I have a 2005 KR that the 4wd doesn't lock in the front wheels. I haven't seen my exact problem as I have been searching it. When I turn the switch. The dash lights both in high and low 4wd. I hear the transfer motor engage in both hi and low. No ratcheting noises from the wheels. I have replaced the solenoid. And still nothing. Checked fuses And they are OK.
View 3 RepliesI just recently bought a used 2004 fx4 with 148k and everything appears to be engaging but front wheels not pulling. I've already replaced the IWE solenoid behind the battery to avail, my question is, when I put it in 4H, light comes comes on, but I don't "feel" the transfer case engage, when I put it in 4L, light on I feel it shift. So could the shift motor not be engaging the front driveshaft even though the lights come on?
View 10 RepliesI have a 2006 XLT w/ the 5.4L engine. Manual transfer case, I'm wondering where to start looking for problems w/ the 4x4...the front wheels don't engage.
View 3 Replies2006 Lariat 4x4 Troubleshooting. My front wheels wont engage when I select 4H or 4L. No dash lights are ever lit.
I read up and understand how the system works and plan to replace the solenoid, transfer case motor and both hub actuators. I swapped out the solenoid and wanted to test that it was functioning properly so I followed the video below:
YouTube........
With the engine running and selector switch at 2WD, I pull the vacuum lines off and can feel vacuum at the supply. I then hook up just the supply line up (to the bottom port) and expect to feel vacuum at the other solenoid port (top port - what I would call the outlet) and cannot feel any vacuum.
This has halted my repair attempts as I am not convinced this is functioning and would pull in the actuators if they were functional. I know it's a small vacuum from a small orifice but I would think I should feel it by hand, no?
The solenoid's electrical connector is plugged in during this as well. I get the same performance with the old solenoid and the new. If I bypass the solenoid I can feel vacuum at the front wheel hubs.
Should I try a third solenoid? Seems unlikely I would have 2 bad ones...No OBDII codes at all. What to try next?
I have an intermittent grinding noise coming from what sounds like both front wheels, it sounds like metal on metal almost like something metal rubbing the rotor but I just put new pads on and the noise was there before as well with nothing touching the rotors but the pads. The sound will appear out of no-where at low speeds of 35 or below and will continue until I brake and slow down, just before I come to a compete stop the noise will stop with a slight clunk.
I can then drive away with no noise. I am pretty sure it is not brake related except maybe ABS somehow but was also thinking front axle or diff, also have read posts that are bearing related, but both at the same time?. It is the slight clunk before stopping that I can not figure out is related to. It is an 05 f150 xlt 5.4 super cab 4wd with 85k miles
Quick 4x4 always on... Is there a way to permanently lock the front wheels? My than ferry case works to engage the front axle. But the wheels are not engaging. I have put enough money in to it and would like to permanently lock the front wheels.
View 5 Replies(2004 f150 S.Crew 4x4) I noticed that my 4 wheel drive is not working. The front hubs won't lock in. The transfer case will go into 4 low but the hubs still won't lock in.
Anyway, I have pulled vacuum on both actuators and one of them won't hold. It's obviously bad, but is that why I don't have 4x4? It seems to me like it is not...
When I pull a vacuum on the actuator that does hold, it disengages the hub from the driveshaft allowing free-wheeling. Correct me if I'm wrong, but when the truck is running in 2wd, vacuum must flow to the actuators preventing the hubs from engaging? The actuator on the bad side is locked 'in' so the driveshaft always turns.
According to my train of thought, since the actuator has failed in the 'locked in' position, I should still have 4x4- What am I missing?
This is the first winter I'm driving my truck. I put it in in 4x4 HIGH the other night due to the snow (and I wanted to check out everything).
Seemed to work fine until I was backing into a parking spot doing a full lock turn. It didn't seem to move. I gave it a little more throttle and it "released" like it was stuck or going over an obstacle. Happened again when I did a full turn backing into my driveway (this time turning the opposite way).
It seems to work fine going forward with tight turns. Also and it doesn't "bind" in 4x2 mode. I haven't tried 4x4 LOW yet ... I guess I don't want to wreck anything if it's not operating properly. Is this normal?
My son has a 2003 Super Duty with auto locks, but the front wheels won't lock even when turn to locked position. Also when it's in two wheel drive the front drive shaft and axles still spin, are the hubs locked up or is it in the transfer case?
View 10 RepliesWeird issue started last night--I have an 08 and when you go to lock the doors the two front doors will not lock--you can see them jog a little but do not lock.. The back doors and rear lock fine. also I have them set to auto lock after you take off and again all lock but the front doors?
View 9 RepliesSo I'm new to the all time awd car thing. I came from a 4x4 truck which 4x4 was never engaged on pavement or in tight cornering. When maneuvering my is250 awd in tight spots ie. parking lots and the front wheels are at full lock in either forward or reverse there is a slight binding/grinding feeling or faint noise. Is this normal on an awd car or Lexus specific??? Did a quick search and didn't find much about this issue. I'm pretty sure its not tire rub.....stock set up.
View 10 RepliesProblem I'm having, when in overdrive my 04' F150 FX4 5.4 Triton surges while trying to maintain a steady speed during power delivery to the wheels, it causes a shuttering and bucking effect. If I push the button to turn the O/D off, the RPMs rise and problem goes away. During the problem no CEL illuminates and tach stays constant. Fluid condition & level are okay. (not burnt) I'm completely baffled since there is no code in the ECM to point me in the right direction. I do use the truck to occasionally tow my 5k lb boat & trailer. When I began towing I did not know to turn the O/D off and put some miles on towing in overdrive, I know now that was not good for the tranny.
View 7 RepliesAfter a transmission flush, my husband's Ford Ranger rear wheels have locked when backing out of the garage; pulling out of a parking spot; and driving down a hill.
He had checked the transmission fluid level, and it was a little high. The shop drained it down to where it should be, said the fluid was discolored, and sent him on his way. But it has happened again since then.
I drive an 06 Prius and it just started making this squeaking sound from the wheels when I steer. When I make turns you can hear the sound both ways when turning the wheel.
I took it to the dealership for the steering recall but they didn't seem to find anything. Is it just something I can lube up to make it go away or is it something more serious?
Ive got a 2006 5.4, Fx4, screw, with 90,000 miles.
Recently it shifts perfect except when it down shifts from 4th gear to 3rd gear. If i mash the pedal it is fine, its only when it just a slight acceleration and it is a easy down shift that causes the problem. What it does is almost like it wont lock into the gear, it bucks lightly but where I can feel it still. Im going 40 to 60 mph when this happens most of the time.
I am not sure if there is a sensor of something else that would be the cause this of is maybe my Transmission is just shooting craps. Also, i have a SCT tuner that i havent hooked up to the truck yet, but do you think if i plugged it in and turned up the shift firmness if it would work.
109K and runs great except for when accelerating from start to any speed. The front end acts likes the front wheels are slightly out of balance. Once you stop accelerating all is fine. Tires have plenty of tread and no I haven't rotated them to the rear which I might do?
View 1 RepliesWhen I turn the wheels to full lock, either right or left, I hear a clunking sound. Usually pulling into parking spots, into the driveway, etc.....but only going forward, not in reverse. Where do I start?
View 9 RepliesHow do I remove ignition lock cylinder to take and get new set up?
View 4 RepliesI can't get my shifter to move out of park. I took it in and they replaced the brake switch and although that seemed to fix it it started up again after a week of use. Now I'm stuck in my driveway. What's causing this?
View 13 RepliesI have a question about the front seats in the GTI/Golf. I'm looking to purchase a 2010 3-door Candy White DSG GTI, and am super pumped! The front seats, when slid forward to access the rear seats, don't lock in the forward position? It seems like they should, I know they lock in the forward position on a friends 2008 Golf. Neither seat locks, which makes me think that they don't and I didn't have the owners manual to check. With all the thoughtfulness of VW, I'm guessing that I'm missing something, or the seats are screwed.
View 1 RepliesWe have an 01 Sport Trac as a backup vehicle and it has the 3 position rotary switch on the dash for 4wd.
The transfer case engages and disengages but the front wheels seem to stay engaged with the front differential.
There are no manual hubs and I really don't think it should ALWAYS be engaged like that.
What is the probable issue and ALSO can manual hubs be installed on this truck?
Someone mentioned vacuum engagement? but I didn't see any vacuum hoses near the spindles. Didn't see any wires either other than ABS...