Ford F-150 (2004-2008) :: 2007 - Vibration And Noise At Highway Speeds
Aug 11, 2017
First, details about my truck. 2007 F150 SuperCrew, 2wd, 5.4, 203,xxx miles on it, leveled with Hell Bent Steel 2.5" kit last year, has been aligned professionally since then, tires are good and balanced.
The issue I have is a vibration, kind of the same feeling when driving on a road surface that has had the top level of asphalt removed before it's resurfaced. It's mostly noticable at highway speeds. Its not a violent type vibration, but you can feel it. There is also a sound, similar to tires with a deep off road type tread.
The sound and vibration more noticeable when making lane changes or when wheel turned towards left, at highway speeds, not as much to the right. I've checked front wheel bearings, they are good, zero play, no loose suspension parts, u-joints are good, no leaks anywhere.
Since it makes the noise and vibration a bit more when moving wheel, could it be a power steering pump? The pump is the original.
View 1 Replies
Advertisement
I have a 2007 F150 King Ranch Super Crew 5.4 3v and it makes a ticking sound. I have read about the VCT solenoids and the phasers. My issue is that the ticking noise can be heard at Highway speeds. At it seems to be quicker as the engine speed increase. Not sure what to think. No rough idle. What could this be.
View 3 Replies
I have a 2007 F150 (2wd) with 80k. My truck recently was vibrating under braking so i took it to my mechanic to have the brakes fixed. All the rotors needed to be replaced. In doing so, the front rotors were changed out with the kit that converts the front rotor/bearing assembly into two separate pieces to cut down on maintenance costs in the future. With this being said, after getting this work done, the truck didn't vibrate anymore... that is until i got it out on the highway. Now the truck vibrates from about 45-50 and 70-80 pretty bad. The steering wheel shakes back and forth too. I have gotten the tires balanced in hopes to fix this problem which it didnt. What could this problem be?
View 4 Replies
On my 07' I bought it home mid AUG. It has been getting much worse to a point there is a rear driveline vibration at all speeds above 40 and up to 70. I used to change intensity whether you are on or off the gas, and would almost vanish if in neutral. However now it is all the time.
I cannot feel any play on the u-joints, the yoke has a little play in the xfer case but is is normal like on most other trucks I have owned, and the pinion flange is nice and tight. Could this be **tight** ujoints or the driveshaft itself? It looks rusty, but there are no dents on it.
View 4 Replies
I'm having an issue with my wife's 2008 Camry. We're feeling vibration at highway speeds. Feels like it's coming from the front passenger side. We've had all 4 tires replaced (two of them replaced twice because we got lucky and the shop gave us a set of 4 for free with all the trouble we were having with the goodyear tires they sold us), and added hub-centric rings to her wheels. There are no noises to tell me whether it's a cv axle or a bearing. I've been under the car and the only thing I can find that comes close to loose is that the passenger side axle has a just a little more side to side play (runout - inner cv) than the driver's side.
View 11 Replies
Owned my 2009 for 6 months now. Ever since purchasing it, car will vibrate significantly at highway speeds when first driving it, then decrease by 90% after a few miles. At first, since I purchased in winter, thought it was cold flat spots on tires. Dealer changed tires 3 times, finally with a new set of Turanza OEM tires. Still does it.
Service manager said he drove new 460's and they all do the same thing for a few miles. I have seen other comments on internet from other owners who report the same phenomenon. Don't think it is the tires since we went through 3 sets and it still does it in the summer. What else could cause a vibration until the car is warmed up?
View 14 Replies
I replaced my tires yesterday with Bridgestone Turanza ER33 (245/45/19).
After replacing the tires, there is is an extreme vibration in the front end of the car when braking at highway speeds (60+ mph). Braking at sub 50mph speeds is completely normal. No lights, no vibration while driving. What could be the reason?
Also while removing the lug nut locks, the locks key broke apart (the black piece came out of the key). After like 45mins of trying, finally we got the locks out. I threw them away.
I searched online for regular lug nuts, but couldn't find any beside ebay. The local dealer says I need to wait for 3 weeks to get them from Japan! Where can I get a set of 4 regular lug nuts online?
I'm now running on 4 lug nuts on each wheel. Could this cause a problem? Could the vibration be caused by not having a 5th lug nut in place?
View 14 Replies
Since day one my 2016 F250 occasionally has a reed sounding vibration at highways speeds near the passenger side occupant handle on the windshield pillar. Talked to a service advisor at the dealer about it, what it could be, so this must not be a common problem . The issue is intermittent and can not be reproduced on demand. I tried blowing compressed air all around the area of the Windshield to see if I could reproduce the sound in a shop setting, but no luck. Only thing in common with this noise is 75+ MPH during a rather windy day. I'm a little reluctant to drop it off at the dealer since intermittent problems are hard to diagnose.
YouTube...
View 10 Replies
I've been doing a lot of decently long highway trips this summer (5 hrs @ 75-80 MPH) and I've noticed that the 2008 VR6 Passat has some kind of pressure/wind noise/vibration above 75 MPH. It's hard to describe; it's like the noise you get when you open your sunroof too far and you get a harmonic noise from it. The sound seems to be coming from the upper rear of the car; behind the sunroof and almost from the rear glass.
All of the windows are up, the sunroof is closed and even the shade is closed to muffle the noise, yet it is there. However sometimes it isn't bad. If I have the radio on I don't notice it really, but when it is off it is very noticeable on certain stretches of highway. I'm having a hard time nailing it down as it is not entirely reproduceable. I don't know if it has to do with temperature, angle of the wind, climate control fan settings, what.
I did notice a few reviewers of the new CC complaining of a similar thing, which freaks me out that it is a design flaw - yet searching on here brings me up empty so I think it might be something I can fix. My first thought is that I have a tire slightly out of balance, yet the noise seems more wind related than tires.
View 10 Replies
06' 5.4 screw 100K... At 55mph my truck just stopped running, I pulled over to the side of the road and after two trys the truck restarted but ran rough. Auto Zone pulled a code that said replace the throttle position sensor, I did and the same thing happened again two weeks later just as before.
View 3 Replies
This has been happening for the past 6 months or so. I recently had new ball joints, 4 wheel alignment, and 4 wheel balance. Even with this I'm noticing a very slight high frequency vibration at highway speeds. I noticed on one of the front wheels that a weight fell off, so this might explain the high speed vibration.
However - When I'm starting at 0mph, and accelerate to say 50mph for example, the car vibrates rather substantially as the speedometer moves from around 25mph to just past 30mph. After those speeds it goes away.
I've also noticed that it tends to be worse if I'm going up hill, which, according to the laws of physics, would tell me that going uphill would put more pressure on the front end, given it's heavier with the engine there. If I'm going downhill it vibrates much less.
When I drive I tend to not accelerate quickly, meaning, I don't 'punch' it, and accelerate gradually instead. If I'm driving on a level, well-paved road, and accelerate quicker than regular, the vibration seems to not be as heavy.
Any other tests for this? Struts, control arm, steering knuckle, drive shaft ?
View 14 Replies
5.4L... My truck has a momentary moan / growl / bog down issue. It happens at town and highway speeds and usually when I have cruise on OR when I lightly apply the gas peddle. It moans for a few seconds and seems to bog down then comes out of it and carry's on its way. You can hear it plainly while driving even with radio on. I have a regular muffler on the truck but when this happens, it makes it sound like I have a catback on it.
Things i have done...
- New air filter
- New oil/filter
- New fuel filter
- Ran techron injector cleaner through tank of gas
View 6 Replies
I have an '05 F150 5.4L with 110k miles on it. Bought it used about 2-3 years ago and have had on-going ignition system problems. The current problem is a significant shudder/shake/vibration that occurs when driving 50mph+ (easy to reproduce around 65-70) on the freeway, when starting up a minor, but noticeable incline. This is an incline that doesn't require much additional throttle, and this trouble occurs with cruise control on and off. the truck starts shuddering pretty rough during the incline. However, if I release the accelerator (and go up incline with slightly lower speed) or give lots of gas on accelerator the shudder usually stops. The shudder always clears after the incline when returning to flat road and just cruising.
This occurred on a recent trip a few times and I pulled the following codes (in order):
P0356 (once) : Ignition Coil F (6) Primary/Secondary Circuit Malfunction
P0302 (recurring): misfire on cylinder 2
I have since purchased and replaced the coil on #2. This did not resolve the problem. I have replaced coil on #6 in the last year...
Because I saw a suggestion somewhere on the net around this problem while searching, that this could be related to OD, I tried disabling OD and enabled OD on an incline today to test after replacing COP on #2 and it seemed to resolve the issue to turn OD off. Not sure if related...?
Other observation: Cab of truck often smells of gas just after starting the truck. Mentioned this to the shop, but they didn't find anything obvious.
Short history of codes and work that has been done:
Sometime in early 2011: Ford service dept did this work.
First failure was coil bad on #7. Tech swapped 7 & 8 to verify the problem followed the coil. Then when the problem DID follow the coil, he replaced #8 with new.
05/2011 MacKenzie Ford changed all plugs
12/2011 - swapped out COP on #7.
02/2012 - P0306 - Now, COP #6 is reported as bad.
November/December 2012
P2104 P Throttle Actuator Control (TAC) - Forced Idle
P2112 P TAC Stuck Close
P2111 TAC Stuck Open
I did throttle body clean - removed it and used TB cleaner. replaced...
Late December 2012 - while driving on freeway at speeds 50+, but easily reproduced around 60 after starting up a slight incline. symptom is heavy shudder/shake. Possibly resolved by turning OD off.
P0356 (once) : Ignition Coil F (6) Primary/Secondary Circuit Malfunction
P0302 (recurring) : Misfire on cylinder 2
View 3 Replies
2006' screw, 5.4L, 116K miles ... The truck looses power at highway speeds to the point that I need to pull off of the road. When this happens the check engine light is on and the truck is still running but will not accelerate, is it possible the computer is going into limp mode and if so what would cause this?
View 1 Replies
I recently had u joints and left front wheel hub assembly replaced at a local mechanic. Ever since I have a vibration between 40-45 and 52-62, the vibration can be felt in the steering wheel, the seat and the floor. The mechanic claims I need a new driveshaft as some of the counter weights were starting to rust. I indexed and removed the drive shaft and had it rebalanced at a local machine shop. This did not solve the vibration problem. There is also a transmission leak starting from the extension housing. How I can start to trouble shoot the problem. 04 F150..
View 2 Replies
I have had a 2004 Extended Cab F150 5.4L for a few months now. It just started vibrating at speeds between 15 and 30mph on accelerating or deceleration. Doesn't matter if I'm turning or going straight, just those speeds. It's fine otherwise. I put it in gear and held the brake down and brought the rpms up to 3000 to see if it would shake with a load, thinking a possible misfire, but nothing abnormal.
It's an automatic transmission. I started off in 1 and 2 and it seems to lack power until it shifts to 3rd gear - which is about 30mph. It also seems to lack power in reverse ... no slipping, but seems to have to give a lot of gas in order to go over the slightest incline backing up.
View 1 Replies
Trying TSB 05-13-1 on f150 ? Mine is a 2004 xlt 4x4 and it shakes and vib really bad from 55 to 60 mph ,had tires balanced 3 different times brakes replaced and rotors turned ...
View 14 Replies
So my 07 with 125k miles has had new rotors for about 50k miles or so, but for a while now when the brakes get hot it gets a violent shudder on braking at highway speeds....the odd part to me is nothing at lower speeds, and not always at higher speeds....do I just have warped rotors again? The rest of the front end I good and tight....
View 9 Replies
Today I caught a deal on a 06 F-150 with the 5.4l. I noticed a slight vibration that comes and goes at highway speed (65-75), when I got home I jacked the front end up and checked everything out. The right front CV axle is still engaged with the tire when it is out of 4 wheel drive, I can engage the 4wd and everything locks in and works as it should. My understanding is that the axle should spin free and independent of the wheels when in 2wd? How would I go about troubleshooting this?
View 4 Replies
I'll try to keep this brief. I bought a 2008 Sante Fe AWD 7 passenger 1st week of Sept 2008 from Jim Pattison Hyundai in Nanaimo BC. Vehicle had a pronounced vibration at various speeds but was most noticeable at around 85 kph which seemed to vibrate frame, not steering. I called service department at the dealership. They said they would look at it during the trailer hitch install in 2 weeks.
After dropping off vehicle for trailer hitch installation I mentioned problem again. Later that day I picked up vehicle and asked about vibration. I was told "mechanic didn't feel anything". Got service manager to take a ride with me, vibration now felt by service manager.
View 29 Replies
I have a 2010 Santa Fe AWD, I notice that when I apply the brakes at 100 KM or higher I hear a 'thumping' noise, the noise is hard to describe, thumping is the best I could come up with, the noise goes away once the vehicle is down to 80 KM, why this is?
View 7 Replies
