At 2:30am this morning I looked out my window and saw my brake lights and third brake light come on for about 5 seconds and then go off. This scenario kept repeating itself. I went to drive my truck 2007, and the brake lights remained on even when the lights were turned off when I was driving. I also need to seal the third light. Brake regulator has been replaced.
View 2 RepliesThis morning I drove down to unlock my gate and got out of the truck while it was idling. When I got to the gate the truck just stopped running it did not sputter or anything it was like a light switch and just shut off. I got back in the truck and tried to start it but nothing happened starter did not engage at all or even try to run. I put a new battery in it knowing that is not the problem but it will just not start or even turn over.
View 1 Replies2000 passat GLX, tip, 2.8L v6... new brake pads and freshly turned rotors, but both the "ABS" light and the "BRAKE" lights come on intermittently whilst driving. It doesn't happen every time it's driven, just maybe 1/3-1/2 of the time, and it is only on for a bit before it turns off, but it will usually turn on again later for a short stint as well.
View 3 RepliesOn my way into work this morning, my 06 with the 5.4 started running very rough/shaking at low rpms. I could kick it out of overdrive and it would smooth out and seemingly be fine at higher rpms.
This worked out for a couple of miles until the truck just died on me completely. The Edge is showing po351, 352, 353......358 codes. Ignition coil Primary/Secondary circuit fault on every cylinder.
I'm thinking its unlikely that every coil failed simultaneously....computer? When I try to start the truck, it will try to hit on a cylinder or two, but will not run.
First it was the whole spark plug debacle. Now it's the "fuel pump module". Story starts a several months back. On a moist day I was headed out and the truck ran very rough, "clunky", like it wasn't getting gas. After 15 miles and a stop truck ran fine. Didn't think much of it and truck ran fine for month or so. I was then away for a couple days and came home to find my truck wouldn't run (started briefly then died). Local mechanic thought it might be a fuel pump issue but then got truck running thinking it might have been a delayed inertia switch in front panel (I had hit a deer a week or 2 prior). Again, not thinking much of it continued to drive truck with no issues for awhile. Then one rainy morning on my way to work the truck was running very rough and "clunky" again. It died several times and finally for good.
After getting it towed to the mechanics, he figured the fuel pump was finally shot. The end to my long story is it was the fuel pump module (luckily a lot cheaper fix than the fuel pump) - half of the housing was gone (corroded away) adn moisture was shorting the pump electronics. Why, if this module is half encased in plastic do the engineers feel the need to encase the other half in metal (appeared to be cast aluminum)??!!????!! Of course it makes sense to have an electrical unit that is mounted underneath the truck where it can collect all the moisture, snow, salt from the road encased in a corrodable metal housing. No no, don't put it all in plastic, just half of the unit. MAKES PERFECT SENSE!! I thought to be and engineer took some sort of brains and common sense. Must be not at Ford. I can't be the only one with this issue and wondering WHY!!! - it must be widespread??
Began doing this on sunday and just finished up last night. Truck starts and runs for a bit then stalls. Here is what I did in this order:
1.) Washed truck sundday with purple power and a garden hose. I washed the wheel wells frame and underside, but DID NOT wash the engine at all.
2.) Painted the frame and wheel wells with black paint.
3.) Applied 1/2 gallon or so of fluid film all over the bottom of the truck everywhere I can. Again NOT the engine bay.
Where to start. When it stalled, I can restart every time by waiting 3-5 minutes. It was 13 degrees F last night, so i suspect fuel lines may be freezing but not sure.
I just bought a 2006 f150 exteneded cab w/ 5.4 V-8 and it vibrates when accelerating from a stopped position but not all the time---happens more when the wheel is turned. It definitely feels like the vib is coming from the left front side. I just got it back from the shop and the mechanic told me the vibration was stemming from the rear and that he exhchanged the fluid and added anti-friction additiver but that he expects the problem to continue.
View 4 Replies2008 F150 5.4L .. The truck lost all power the other day driving and barely made it to work. On the ride home it was still running horribly, like it just fell on its face. the check engine light came on. Went to autozone and put HEAT in the gas tank cuz the night before it was at quarter tank and temp went from warm to freezing(thought maybe condensation in tank).. Truck ran a lot better( not perfect). Drove around that day and it was fine. Pulled down the driveway and CE light shut off. Ran the code anyways and it was P0012..
Talked to a few mechanics and they said try replacing the Camshaft position sensors..did so and it ran worse. the truck hardly would idle or rev and shook violently..i shut it down right away. Then it threw 9 codes..Cam shaft position- over retarded timing bank 1(P0012), misfire cyl2, misfire cyl3, misfire cyl 4, random misfire, cam sensor bank 1, three of them were repeated codes..
I replaced the sensors back to stock and cleared the codes. the truck is running like it was in the beginning of the problem..No vilant shaking but falling right on its face at idle and any rpm..not drivable. Would rather do the work myself. very capable except for replacing camshaft phasers which i have heard could be the issue..Could it by the VCT seliniod, EGR valve, plugs, wires...Did just change the oil a week ago and cleaned and reoiled air filter.
I have a 2004 f150 fx4. My running lights on my trailer will not come on. Brake lights work, turn signals work, back up lights work. Had my boat mechanic check the trailer and that showed that the lights work fine. So I started checking fuses on the truck. Fuses all looked good. Then I went into the Auxiliary Relay Box in the engine compartment on the left fender. In the spot marked Trailer Tow Park Lamps (R201), theres no relay. R202 is for the Fog lamps, same relay. I pulled the Fog Lamp relay out and went to put in R201 for Trailer lamps, but there's no contacts in the R201 slots. The relay goes in with ease and just falls out. No contacts. Whats going on?
View 2 RepliesThe running lights and marker light on my trailer no longer work when I connect to my 2008, F150 4x2 Supercab, XLT, 4.6 V8 Auto with Tow package. Brake and turn signal work fine. The running lights, all the lights work on the trailer work when I connect to my Chevy so I know the problem is in the F150.
I have confirmed the ground to the 7 pin and 4 flat connector is good so I am thinking it must be a fuse or relay. Which specific fuse or relay should I check or replace?
What should the idle be at for a 2004 f150 fx4. When I first start the stuck it jumps to about 1200 or so and then after a few seconds settles at about 500 and stays there at all stops. It seems to be smooth but when I let go of the brake, the truck doesn't really want to move forward. It is a crew cab so I know there is some weight there. If anything is wrong, what are some possible fixes.
View 3 RepliesI have a 2007 f150 pick up and all of a sudden my running lights (front and back), dashboard lights, fog lights and plate lights stopped working. I ckecked all the fuses with a voltmeter and all are working.
View 4 RepliesI recently got my truck back from the dealership 04 super d 4x diesel (wife put gas in).. Anyway my dash lights, running lights and brake lights are not working. I checked fuses already and I did not see any obvious problems. I also replace the switch but that didn't work. Perhaps a ground somewhere or a relay? Turn signals and headlights work.
View 1 RepliesDriving home my radio quit working. I looked at the gauges and they all dropped to the left. The it looked like my lights quit working and then the truck just quit. All of this happened within 5 miles and 10 minutes. I jumped it and quit before I could even get going, it did start momentarily. Could not even get the gear shift into neutral; had to jump it to get that to happen.
It is 2006 F150 4x4, 5.4L engine and about 95,000 miles.
My brake lights dont come on until they are completely depressed. I think it may be the switch that connects to the pedal, but how do i adjust it in such a way that the light will come on sooner so everyone will quit telling me my brake lights are out?
View 2 RepliesMy cruise and brake lights went out last night on my way home. My horn still works and fuses are good. I'm stumped.
View 2 RepliesI have a 2007 F150 that it's brake lights and turn signals have gone out. What's wrong? I've checked fuses and connections.
View 1 RepliesThe brake and turn signal lights on my 04 f150 quit working. I've replaced all of the fuses and relays I could find from the owners manual. The windows have also quite working. What may be wrong?
View 9 RepliesSo, I installed a new radio lately (Poineer 4100 NEX- nice radio, BTW). Yesterday, I ran a couple video wires through the firewall for new backup cameras. Anyway, after I was done, my brake lights and cruise control didn't work.
After a little Googling, I decided it my have something to do with the electrical switch on the brake pedal. So, I wiggled the brake switch a bit and the brake lights are working again. I must have bumped or bent something while I was running wires.
Was/is my switch out of alignment or is this a sign my switch may be going out. Should I replace the switch?
I have a 2006 King Ranch and right tail and brake lights don't work. The bulb is good. The fuse diagram in the owners manual is not the fuse box I have, so I cannot id the correct fuse to see if its bad.
View 4 RepliesI was using a 2004 Heritage F150 and when I connected a trailer to it something got fried. I lost both my turn signals and brake lights. The trailer worked fine on my friends truck so I don't think the issue was there but with the 4-pin round connector that was on the truck.
I found two 10A fuses blown under the hood and replaced them but that didn't work. They were in slots 19 and 20 and are listed as the camper/trailer adapter fuses. The running lights still work. The interior turn signal arrows don't even light up or anything when the turn signal is activated.