I have an 06 with a 5.4 with 70k on it and I have already had to do the exhaust manifolds twice, once covered by warrantee at 19k, then again around 40k and now at 74k I have a major leak from the left side manifold again
View 1 Replies2004 SCrew, FX4, 5.4 ... I had the dreaded exhaust manifold leak on the passenger side. After reading the horror stories of this repair and living in the rust belt I decided against fixing it myself. I took it to a local repair shop to have done. Initially the mechanic could see that the front 2 studs were snapped off (before even trying to remove them).
After a full day of fighting the studs (engine loose & lifted up) everything is out but the front 2 studs. the top one has about 1/2" exposed, but it is frozen in place (penetrate on it overnight). The biggest problem is the bottom stud. it is broken off about 1/8" below the surface of the head. The guy doesnt have a small enough right angle drill to get between the frame & head to attempt to drill it out. I will gladly go buy a drill for him to do this, as it will likely save me money if it will work to drill out the stud.
Need to get the 2 studs out, particularly the bottom one, or what right angle drill may fit in there?
Truck has 107 thousand miles; had to take it in for an manifold exhaust leak. Mechanic said bolts are so rusted they break.
1) was there ever a ALERT from ford about these bolt's?
2) Thought i read ford had stainless bolts for this problem...
I've had F150's only since the mid 70's and this 04 has cost me more in repairs than ANY previous F150..
I have a leak at the driver side exhaust manifold. Its a little tough getting at it to tell if its a lose bolt, crack or bad gasket. What would be the best way to get at this area? Should i remove the tire and wheel well or is their a better way. If i can get at it i may replace the manifold all together.
View 2 RepliesMy 05 Gx has the infamous manifold exhaust leak on the driver side. I'm planing to change it myself I don't think it should be that tough.
View 2 RepliesMy wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 Replies2005 Supercrew and my passenger side exhaust manifold was leaking. Son of a mother duck that was a joke to get removed. Front two studs broke off about 1/4" below the surface. Manifold is not cracked but putting a straight edge across it's out of plane at least a quarter inch.
Had planned on the dorman manifold but read some poor reviews about it cracking in less than a year and being warped out of the box. There is an ATP manifold with very few reviews but all good. Or just bite the bullet and do shorty headers? The driver's side looks a lot easier to access.
These trucks really weren't designed to be worked on after assembly were they? I had to invent new cuss words. Looks like Ford manifold is disco'd...
I have a 2006 F150 screw 4.6 auto 116k miles that has evidence of a small coolant leak where the intake manifold joins the head. This is on the drivers side directly under the thermostat housing. The t-stat housing is dry and the hoses all appear dry. It's just wet right at the gasket where the manifold joins the head. Reservoir is still normal so it's not leaking too much just yet.
I searched this site and youtube but didn't find any other posts. Lots of problems with older trucks with composite manifolds but nothing for this one. It looks like a part of the bottom of the manifold is plastic but the entire top and where it is leaking is all aluminum.
It seems odd that this would start in the winter time just driving back and forth to work (no load). And, yes the antifreeze is good. Just wondering if this is a known issue with this truck. Is it just a matter of replacing the gaskets or is there some other flaw I should be concerned about?
My friend and I are working on her '03 1.8t and I noticed a huge oil leak under the intake manifold. It looks like there's a tube that has broken off and is now just spewing oil all over the place. I tried to get pics the best I could, so here they are....
I'd imagine its something that needs to be fixed asap.
I purchased my 2008 Explorer Ltd about 4 months ago with a 4.6L and 63k miles. I use it for towing a small travel trailer, so I don't put many miles on it. It's got about 66k on it now. According to OASIS, it has had all MFR maintenance performed up to the 60k mark.
In the past two months, it has developed a "sound" on startup. it goes away after about 75 seconds. To me it sounds like a typical exh manifold leak. That "3 cylinder, putt putt putt tractor" sound. There is no apparent affect on performance. It is definitely coming from the area of cyl #1. I have a recording here.
[URL]....
It is the "higher" of the sounds. The lower pulsing/whooshing is just regular engine noise. You can hear the regular engine noise as the camera pans to the back of the car.
What puzzles me is that the exh manifold sound goes away after 75 seconds or so. Holding the tailpipe shut for a bit builds up lots of pressure quickly. Do you think it IS, in fact, an exh manifold leak, and it seals up with thermal expansion as the engine worms up (75 seconds)? Is this a typical issue with the 4.6L
I have V6 Tdi -08 and my car has developed a tiny leak on the right hand side exhaust manifold. The purchase price for a new manifold is not to expensive but I now wonder difficult it is to replace considering how tight it is in the engine bay. If the engine has to come out in order to have it replaced or repaired.
View 4 Repliesis there a set of headers for my 2008 f250 5.4 rwd that will install somewhat easily without me throwing tools across the garage? I see a lot more options for the older trucks. I have a pretty annoying exhaust manifold leak and I figure I might as well throw some headers on if im gonna be in there. I really want to go for sound rather than power. I think I saw a set by flowmaster that looked decent.
View 6 RepliesI have an exhaust leak on the passengers side of my 2006 F-150 5.4 triton. If I do the repair which is the correct way to do it? Do I replace just the blown out gasket?
Do I need to buy a new exhaust manifold and gasket kit, with exactly what parts should I buy in the kit? Or do i need to replace both sides?
Should I attempt to replace the passenger side manifold with what I can get from Napa. I would rather pay 100 bucks for everything and do it myself. But, Im concerned about replacing the studs. From what I have read the studs seam to be the problems for most leaks on these vehicles. I have torque equip. and other tools to do the job. Just want others opinions about this project. How hard really is it? 1999 5.4L F250 SDuty....
View 14 RepliesSo I started my truck this morning and it sounds like air rushing out from the driver side of the engine. I currently have my ICP unplugged due to a bad sensor, will be replacing it on Sat. Also I have been having an issue with my turbo but I don't think that it's related as I here the air rushing sound when at idle as well at when driving. It seems to be a bit louder when the engine is cold but I could also be crazy about that.
View 3 RepliesI just finished installing a new turbo (shaft play and lots of oil in the compressor side), RR up-pipes, and T500 (250k and once had a very long crank to get the ICP up to start).
Anyway, except for another exhaust leak at the pass side up-pipe to manifold, it seemed to run okay but with lots of white smoke. I only have about 50 miles after the install, when it suddenly starting surging and made a lot of loud knocking noises. This then went away and came back again rather quickly. I was close to home, so I made back under power. I also received the two codes listed. My IPR is original, but two summers ago I installed the IPR re-seal kit. Everything on the IPR looked good when it came off for the T500.
After reading around, I saw that low fuel pressure / air in fuel can cause problems. I connected a pressure gauge to the pre-filter port on the filter housing, and got 40psi at idle. I then took a diesel shower and blew out the fuel line into the tank. After re-connecting it, the fuel pressure stayed the same but the engines idles much better, but still has blue smoke. It's the original fuel pump (to me anyway) and original fuel line connections.
I have about 3/4 tank, and no place to put it, so I'd need to run it out for the Hutch mod, or least to get in there and inspect. Would eliminating the Ford connections at the pump be worthwhile for now, and is 40psi at idle adequate? Wondering if it's time for a fuel pump?
Attempting to take this on myself. My passenger side manifold was replaced a year ago.....BTW This damn truck - all stock - no modifications of any kind - just turned 100k miles. One owner - me.
So I have removed everything I think I need to to gain reasonable access including the fenderwell and all the intake tubes and battery and coolant reservoir. I want to use some heat and try not to break the bolts but there is a thin wiring harness just above the exhaust manifold. I can't find it in any diagrams on the ford parts site. It looks like the glow plug and injector harnesses are up above near the intake manifold but this one is down below all that. It connects to small rubber thing - 1 for each cylinder. There is nothing else electrical near it - everything else is up top.
Now my rant - look away if you are a die hard ford truck fan or 6.0L powerstroke fan.
So far I've had to replace both exhaust manifolds because they burned and rusted right through. New transmission cooler lines -yes - rusted through and cooler (because we couldn't get the lines off without destroying the cooler). Cat got clogged (that was fun to find and fix). All 4 front ball joints replaced. Transmission dip stick tube rusted through. Several brake lines had to be replaced due to rust. The air conditioner quit with about 80k miles. I haven't fixed that yet. My oil pan is rusting through and needs replacement. Friggin oil pan! I have never in my long life experienced that. I know of other diesel pickups that are older with far more miles that live in the northeast, used for plowing and never garaged that don't have their oil pans rusting through. Just had to change both power steering lines that go to the gearbox due to leak caused by rusting through. EGR needs to be cleaned or replaced almost as often as the oil need changing. This POS needs to be out of my life!
Too bad because if it was dependable and wasn't made out of the cheapest crappy metal Ford could find it would be a great truck. Rides and hauls great. Plows great. Good looking truck, too. Standard cab 8 foot bed. Dark green. Just can't keep doing this.
I have a 97 Expedition with the 5.4 engine and 160k miles. Recently while having other work done I was told that I had an exhaust manifold leak due to broken rusted bolts.
View 3 RepliesMy truck just started running really loud when it's cold and the leak goes away when it warms up to operating temperature.I did a little bit of investigating and I have found where the leak is coming from at the end of the exhaust manifold where the donut gasket meets the catalytic converters. It appears that the bolts rotted that hold the system together at the gasket. What should I do to repair this? I don't really want to replace the whole manifold because I know I'll break a stud off in the engine because everything is pretty rusty down there. I even took some pictures of the problem....
View 3 Replies2006 F150, 4.6 V8 ... My truck was running fine until one morning I was sitting in the truck giving it my customary 30 second morning warm-up and it starting running very rough and quickly threw Check Engine LED.
I hooked up my laptop and got the following error codes: (To assist with future searches, the error codes are P0302, P0303, and P0353)
It seemed to drive fairly well, but low RPM torque causes major shuddering, so I try to keep the revs up to avoid damaging other components. The first step was to replace the spark plugs. They looked to be original and I'm at 140K on the truck, so it's probably time.
I went with Bosch Platinum as the factory plugs were platinum. When replacing the plugs, I moved the coil pack from cylinder 2 to cylinder 3 to determine if the problem would move. After the plug swap, the engine did run noticeably smoother (so the plugs worked overall), but still had the low rpm shudders and the same error codes (after clearing them).
Unfortunately, the error codes still indicate cylinder 2. I guess a misfire could be related to the fuel injector as well, not firing at the right time or not a complete spray, but what else could cause this?
Whats the best way to get at the driver side exhaust manifold? I have a leak and its tough to get at. Should I remove the tire and inner wheel well?
View 1 Replies