Ford F-150 (2004-2008) :: 2007 - Stumbling And Hesitating A Bit Between 25 - 35 MPH / P0307 Error Code
Dec 31, 2013
My 2007 Ford F150 Lariat (5.4L) with 82k miles popped a P0307 (#7 misfire) code one chilly morning. It began stumbing and hesitating a bit between 25-35mph, and each time it occurred, the engine light would flash on and off. Hesitation clears and light goes steady. Cleared the code and didn't see problems again for a month...until the next cold day (freezing temps). Popped again and hesitation returned. Ford dealer wants to change plugs. I've read coils can also cause the issue. Not sure if I can do either myself.
View 4 Replies
Advertisement
We bought it in 2010, since then we have replaced 5 ignition coils and 2-3 batteries. Everytime the car acts up, the VSC and traction lights come on and the car starts stumbling and hesitating. The car eventually dies within a few minutes. Pull up codes and its always been an ignition coil.
Well we had all of these covered under warranty until the warranty expired in Aug. A month ago this happened again, and thought the battery was dead. It ended up being #4 coil, so I replaced.
My wife drove last week and lights came on and lights started going on/off and dinging at her and the car died. I jumped it to get it home, turned off the car and was dead. Voltage at battery was 9 volts.
I charged overnight and started the next day. I pulled negative battery cable w car running to check alternator and it stayed running, so that's good. The car is now starting just fine again.....until this happens again.....which it will.
My question is what in the heck can be making all of the coils go bad and why is the car intermittently throwing warning lights and just dying? This last time the codes pulled we P0345, PO365, PO390. All of which I don't see an explanation for.
View 5 Replies
I have a 2007 F-150. Here is the story....
Last summer the truck was idling rough and seemed to be stumbling a bit. Took it to the dealership and had it diagnosed. Had a mis-fire code on cylinders 1 and 3. I was told to do the spark plugs and clean the MAF. After replacing all plugs and cleaning the MAF the truck seemed to run better but it didnt last long before it started doing the same thing. My Edge Evolution started showing misfire codes in cylinders 1 and 3 again and the truck is stumbling like crazy. Here is what i have done:
1. Swapped the plugs from cyl. 1 and 3 with cyl. 5 and 7 and the problem followed.
2. I replaced the bad plugs with new ones and i no longer get a code for those cylinders but the truck is still acting the same.
Now I am getting two codes saying the system is running rich on bank 1 and 2 and a misfire code in cylinder 4. I cleaned the K&N filter and replaced the MAF but it is still the same. The truck stumbles horribly under a load and has NO power.
History:
2007 F-150 5.4L Lariat
75K miles +/-
K&N Filter
Edge Evolution (has been kept in stock mode)
new spark plugs last summer
new MAF (this week)
New Fuel filter (two summers ago)
View 5 Replies
I just bought a F150 with 103,000 on it. The engine is a 4.6. I get a P0605 code every now and then which doesnt effect performance. I erase the code and it doesnt appear again for maybe another 100 miles.
I suspect a loose connector but not sure. Looked up the code and it reads PCM READ ONLY MEMORY (ROM) ERROR. My question is what does the PCM operate? And wheres a good place to start troubleshooting?
View 7 Replies
I have the error code P0340 and have changed both camshaft positioner sensors, cleaned the air sensor and throttle body and still the engine stalls. I can accelerate at 40, 50, 60mph and it jerks violently. I tried the "locking it in third" trick but it still jerks. Today I unplugged the left cam sensor and the truck idles @ 400rpms, does not stall, and pretty much drives great! Hook it back up and crank it, within 10-15 seconds it stalls. I plan to check the wiring....
View 14 Replies
I have two codes off my "digi moto lite" obd2 scanner....
P0201 - internet search suggests it's a fuel injection code....
However I can't find anything on code C3203....
View 8 Replies
I recently changed from a problem-ridden SCT Livewire to a SCT Xcalibarator3, and now when running my custom tune I get a check engine light and a error code P0605. I never got this on the same tune with the Livewire. What causes this and how to fix it?
View 4 Replies
What would make the OBD II not read the code that is set on my truck. It says "Communication Error..." Fuse 41 grants power to the Diagnostics port and the cigarette lighter. The cigarette lighter is working. Any other reasons I can look at?
View 3 Replies
I got the Check Engine/VSC/Triangle of Death errors yesterday. Autozone reports it is P0A80 (replace Hybrid battery) though no additional details reported.
I'm the original owner, and after some reading suspect it could be something else because:
1. In 8 years, the starter battery has never been replaced.
2. For about two months, the throttle has been hesitating when first accelerating (within first five minutes of turning it on). Yes, it is the hot summer months (though mild compared to previous summers). And the hesitation occurs even in the morning before things really heat up. This is definitely even worse after the error lights came on.
I've seen recommendations to replace the starter battery first. And other recommendations for "throttle body cleaning." I'm not a mechanic, but obviously would hate to have the hybrid pack replaced if it is something else.
I got the Check Engine/VSC/Triangle of Death errors yesterday. Autozone reports it is P0A80 (replace Hybrid battery) though no additional details reported.
I'm the original owner, and after some reading suspect it could be something else because:
1. In 8 years, the starter battery has never been replaced.
2. For about two months, the throttle has been hesitating when first accelerating (within first five minutes of turning it on). Yes, it is the hot summer months (though mild compared to previous summers). And the hesitation occurs even in the morning before things really heat up. This is definitely even worse after the error lights came on.
I've seen recommendations to replace the starter battery first. And other recommendations for "throttle body cleaning." I'm not a mechanic, but obviously would hate to have the hybrid pack replaced if it is something else.
View 11 Replies
Fault code : P1586 MT/AT codification, no check engine light, the glow light is blinking when I give ignition but if I turn off and turn the ignition on again the light it will go off. What I noticed is between 1500rpm and 2000rpm the engine is hesitating, like not getting enough fuel.
View 8 Replies
I have a 2001 King Ranch F150, which has a 2004 Lincoln Navigator 5.4 DOHC Intech engine installed. The engine was installed in 2005 and had less that 100 miles on it. The engine now has approximately 95000 miles and I have recently gotten a P0307 fault-miss fire on # 7 cylinder. I have installed a new spark plug, COP, and fuel injector. The fault has returned. What is the cause of my problem?
View 1 Replies
I got a Ford f150 and getting the error code P0446 Evaporative Emission Control System Vent Control. My truck has burnt up 3 of these things already in the last 8 months. Why my truck keeps killing them?
View 2 Replies
Got an 07 Screw with only 50,000 miles. Yesterday, wife drove it home from work and said it would only do 45mph and didn't sound good. No warning lights were on, she said. I test drove it in the evening and it ran totally fine. Today, she drives it to work and said it ran real rough and "Check Engine" light was on. I picked it up from her work and it idles very rough and slow, and once you hit about 2000 rpm, it runs decent, maybe even normal. Below that, it stumbles and engine doesn't sound right. "Check Engine" light is either ON steady, or flashing. I don't have a code reader, so its likely going to the Ford Dealer Monday. Is there any way to read the code without a reader?
View 11 Replies
How to reset and remove the error code on the tire pressure monitoring system?
View 5 Replies
I had a 05 f350 5.4 3v come into my shop with a CEL. Did the usual it had a p0307. So I did the usual again changed plug and coil plug cam out no prob they were done 15k ago. Test drove a few times and it was fine. Few days later customer brought back with same code p0307. thought maybe I got a bad plug or coil so I moved them to #6, misfire stays on #7. When I drive it local its fine when I go to pull on to highway and really put my foot in it CEL flashes (misfire) and it pings like crazy and loses all power. Scan it back at shop and still only p0307!!
View 10 Replies
I know there is a tun of info on the spark plug problem on the f-150. Here is the problem I have and I don't know where else to look.
Cylinder #3 misfires
1. swapped coil with #2 cylinder and still throws #3 misfire code.
2. Changed the plug on #3 and still the same code #3 misfire.
Where to look next?
View 13 Replies
I have a 2007 ford f150 and the 4wd will not engage at all checked vacuum lines they all look intact wondering if it could be the IWE solenoid and is there any way to test the IWE solenoid ...
View 5 Replies
99 F250LD 4x4 w/5.4 and 215k . I'm sure I'm not the only one with this problem. Just had quite a bit of rain in my area. I didn't drive the truck in it but 3 days after the rain stopped I did. Skipping badly ! It has done it before and will clear itself up after a heat cycle or two. This time it kicked a p0307 code. # 7 cylinder not fire correctly I believe. I got ready to replace the cop but decided to wait a day. In the mean time I pulled the connector and blue compressed air through it and the male connector.
The next morning I decided to drive it before replacing the coil. Absolutely no skipping at all. Drove at different speeds , up heels slow , high speeds, no skipping. Ran the truck for about 20 minutes or so. Is the connector getting moisture in it ? Can I fill the connector with dielectric grease? Is there another problem. I cleared the codes and am going to drive a couple of cycles to see if any come back. Like I said it has done this before but not bad enough to throw a code so I'm not sure if it's always number 7.
View 5 Replies
I'm having an issue with my 2003 Silverado, current engine is LS1 from a WS6 Trans Am, mostly stock, stainless headers, no cats, stall converter. I replaced fuel pump a few weeks ago and last week i took a road trip and when I hit the interstate the CEL started flashing. I pulled over and used my scanner and saw that it was P0307. I cleared code and continued on. The only noticeable problem was that it was not shifting into overdrive. After a while the light quit flashing and eventually it shifted into OD.
This happened several more times on a 750 mile trip. I had a mechanic friend check it over and he couldn't find anything, wasn't throwing codes at that time. He check sparked plug, swapped the coil to #5 and still had the issue. Didn't get a chance to check the fuel injector. The trip home it did the same thing. IF it were indeed a bad injector, wouldn't the problem be ongoing instead of coming and going? Took to local chevy dealer thinking they could diagnose it but since it didn't throw a code they couldn't find anything.
View 5 Replies
I am preparing to combat the old P0401, Insufficient flow issue. While looking at the steps in Alldatadiy the very first decision essentially forks on "EGR System Module" or "Others".
I am just guessing that, since the choice is there, some engines will have one and some will have the other. But I thought I'd come here and see if I could learn a little more about it.
How can I tell what my truck has? I'm sure there is some difference...
View 1 Replies
I have a 2008 Sports Trac, with a 4.0 SOHC engine ... 165k miles. Last week my check engine (CE) light came on and the code is P0401 ... too little flow on the EGR system. I first tried cleaning the existing valve - but CE light still came on. So I replaced the old EGR valve, cleaned the SS tube from the exhaust manifold back to the EGR valve and the CE light is still on. I have not driven the truck since I replaced with the new valve ... only fired her up in the garage. Is this something that could possibly clear up given a couple of miles?
View 6 Replies
