I have recently been having violent shaking when I make a turn to pull into a parking spot or turn at a stop sign. I can park my truck and the truck continues to shake until I turn the motor off. When I restart the truck it runs fine. It doesn't do this all the time just sometimes. I have a 2006 Ford F-150 lariat 2 wheel drive.
View 3 Replies2007 Ford F150
XLT 5.4L Supercab
55,500 miles
Only Owner
I have owned my truck since mile 1 and have not had any issues up to this point. That being said in 2011 there have been 5 occassions where I have been on interstate driving between 55-70 and had to pull over due to my truck shaking. This shaking is very extreme and truly scares me, thus the reason I pull over. I replaced my tires with Michelin 70,000 mile tires and also replace my front brakes just over a year ago.
After not being able to reproduce the shake for my mechanic, they said my upper front ball joint needed replaced and my rear shocks. They hooked the truck up to the computer and did not receive any codes and my check engine light has not come on to this point.
The research I have conducted to this point has pointed to a number of issues and I had my mechanic check all of them and they said nothing was out of the ordinary, these were: e-brake issues, front brakes, calipers, plugs/coils.
I have a 2008 Ford Focus with 122k miles in good condition, nothing ever replaced except an engine mount, shocks, and coolant thermostat and all regular maintenance.
In the last four months I have had a few instances of the car shaking during my commute. Only happens when I am either stopped at an exit ramp or stopped during heavy traffic on the highway. It can happen anywhere from 10-30 minutes into my commute. Feels like either the road is shaking from an earthquake or godzilla is standing behind it and pushing it back and forth. It's very strong but very smooth and slow. Like being on a boat. There is no vibration in the steering wheel or any other parts and no noise associated with it. It goes away once I start driving again.
I had a cracked engine mount once that produced a lot of vibration and rattling, and this shaking doesn't feel or sound anything remotely like that one, so I am doubtful that it has the do with the mounts (just had that one replaced a couple months ago anyway).
This is also extremely intermittent. Maybe once a month at most, although the time span in between occurrences seems to be shorter so that's why I am investigating. And when it happens, it's just once during my entire drive and then not again for another few weeks or so. So it would be hard to take it into a mechanic to reproduce.
What could this be? I've been thinking about getting a new car and this has me worried that I'm entering into the timeframe with this one where major things start breaking.
I have one 2004 Hyundai Elantra. It was parked outside for almost a year without being used. I recently installed a new battery and had the front brakes/rotors replaced - they were rusted on so tight the guy had to partly saw them off. So now that I have set the scene, why this car turns off in sharp turns. Luckily this only happened twice as i was driving slowly and turning into my driveway. I can turn the ignition and it goes right back on.
View 3 RepliesI have a 2006 F-150, V6, automatic transmission, a little over 214,000 miles. When I started it up this morning, no issues, but when I dropped it into reverse, it started shaking pretty bad. Got on the road and put it in drive, and the shaking continued, then the check engine light started flashing. Haven't had any problems up to this point. Checked all the fluids including the transmission fluid a few weeks ago and all was well.
View 4 RepliesI have a 2006 F150 5.4 3v rattling and shaking excessively. I have installed two new cam phasers, two vct solinoids, two vct housings, flushed oil and installed motor craft oil and filter. This never happens if bank two vct is unplugged or in open loop. Monitioring vct's on ids only bank two is erratic. Also when I had vct housing off I blew regulated air through oil passage seems free.
View 7 RepliesAfter my 2006 Ford F150 Lariet started shaking and pulsating when braking (38,000 miles) I took the truck to the Ford dealer and asked to have my brake pads checked. They came back and siad they looked fine and I had alot of wear left. Then I mentioned that is was shaking and asked them to check it again, they drove it and then said my rotors are warped and I need to replace the rotors and pads. I don't haul, tow or do anything crazy with it.
Now, here's my questions:
1. Can the rotors go bad and the brake pads be fine?
2. Should I go with a ceramic pad or stick with the OEM?
I'm just a female and don't want to be taken advantage of at the dealers. Cost is not an issue when purchasing a good product.
Ok, I have a 2006 Ford f-150 5.4L engine. it has 88000 miles on it. Here recently it has started acting up on me. It starts shaking violently when I slightly accelerate going up hills at any speed. On level ground it doesn't do it. Going down hill it doesn't do it. When stopped it doesn't idle rough.
It does this shaking when I barely press the gas. When it starts I either let off the gas or I push the gas to the floor and it stops. What is going on? This is the first Ford I have ever known. I don't know anything about these vehicles. I have read it might be the coils and plugs but then people have told me it might be the torque converter.
I've had this truck since 2011. Ran great when I got it. Ive had problems with the calipers and I've replaced both the fronts. I keep up on changing the oil regularly. The manifolds started rusting away a little over a year ago. Not happening... The shaking started recently after I pulled a trailer with 2.5 tons of shingles on 2 separate occasions.
That being said, I can feel a little shaking while idling. It was really only bad between 500 and 2000rpms. After 2000 it almost felt like a turbo and it would accelerate really fast and smooth until the gears switched. I figured i should change the oil. Now the shaking is more violent.
Its a 2000 f150 5.4 v8....
I have a 98 Ford Explorer Sport V6 with a 5-speed and 4wd (mechanically Identical to the Ranger) and I've been having a problem ever since the new clutch was put in.
The previous clutch cracked in some way and took the pressure plates with it, so it has an all new clutch and plates, installed by a friend who has a shop. Ever since getting the new hardware, I get a violent vibration when letting out the clutch in First or Reverse from a stop. Friend says it's probably the flywheel, and that fixing it is more trouble than it's worth-- just live with it. If I rev the throttle a bit while letting off the clutch, it engages much more smoothly, but if I do this at idle it shakes violently.
The one weird thing is that it doesn't do this when the engine is cold. For the first ten minutes of driving, the clutch engages smoothly like any other car, but as the engine comes up to temp the shaking returns. This doesn't sound like the flywheel to me.
So my 07 with 125k miles has had new rotors for about 50k miles or so, but for a while now when the brakes get hot it gets a violent shudder on braking at highway speeds....the odd part to me is nothing at lower speeds, and not always at higher speeds....do I just have warped rotors again? The rest of the front end I good and tight....
View 9 RepliesI purchased a 2011 ford f250 6.7 diesel today from a dealer in indiana. During test drive i noticed a shudder when i was doing over 60 and i immediately brought truck back and told seller about it.so he gets in and we drive it got it over 60 i hit brakes.it shuddered again but not as bad.long story short seller said it was prob a shock or strut or ball joint.
So I bought the truck anyhow and during the 600 mile drive back home and only when i was in top gear the truck would shudder when i hit a large bump.i would then slow way down to under 40mph and it would go back to driving normal.it did this a couple times but i noticed if i kept it under 60 it didnt seem to happen when i hit bumps.
So I get all the way home and check engine light comes on and i mean literally as soon as i got home from 600 mile drive. I plugged in my engine diagnostic tool and it shows a P0284 code. Are these things related? I called the dealer back and he says the truck is as is but he will look into it. I don't want to do further damage driving.
I have a 2002 F250 with the 5.4 triton engine. Automatic transmission. When I reach 35 mph (sometimes sooner) the truck will shake horribly when I reach lower rpms. It will do this up to 65 mph and then it mostly stops. Completely taking my foot off the gas will stop the shaking, as well as shifting into neutral.
I know for sure that the truck has a cylinder 3 misfire as well as a minor exhaust leak, could either of these be causing it? Don't have the money to fix either of the problems for another couple weeks, is it safe to drive until then or should I play it safe?
1995 Chrysler LHS
I have a shake in the front end. It is similar to driving on a rocky surface and it shakes the whole vehicle. It occurs between 40 and 55 MPH and when I'm climbing a hill. At other speeds it is fine. If I let off the gas then it is fine as it coasts, even at those defined speeds.
I've replaced the struts and the wheel bearings and an outer tie rod. I had the front end aligned and balanced the two front tires.
Whenever I am driving my Subaru Impreza, the steering wheel shakes above 60mph and is a violent shake at 65mph making it unbearably frustrating to drive to school each day. Recently I had slipped on ice and hit a curb with the tires on the right side of the car. I took it to a shop to get the rims looked at, and ended up replacing the back right. The mechanic said nothing about the front one however. My question to you is; could it be that the front rim is also bent? Or that it could just be a buildup of ice. It is cold here, snows often and is never above 20F.
View 4 RepliesMy car begins to shake violently and hum loudly at anything over 70mph. It used to be 80mph but it has slowly gotten worse. I have checked the motor mounts and none appear to be cracked or broken. I have also had tires balanced and replaced, rims replaced, and the problem continues to persist. I was curious if the right axle could be warped? or this issue may be caused by damage wheel bearings. At any rate it has gotten unbearable decided to finally extinguish the problem.
View 10 RepliesPicked up an '03 Eddie Bauer v8 with the full time AWD knowing that the transfer case needed to be replaced, I got a good deal so it was worth it. It's still driveable but it binds in sharps turns and I get the occasional knock. I have two questions really, what is the correct PN for the single speed transfer case for this year model?
All the online ford parts store will give me is 7A195... well yeah, there's like a hundred different variations on that part number. And what year Mountaineers and Aviators will cross over to the Explorer? I've been searching ebay but their info is all over the place, no consistency. As an after thought, how difficult would it be to convert this to a 2 speed part time 4x4?
I have a 2003 f150 4X4. Whenever I go around a round about slowly, the truck sort of grind under the frame and shakes a little bit like I am in 4 wheel drive.
View 2 Replies98 Ranger Front brake lines Too short! they kink in sharp turns and wear out then start to seep then eventually leak and need replacement. Checked parts references and the lines have been considered stock. Not sure if I have a 1/2 year model.
View 1 Replies09 stx 2wd 4.6L- I have a 2.5'' leveling kit and 33'' bfg a/t tires. The problem is when I make sharp turns, or turn and go over small bumps. Whats happening is something seems to catching or rubbing it kind of jerks towards the opposite of where I am turning and causes the traction control to slow my truck (sucks on tight off-ramps/ u-turns). this happens at pretty much any speed although it gets worse as speed increases. At first I thought it was the steering stoppers but don't have any wear on them, tires do not rub anywhere. My dealer and a local off road shop cant figure it out...
View 9 RepliesWhen I make low speed sharp turns, (like trying to make a U or K turn) the Treg kind of "lurches". Is this common? Is there a fix?
My Treg is a V8 PPS and is one of the first here in the US (took delivery 7/7/03).