engines.
Ford 4.6l 3v & 5.4L 3v Camshaft Phaser Knocking Noise Fix - YouTube...
I have a 2004 F150 Lariat Supercrew 4x4 . I got a new transmission put in and a Oil change shortly after. A few weeks later I got a knocking noise. No check engine light, starts up great, No real notable problems just the noise. At Idle no noise just the usual cam phaser ticking, but once the engine is warmed up at about 1100 RPM it starts knocking like a . I took it to a few different shops one was sure it was the timing area so they replaced the timing chain, tensioner, pully. ect. Took it to a ford dealer where he didn't really look at it just said you need a new engine.
I went to another ford dealer where they said rod knock or stuck lifter but if that were the case shouldn't it knock constantly? another shop said VCT soleinods, Spark plugs. another said it could be the flex plate! I'm aware of the cam phaser diesel ticking noise they notoriously have but thats not it. I've parked it for a few years to be safe but started it weekly. I didn't intend on having it sit for so long but due to work situations and what not it has sat but now I'm on a mission to make it my daily driver again. I'm no mechanic but I'm not totally green to vehicle mechanics so ill be inspecting what i can within my limits.
YouTube video : [URL] .....
I have an 05 f150 5.4 v8 super crew cab and I bought it for 3000 because of a cracked block. I bought a re-manufactured engine and installed it and now i have a knocking that wont go away. After I started it up it sounded beautiful for about 10 minutes and then i had a knocking start up. I have put about 30 miles on the new engine and still have the knocking. I let it sit over night and I started it up and there was no knocking so i drove about 3 miles to the gas station and by the time I got there the knocking was back. it runs fine no other issues but why do I have this knocking with a new engine.
View 9 RepliesI have a 2004 F150 with a 5.4L with a little over 100,000 miles. And the engine knocks like it about 1 1/2 quarts low on oil! I'm not a mechanic by any means, but I'd like to know how to get this fixed. I've actually had 2 different people ask how I got a diesel engine in a 1/2 ton truck!
View 11 Replies5.4. So I have a 2004 F-150 that just passed 80,000 miles and a month ago it started making a very loud noise on startup, but only cold startup, meaning if I haven't used the truck in about three hours. Now I went on youtube to research and found a video of a truck making the exact same noise! Here is the link:
2004 f150 cold start knocking noise - YouTube ....
Need to verify what this is??? Some people are saying cam phasers and some are saying I'll need a brand new engine!
I have a question about my 2007 F150 4x4 with the 5.4L. It has a ticking noise sound coming from somewhere around the motor, but it's not there till the motor has warmed up. It almost sounds like a exhaust leak, but I'm not sure. What it might be, or what to look for?
View 11 RepliesI have a 2006 f150 it was making a knocking noise after the engine oil temp reached 160* and made the noise to 1700rpms. I thought it was the cam phasers so I replaced them. The truck is still making the noise and running rough and stalling but not as bad and not as often. Before it did it all of the time. The truck is timed properly. I had a new cam sensor and tried it but that did not work. I watched vct on the scan tool and both cams are in sycn.
View 2 RepliesHaving issue with his truck. He bought it 3 months ago and has no history. 166k. You now know as much as I do about the truck! He knows little about automobiles so fact finding has been difficult. I have done all my own work on countless US and foreign automobiles over the last 30 years and never take my vehicles anywhere. I will try to post as much detailed info as I can. I have read tons of posts now on various forums so I am up to speed on VCT and phasers.
This one seems similar, but not exactly the same symptoms which is why I am here. I have already pulled the VCTs and found the passenger side missing the top screen. I swapped them from side to side which made no difference. I checked ohms and they were at 15 which is normal from what I read. They were very clean and moved easily when I took them out so they were not gunked up so I don't think that's the problem. It idles very smoothly and isn't rough at all.
I have posted a video of the knocking/dieseling noise (link below) coming from the passenger side. The knocking starts as soon as the truck is started hot or cold (outside temps right now 70F-90F Houston). I can make the knock disappear by gently depressing the gas pedal going from idle of about 650/700 to maybe 750/800 and it will go away completely as long as I keep it gently depressed. As soon as I lift up it returns.
If I rev it up to 2000-3000 rpm it does not knock, however, as soon as I lift off quickly, it seems to knock at a high speed, hangs for a second and then knocks all the way back to idle. However, if I rev up and then lift off very slowly, it will not knock. I have tried to locate the exact location of the knock, but doesn't exactly seem right at the phaser, but actually back around the 2nd and 3rd spark plug area, but I can't tell exactly. I've had a couple people tell me the same when I asked them to tell me where its coming from. The noise is bouncing around in there so difficult to pinpoint exact area.
[URL] .....
I wanted to get some second opinions on what this could be so I know where to go next.
[URL] .... My engine has been making this sound for a while now I am at 125000 miles, what it could be and if i need to be worried about it? also, possibly unrelated, it has a SUPER hard time shifting into reverse, it gets stuck and it feels just super sticky shifting in and out of reverse. Sometimes I can't even get it to go into reverse without letting the car roll a bit. Also, at around 3k rpm the engine sounds a little grinder in any gear. 2008 Honda Fit Sport ...
View 19 RepliesI've had this strange knocking noise ever since may coming from my motor. I thought, it might go away if i push the car a little. But it's been 6 months, and the thing is still going hard. What I'm experiencing is kind of a knocking noise, something akin to marbles being shaken up in some kind of jar, and it is only at partial throttle. Starts at 2000 rpms and goes all the way until redline. What it could be? Engine sounds perfectly fine at idle, power is still there. MPG's are the same... I've also read a couple threads that indicate that it could be my intake manifold, I am really not that good with cars, shameful but i admit.
Btw while i was browsing found a repair manual on the net [URL] ....
Okay just installed a newer 24v into my existing 24v VR6 GTI both with 135k. I have heard the motor run before it was pulled and sold to which sounded fine. Upon receiving the motor I put new timing chains, guides, headgasket and new gaskets all around. The timing was right on the mark and I tightened everything up to torque spec and I'm getting this noise which sounds like it's from the timing cover area. A code just popped on which I'm going to scan as soon as I get my hands on one. The car was running great for about 20 minute and I shut it off then turned it back on about 5 minutes later and experiencing these scary noises. I tried pulling each individual coil with no results to get the noise away. What could this be?
[URL] .....
My girlfriends 2010 Golf 2.5 is worrying me. We went on a weekend vacation to Boston so the car sat for 3 days. I go to turn it on tonight and it just immediately stalls. I was like okay thats weird so I turn it back on and instead of stalling, the RMP gauge keeps dipping and then going back up and theres a strange knocking noise, so I turn it off and then decide to try again. Same thing happens so I go to open the hood and the noise is pretty loud. I noticed a strange smell outside the car while the motor was running, but I can't really explain it. So I turn it off for about 2 minutes and then start it again and its just back to normal, I'm so confused. I drove it about 5 miles and it seems fine, aside from idling slightly rougher than normal. What this could be?
View 11 RepliesI have a 2000 celica gt... My motor is making a loud knocking noise at all time.. The other day it completely stop working. It started back after a couple of attempts... I think I need a new motor but idk... What kind of motor will fit and how much or what can I get for the car if i sale it..
View 2 Repliesit was warmer the day than it usually was so it dosnt make the noise as bad however there is usually a lot of clatter/knock from the engine when cold. does it at idle and while accelerating. it gets less once the engine warms up but has been doing it for a while. car has 93k miles and synthetic oil is used. there is also a metal rattle sound almost like a heat shield that is loose. idk if that is part of the engine issue or not. but it only happens in winter or when temps fall below 60 degrees. kinda hard to hear on the vid but its there.
View 19 RepliesSometimes when my car as sitting at an idle in either drive or reverse the motor starts to make a knocking noise from the back of the motor towards the firewall side on the top of the motor. I have a video. The car has 114k I just changed the oil I thought maybe it's low but it's not and hasn't moved since it was changed.
View 4 RepliesI got a horrible clunking/knocking in the front end of my pickup this morning, jerking the steering wheel like a flat tire, and after a couple miles it stopped..... bearing ???
View 7 RepliesMy truck is idling terribly and knocks while doing so, little info is
The truck has 170k miles, I just bought it about two months ago and it was running perfect, drove it to the beach two or three times (4 hour drive) no problems whatsoever. Two weeks ago I noticed it start rocking a bit at idle ONLY when warm, check engine light came on so I ran the code and it said the Cam shaft positioning sensor was bad so I replaced both of those, then the next code I got was for the vct solenoids, replaced both of those and the problem is still persisting. It is odd to me in the fact that when its cold, it runs flawlessly, no problem accelerating/idling/maintaining speed/smoke nothing at all.
As soon as it gets warm it will still do everything flawlessly EXCEPT idle. the idle rpm is around 300-400 and it rocks and knocks terribly.. If i am stopped and I apply some throttle in park or nuetral, just enough to get the rpm up to around 800-900, its perfectly fine. no more rocking no more knocking but as soon as i let my foot off the gas it goes right back to feeling like its going to fly out from underneath the hood.
So my question is why is this? What on earth is going on here? and how do I fix it? And why is there not a manual idle control. Ford place said there was likely damage to the head and recommended a full engine replacement.