Ford F-150 (2004-2008) :: 5.4 Engine Has Top End Noise On Right Side And Runs Very Rough
Jun 6, 2012
2008 f150 5.4 30,000 miles the engine has top end noise on the right side and runs very rough no codes cam problem ?
View 4 Replies
Jun 6, 2012
Advertisement
Ford F-150 (2004-2008) :: Runs Rough At 60 Mph?
Before and after this speed it runs fine, so what could it be. The check engine light is now on all the time.
View 2 RepliesFord F-150 (2004-2008) :: Runs Rough And Idles Poorly Only When Cold
I recently replaced the plugs cuz I had a rough idle all the time. During plug change when I discovered they had already been changed I found one that had a burned off electrode. Does this mean a lean condition exists?
After plug change it runs smoothly but only after 10 min warmup in our canadian winters. I can drive it when its not warm but seems to have less than full power and idles very badly after driving w/o proper warmup.
Next I changed fuel filter and checked fpdm, it was a little rusty but not bad so i just mounted it 1/4 off steel to prevent further rusting.
Since then I have installed a programmer [diablosport] but found no codes since i had battery disconnected for filter change. no new codes in last few weeks since.
So do I have a lean running cylinder causing this poor cold idle or a rich cylinder? It must be a clogged or dripping fuel injector right?
Ford F-150 (2004-2008) :: Check Engine Light Flashing - Running Rough With Tapping Noise
2005 F-150 4.6L 2WD, 268,000 miles....
Recently I got a flashing 'Check Engine' light and a rough running engine (along with a tapping noise) when I was passing someone (and pulling a trailer). I retrieved codes 300, 304, & 305. I can't swear to it, but I think the tapping noise started at the same time as the coil problem.
I replaced coils #4 & #5 (later that same day) and the engine smoothed back out but the tapping noise is still hanging around. The noise speeds up at higher RPM's and doesn't go away if I shift into neutral. Oil level and pressure are fine and I only use Motorcraft 5W-20 and Motorcraft filters (and change the oil every 5K miles).
Not sure if this is relevant: I think I have bad valve guide seals (blue smoke after long idles) but no other problems that I am aware of. It sort of sounds like a lifter, but is there a good way to pin it down? Is it possible that this tapping is related to the bad coils?
Ford Ranger / B-Series :: Runs Rough - Driver Side Exhaust Manifold Cold / Passenger Side Hot?
1990 Bronco II, 2.9l, auto, 4x4. Was running just fine. Sitting in Park just idling away. All of a sudden, just starts running real rough, ticking, etc.
Towed it home. This morning, started up OK but still running really rough.
While running, pulled spark plug wires one at a time from the drivers side. Had no effect but could tell the wires were sparking as I held them up to metal.
Turned truck off. Drivers side exhaust manifold COLD, passenger side HOT.
This sounds real bad to me. Am I missing something simple that could cause the drivers side of the engine to not work?
Toyota - Corolla :: Runs Rough And Lifter Noise As If There Was No Oil In Engine At Times
The engine problem I am having is with a 96 corolla with about 198000 miles on it it runs rough and has lifter noise as if there was no oil in engine it only happens when cold and when the vehicle has sat for more then 3 days since last use.....
View 2 RepliesFord F-150 (2004-2008) :: Rattling Noise Coming From Passenger Side Of Engine - Low Compression
My 2004 F-150 5.4 has a rattling noise coming from the passenger side of the engine when at operating temperature. The cam phasers and all related parts have been replaced. The reason I was prompted to change the phasers, chains, guides and tensioners was due to the engine stopping on me as I returned home from an errand. The engine had already shown signs of needing the phasers replaced.
The engine runs very smooth while warming up. Vehicle lacks power and has a rough idle after warm. Took the truck to a local mechanic, in the process of making a diagnosis, he performed a compression test. Cylinder 3 psi was much lower than the other 7 cylinders, the mechanic recommended replacing the engine (possible bent valve).
I have a Haynes manual, have searched youtube and checked this and similar forums, I have yet to find instructions on the removal of the head from the block.
(2004 Ford F-150 5.4 3v)....
Ford F-150 (2004-2008) :: 2007 - High Pitch Whining Noise On Front Right Side Of Engine
My 07 SCREW 5.4L 4x4 has 77,000 miles and has a high pitch whining noise on front right side of engine. Sounds worse in the cold,increases with RPMs.
View 5 RepliesFord Ranger / B-Series :: 2008 - Runs Rough With No Power
I just changed the plugs and wires on my 2008 Ranger 3L. Now it runs rough with no power. It was fine before I did the work but I thought I should change the plugs at 215000KM. I used Ford wires but unfortunately I used Bosh platinum plugs and now think I will change to Ford plugs. Do you think the Bosch plugs would be that bad for the Ranger? What is the belt tensioner torx size? I had to move the A/C compressor over to get the #4 plug but had a very hard time trying to loosen the belt.
View 7 RepliesToyota - Corolla :: 2008 - Engine Runs But Car Does Not / Loud Grinding Noise
I was driving my car today, and I stopped at a stop sign. When I went to go, I pushed the gas, and my car revved up, moved forward, then all of a sudden it made a loud grinding noise (Like I was dragging metal sheets), and the gas stopped responding (but the engine was still running). The car still turns on, but whenever the gas is pushed, it doesn't go and makes that awful noise. What could be wrong?
View 2 RepliesFord :: Engine Will Rev Up But Runs Very Rough And Lacks Power When Driven
I have a 1994 Ford F-150 pickup with a 4.9 litre fuel injected inline six. Truck ran fine and took me to my destination but after sitting for 4 hours the truck would not start. Engine would turn over normally and could hear fuel pump running (didn't seem to stop) but truck would not start.
I changed fuel filter but truck would still not start. I removed air filter assembly and poured starting fluid in the air intake and engine started but idled roughly. Engine will rev up but runs very rough and lacks power when driven. Also the check engine light stays on.
Ford - Lincoln :: 2004 - Rough Idol But Runs Smooth When Gas Is Given?
My 2004 Lincoln navigator is very rough at idle but runs smooth when I give it gas. Someone said my VCT may be stuck or bad. I looked at Youtube videos of VCT replacement but in all the videos the VCT's are up front in the valve covers. On the Navigator they aren't there. Where the heck they might be located?
View 2 RepliesFord F-150 (2004-2008) :: Rough Idle When Engine Is Warm
I purchased an '08 F150 about 6 months ago, and have a problem that two mechanics haven't been able to solve. The truck has a 5.4L engine. Unfortunately, I bought from an auction and the 30 day warranty expired before I realized the problem.
After a longer drive (30 minutes to work) the engine is warm, and I always back into my parking spot or driveway. In low gear, it begins to idle very rough and the engine shakes. If I leave it long enough, it will stall. Usually I pop it into neutral, give it some gas, and its fine. I just bought a camper trailer, so I'll need to use the lower gear when backing up.
So far, the engine has been flushed twice, the solenoid replaced and phaser replaced. The second mechanic has recommended I contact a dealer, but haven't had luck with them with my previous Explorer. What it could be? I will be getting the diagnostic paperwork this week.
Ford F-150 (2004-2008) :: 4.6L Engine Hesitation And Rough Idle
I have a 2008 Ford F150 4.6L and its been broken down in our shop for quite some time now. It started acting funny when I could not get the truck to do over 80kmh. Slow acceleration, and a horrible shaking when it idled. Eventually it was undriveable since I could go above 50kmh anymore. From looking online we replaced the plugs and coils. We removed the intake to find the gaskets were shot so coolant was leaking into the spark plug tubes which could've been the cause of a misfire. Fixed that. Still the same. We replaced the egr valve and dpfe sensor because we keep getting the P0402 excessive egr flow code. Still no luck. My dad is a journeyman hes just not too familiar with newer trucks.
View 4 RepliesFord F-150 (2004-2008) :: Rough Idle And Hissing Noise At 1800 RPM?
have been lurking the forum for the last several months ever since I bought my 2008 F150. I bought it used from a dealership and have had it at their shop no less than seven times since I bought it in March, all for the same things.
The first thing I noticed shortly after buying the truck was that after the truck warmed up it would idle rough. My chief complaint by far, I took the truck in to be looked at and this is when all the real fun began. Similarly I had intermittent power steering that I asked to have looked at.
I was told the fuel filter was completely clogged. They cleaned it and assured me all was well. They also bled the power steering system because apparently someone had changed the PS pump and not bled the system afterwards. I got into the truck to leave and it was idling no better than when I dropped it off. I complained again and was told that "this is just how this truck idles" and called BS. They offered to have the throttle body cleaned for me the next day to alleviate any remnants of rough idle.
Had the throttle body cleaned the next day and took the truck home. After about an hour or two I was still thoroughly dissatisfied with the idle and called back to complain. I forgot to mention that I bought my truck from a Chevrolet dealer who had just taken it in on trade about three days before I bought it. Because I complained they offered to send the truck to a Ford dealership for further diagnosis.
The Ford dealership found fouled plugs, a cracked intake manifold and the water pump and fan clutch both had excessive play. They said those would create a rocking sensation which could be misinterpreted as a rough idle. Over $2500 the Chevy dealership paid them and I was called to come pick up the truck.
I didn't even make it out of the parking lot because the truck was whining something fierce. I couldn't believe no one QC'd the vehicle and complained again. Next morning I am called and they said that the Ford dealership had put the intake manifold gasket in wrong and it had been corrected and I could come pick up the truck.
I go pick up the truck and note that not only is the idle still not right, but now the truck is making a hissing/squealing noise when the truck hits 1800/1900 RPM's. Its strange because its not really RPM specific as it is specific to the pedal position. Accelerating or decelerating causes it to go away but its there nonetheless. Whats worse is that in highway driving at 65 MPH, the pedal is in just the wrong position and it hisses constantly. This sound never goes away...and once its been heard its impossible to unhear.
I complain again and they send the truck back to the Ford dealership. At this point I'm dealing directly with the Director of Service because mine has become a high priority case. The Service Director drives with me, confirms my problem and takes the truck himself to Ford. He drives with their shop foreman and they too confirm the problem.
A week goes by and Ford tells him its wind noise. This is complete bullarky because it happens whether I'm going 20 or 65. He calls them on it and they keep the truck another couple days. They call back and say the truck has nothing mechanically wrong with it and that they are done. Service Director goes and picks up the truck and takes it to a second Ford dealership.
Three days go by and they call and claim Eureka! We've found the problem! Clogged catalytic converter causing air flow restrictions. They replace two converters and I go to pick up the truck. It runs like garbage. Further the sound is still there. Call Chevy, leave the truck and take their loaner back home. Next morning Ford's Foreman calls and basically tells me that there's nothing else wrong with my truck and that he even reprogrammed the PCM (which is why it runs to bad all the time now I guess) to get rid of the idle problems.
Long story short here's everything thats been done:
- Cleaned a clogged fuel filter
- Replaced fouled plugs
- Replaced the intake manifold and gaskets
- Replaced the fan belt
- Replaced the fan clutch
- Replaced the water pump
- Replaced two catalytic converters
- Cleaned the throttle body
- Bled the PS system
- Reprogrammed the PCM and transmission control module
After all of this I still have a hissing sound when I accelerate (video 1:
It seems the truck runs worse once its warmed up and even worse once the AC is turned on. I'm sure he programmed the PCM wrong and thats what is causing the truck to run rough.
Ford F-150 (2004-2008) :: Running Rough / Ticking Noise / Low Mileage?
the F150 of my brother has the follow diseases:rough running ticking noises, low mileage per gallone, blue smoke out of exhaust after start, i have ordered the cam phaser, hope, that will be the reason. But today, my brother means, i have to do a test drive, because the truck has no power. and really, feels like missing of one or two cylinders. Very bad performance. Is it possible, that the reason are the phasers?
View 4 RepliesFord F-150 (2004-2008) :: 2005 - Intermittent Rough Idle When Engine Is Hot
I just purchased my first F150, 4.6L V8, 55,600 Miles. It intermittently has a rough idle and only seems to be when the engine is hot. I've had engine and tranny mechanics look it. The spark plugs have been inspected and are within an acceptable range. The throttle body has been cleaned. There are no trouble codes of any kind. What I can check next?
View 13 RepliesFord Ranger / B-Series :: Runs Rough For About A Minute After Engine Started When Cold
This has been an ongoing issue for about a month. When I start the engine after it has been sitting and is cold it runs ruff for about a minute then smooths out and runs fine. I pulled a P0304 code (cyl.4 missfire) but I do not get a CEL.
I checked the plugs and they were ok but I changed them and the wires anyway as it just turned 50k and the plugs were original. I could live with a little cold ruff idle but the code throwing bothers me. The truck is a 2000 xlt 4x with auto trans. and 4.0 engine. This is my second 4.0 ranger but I have only had it for about 6 months.
Ford F-150 (2004-2008) :: Running Rough At Stoplight / Service Engine Light Came On
I just had my 04 5.4l engine rebuilt. Ive driven it about 500 mi and it started running rough at a stoplight. I tapped the accelerator and it started running good again but service engine light came on. I pulled the codes and they were P0022, PO345, P0340,and P0430. It has done this several times now. Everything was replaced including the phasers, except for the camshaft sensors. Could they cause this problem?
View 3 RepliesFord F-150 (2004-2008) :: Engine Will Run Really Rough And Knock Loudly In Reverse Or Park
I have a 2008 fx4 with 75000 km it runs great but when I go on a long ride up hills or tow my trailer it acts up only when I get to my destination. the engine will run really rough and knock loudly seems only when I use reverse or sometimes park (and oil pressure in dash looks good),and if I shut ignition off and restart it no problems till I make engine work hard again.
View 14 RepliesFord F-150 (2004-2008) :: Knocking Noise / Running Rough And Stalling - P0340 And P0345
I have a 2006 f150 it was making a knocking noise after the engine oil temp reached 160* and made the noise to 1700rpms. I thought it was the cam phasers so I replaced them. The truck is still making the noise and running rough and stalling but not as bad and not as often. Before it did it all of the time. The truck is timed properly. I had a new cam sensor and tried it but that did not work. I watched vct on the scan tool and both cams are in sycn.
View 2 Replies