Ford F-150 (2004-2008) :: 2007 XLT Won't Start - Random Rough Idling Spell Or Stall Going Down The Road
Aug 29, 2013
I have a 2007 F150 XLT, Supercab 6.5' bed, 4x4 5.4 Automatic with 67000 miles on it. Its not a Flex Fuel
Over the past couple of weeks it would get go through random rough idling spell or stall going down the road. If it was sitting it would idle clear down to 200 RPM's and just sound like an old 'chitty-chitty-bang-bang' car, not a modern marvel of Ford engineering!
I noticed it particularly does it this on an incline. Initially I fixed it by just coasting to where it was flat. I normally keep it above half a tank so i dont think its a fuel pump not getting fed. So I replaced the fuel filter yesterday hoping it was full or clogged, no changed.
This morning it would start at all, I removed the negative terminal on the battery, rolled to the level, tried it 30 times. Nothing. I checked all of my connectors under the hood and the 2 below the cab under the plastic cover. Everything was connected. I disconnected the fuel pressure sensor and it fired right up and runs smoother than since I've owned it.
It hasn't had any CEL lights, until I disconnected that sensor. Should I drop the tank and clean it? Is there any special gasket kits or connectors I should be aware of? Should I just replace that sensor? Is it connected with a chain of sensors I should check first?
View 2 Replies
Advertisement
I have a 2007 F-150. Here is the story....
Last summer the truck was idling rough and seemed to be stumbling a bit. Took it to the dealership and had it diagnosed. Had a mis-fire code on cylinders 1 and 3. I was told to do the spark plugs and clean the MAF. After replacing all plugs and cleaning the MAF the truck seemed to run better but it didnt last long before it started doing the same thing. My Edge Evolution started showing misfire codes in cylinders 1 and 3 again and the truck is stumbling like crazy. Here is what i have done:
1. Swapped the plugs from cyl. 1 and 3 with cyl. 5 and 7 and the problem followed.
2. I replaced the bad plugs with new ones and i no longer get a code for those cylinders but the truck is still acting the same.
Now I am getting two codes saying the system is running rich on bank 1 and 2 and a misfire code in cylinder 4. I cleaned the K&N filter and replaced the MAF but it is still the same. The truck stumbles horribly under a load and has NO power.
History:
2007 F-150 5.4L Lariat
75K miles +/-
K&N Filter
Edge Evolution (has been kept in stock mode)
new spark plugs last summer
new MAF (this week)
New Fuel filter (two summers ago)
View 5 Replies
Let me describe this perplexing issue. I have a speratic rough idle problem. When it happens it's almost like the truck wants to stall. Once going the truck is fine. There has never been any acceleration issues, but for a short time the truck would kind of lunge off idle. It hasn't done that for quite some time. I've replaced the fuel filter. There are no vacuum leaks that I know of. I've tried higher octane fuel. I've tried injector cleaner for a month. What should the fuel pressure be and what is the test port located? Is the fuel pump in the tank? If so, whats that big log looking thing behind the gas tank that the fuel lines run to? Also, there are no MIL codes...
View 14 Replies
My 07 F-150 5.4 has a rough idle during a cold start for about 1 minute. It happens mostly when the weather is chilly or cold. Also after the first start it doesn't do it the rest of the day. Of coarse they can't find anything wrong and tell me there are no updates for anything like that.
View 3 Replies
I have 07 sscrew with 5.4. 93,000 miles. At start up truck runs perfect. After 20-30 minutes of running motor will start to start running rough at low rpm. Diesel sound. I can rev up and motor clears up and idles fine. Should I replace VCT solenoids? Or phasers? Or both at one time??
View 14 Replies
I have a 2007 Ford F-150 5.4l v8...
Codes
P0012 int cam position timing over ret bank 1
P0022 int cam position timing over ret bank 2
P0300 random Missfire detected
P0316 engine misfire detected on start up
P0340 cam position sensor curcuit fault
P0345 cmp sensor a circuit problem bank 2
Starts rough, idles rough and stalls occur often when start, after it runs for 5 minutes and sometimes dint starts at all. I replaced spark plugs, coils, cam shaft sensors and had oil changes done and. No effect.
View 8 Replies
My 04 F150 has started having a rough idle. While in park the engine will stall out with the A/C off. Also when in drive the truck will idle close to 1000rpm's. I had to the fuel filter cleaned and also the MAF sensor cleaned. Also did a vacuum check on it. Pulled the code and it's throwing a Lean Code. What else should I be looking for?
View 12 Replies
My truck is idling terribly and knocks while doing so, little info is
The truck has 170k miles, I just bought it about two months ago and it was running perfect, drove it to the beach two or three times (4 hour drive) no problems whatsoever. Two weeks ago I noticed it start rocking a bit at idle ONLY when warm, check engine light came on so I ran the code and it said the Cam shaft positioning sensor was bad so I replaced both of those, then the next code I got was for the vct solenoids, replaced both of those and the problem is still persisting. It is odd to me in the fact that when its cold, it runs flawlessly, no problem accelerating/idling/maintaining speed/smoke nothing at all.
As soon as it gets warm it will still do everything flawlessly EXCEPT idle. the idle rpm is around 300-400 and it rocks and knocks terribly.. If i am stopped and I apply some throttle in park or nuetral, just enough to get the rpm up to around 800-900, its perfectly fine. no more rocking no more knocking but as soon as i let my foot off the gas it goes right back to feeling like its going to fly out from underneath the hood.
So my question is why is this? What on earth is going on here? and how do I fix it? And why is there not a manual idle control. Ford place said there was likely damage to the head and recommended a full engine replacement.
View 2 Replies
I have a 2007 F150 It will stall out when I go over a speed bump. It has happened several times and getting worse. No codes stored. It will also skip between 40 and 50 mph.
View 3 Replies
Have an 06 F150 5.4 3v with no power. spark knock. rough idle. wants to die while driving, and random misfire code. Have replaced fuel pump, filter, coils and plugs. What to check next? Already thought of EGR - it doesn't have one.
View 4 Replies
I have a 2005 5.4 F-150. First off it came to me on a rollback because the owner tried to replace his plugs after he noticed it missing and of course broke one off. So after I extracted the plug from #8 cylinder and installed a new plug I cranked the truck and it was idling very rough and had a terrible miss around 1200rpm. I pulled the codes and got several misfire codes and ignition coil faults on #5,6 and 7 cylinder. Popped in 3 known good coils in these 3 cylinders with no difference.
On Mode 6 on my diagnostic software you could watch the misfire count steadily increase on #7 and every now and then there would be a single misfire on #5 and 6. It also had several codes for O2 sensors biased, stuck rich on that bank. Well since it had a brand new plug and coil, I popped an injector in #7 and havent had a single misfire on it since and it also started idling alot better and all the O2 codes went away. The problem I am having now is #5, 6 and now 8 will randomly misfire, sometimes build up a steady count on one of them, sometimes just skip around between them.
The truck has brand new plugs in all 8 and new coils on this bank also. The truck has 115,000 on it and does have some cam phaser noise on the bank causing the problem, but its not too terribly bad, I have heard alot worse. My problem is something on that bank only as the passenger side bank is fine. I am wanting to say cam phaser now since this is the side with the noise. I have changed them before but have just experienced the noise, never one running like this because of it. Possibly jumped time a little?
View 14 Replies
I have a cylinder 3 misfire and the vehicle is idling rough so I took it to the deal because I have a power terrain warranty. They're telling me I'll need a new manifold and plenum, coil pack, plugs, and gasket. Could this be accurate? I don't want to get screwed over...
View 9 Replies
My brother's 5.4 has been rough idling and dying at stops and in reverse for a few weeks now. Today it threw a code and he finally had me look at it and it's a P0345 code. I was thinking cam phasers possibly, but I didn't think that would cause a code to throw. Also, all I hear about cam phasers is that it makes the truck sound like a diesel, but his when it's about to die sounds like the engine is about to drop out the bottom of the engine bay. Really rough, REALLY loud knocking, etc... What we should be looking at replacing to get this thing back into shape?
View 3 Replies
I have a 6.0L Powerstroke with about 74k miles. I've owned it about a year. this weekend while driving on the highway at about 55mph i slowed to make a turn. As it came to idle i noticed it was idling real rough. As I accelerated it barely got across the highway. I went to where i was going and let it idle but gave it gas and raised the rpm's to about 1k.
I was concerned it was going to die. As I left it seemed to be better but as i drove it would get real rough and then go away. I accelerated a couple of times engaging the boost and it seemed to be better. I made it home and parked it, but i let it idle before i turned it off.
Now it will not start. it just cranks. everything is pretty much stock. i replaced the fuel filters back in december and also did the blue spring upgrade. I have a OBDII but i didn't have it with me so i wasn't monitoring at the this time. What should be my next step?
View 14 Replies
2007 f150 5.4 supercrew, average temp for the last 2 weeks was -27. I plug the truck in all night it starts good and idles down fast engine is warm. no heat after idling for 3-5 min and then try to drive it takes another 5 min for the temp gauge to hit full temp 192. then my windows fog over even the dash and there is minimal heat coming out takes another 10-15 min to clear the windows. what the "F". fulid levels up, winter front on, block heater works, not using or smelling antifreeze, brush off every last speck of snow and I still have to pull over on the highway and wait......should have kept my 95 5.8l.
View 10 Replies
I have a 2006 Ford Expedition with 95,000 miles that has a crank but intermittent no start problem. When it does happen, it will eventually start after one to two tries. I don't have to wait to start it again and I don't have any problems while it is running. Two or three times in the past two months it will sputter out and die (even though I am pressing the gas pedal) right after starting. I'll crank it again and it starts just fine. I have no problems while driving at freeway speeds or around town.
I never had any check engine lights come on so I replaced the battery and the fuel filter. I finally got two codes and replaced the fuel pump driver module and the fuel rail pressure sensor. The codes went off after replacing these two parts. I can hear my fuel pump turn on every time I start the vehicle. I have even taken the entire fuse panel apart to check Relay 303 which is soldered into the circuit board. It is fine and so is every other fuse in the panel.
View 3 Replies
I love my '86 Mustang GT convertible. Currently at 106,000 miles and running strong. The problem is searching at idle. I have replaced every sensor that me and my mechanic can think of. New plugs and wires along with rotor and distributor cap. The engine will start searching, i.e. idling up and down, and at time stall. If I apply slight pressure and idle up to 1,000 RPM the searching stops. Hard to do sometimes as this is a stick.
View 4 Replies
I changed timing belt and water pump DIY back in Oct 2015. Ever since then, I get rough idling (car kind of vibrate and engine kind of struggling) after warm start (no problem with cold starts, it did stall once after the warm start).
Two days ago, I got a P0000 code, I thought it was due to low oil (happened before, I topped off oil 2500 miles ago), so I changed oil and filter. No problem yesterday, but today on my way to work. I got the p0000 code again.
View 17 Replies
The 93 Cutlass Ciera 3.3 6 cyl. is hard to start..takes like 3 tries to start it...even after changing..oxygen sensor, MAF sensor, coil pack, fuel filter, air filter, good plug wires, crank position sensor, fuel pump, sending unit....if idling low will stall sometimes. Mechanic said it's slow getting spark up just when starting it..not sure why..
View 1 Replies
I have 2004 chrysler sebring and lately when I'm at a light/stop sign the rpm gauge fluctuates between 1000 and 500 and wants to stall. I've been told to change the spark plugs and wires, cleaned the throttle body, and put in a new air filter. What else I should do?
View 1 Replies
The Accent is a 2004 and it belonged to my parents. It is a 5 speed manual trans. and has about 100K. It runs fine except when stopped and idling it stalls. It starts right up again, but stalls every time it idles. My dad said it was something inexpensive to fix, however he could not remember what the part was.
View 3 Replies
