I just bought 2006 f150 4wd . It make a grinding sound on both sides in the front end..it seems to be independent and when I slow and come to a stop, I makes a clanking noise like its locking something in.
View 4 RepliesI owned a 99 f250 a little while ago. Just bought a 2006 crewcab F150 xlt about 2 months ago, and for the past month there has been this unusual grinding or whirring like noise coming from the front passenger side wheel.
I took it to the mechanic and he found a bad wheel bearing on drivers side and replaced it but that wasn't the issue. He could hear the noise but wasn't able to figure out what the actual issue was.
The noise only happens when my foot is on the throttle. (not when coasting) and i also just discovered that it doesn't make any noise at all when put in 4x4.
2005 ford f150 Fx4 So last Friday I started hearing a grinding noise from the passenger side front of my truck. sounded like metal on metal. So I started rooting around and noticed that bottom ball joints were shot. so replaced bottom ball joints on both side. I aslo replaced wheel bearing hub assembly on both sides, still heard the grinding. So I noticed that both axles were slinging grease, so I replaced them on both sides.
Still heard the grinding noise. So then I removed everything from the passenger side and noticed that the locking hub actuator was grinding both axle and the wheel bearing hub. So I just got done replacing that on the passenger side, put it all back together, and still grinding noise ringtones free. Also replaced the 4wd solenoid that they said gets water in it, and I replaced the check valve. And I put new Rotors and breaks. What it could be?
I have an intermittent grinding noise coming from what sounds like both front wheels, it sounds like metal on metal almost like something metal rubbing the rotor but I just put new pads on and the noise was there before as well with nothing touching the rotors but the pads. The sound will appear out of no-where at low speeds of 35 or below and will continue until I brake and slow down, just before I come to a compete stop the noise will stop with a slight clunk.
I can then drive away with no noise. I am pretty sure it is not brake related except maybe ABS somehow but was also thinking front axle or diff, also have read posts that are bearing related, but both at the same time?. It is the slight clunk before stopping that I can not figure out is related to. It is an 05 f150 xlt 5.4 super cab 4wd with 85k miles
I've got a new issue that is happening on the front end of my truck. Whenever I try turning my wheel while driving, I get this rubbing/grinding noise coming from the front of my truck. It only happens when the wheels are in motion. It seems to happen less when I'm driving at higher speeds, but I can notice it make the sound at any speed. I tried driving it slowly in an empty parking lot while turning and it's definitely making the sound every time the tires rotate.
I took it in for an alignment because this was happening every time I drove, whether it be driving straight or making a turn. Now that my alignment has been fixed, it no longer make this noise if I am driving in a straight line, so it only seems to happen when I'm turning. I had the mechanic check to see if they could reproduce the issue. The mechanic was able to hear what I hear, but when he put it on the lift at the shop, he was not able to reproduce the sound.
2011 Isf with noise coming from the driver front and both sides rear. Have Bc coilovers, and checked them but they're good. Everything tight I double checked and torqued. I wanted to say it was tierods but tierods wouldn't make noise this is more of a rubbery thump. sounds like a boot or balljoints .
[URL] .....
2004 F150 SCREW Lariat 4x4. Experiencing some odd noises. When driving down the road and turning the wheel slightly left will produce some grinding and popping from under the floorboard. I'm suspecting a CV axle as the boot is ripped on that side. Would this have anything to do with the IWE system or solenoid??
View 1 RepliesI am getting a grinding sound from the left front wheel while driving straight.. The sound stays the same when brakes are applied and does not change when selecting 4wd or 2wd.. I pulled the wheel off and had a look, but saw nothing unusual.. What are the steps to diagnose/repair the issue? 2004 F-150 5.4 4x4
View 6 RepliesRepeat Front Hub Failures -- 2WD Try this situation -- Purchased 2006 F-150 XL with 57,000 miles. Truck built on 05/24/2006.
Sept 2011 68,621 miles -- Left front hub failure -- Wheel bearing grinding -- Done by Bell Ford in Phoenix.
2013 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2014 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2016 -- Upper & lower control arms, struts, strut mounts, springs replaced -- Quality part used -- Complete front end alignment -- Brake job front and rear.
Nov 2016 -- New performance exhaust system due to exhaust leaks.
Dec 2016 -- Failed automatic transmission -- Remanufactured FORD transmission installed w/ 36 mo warranty. Sanderson Ford gets an A+
March 16, 2017 151,000 miles -- Left front hub failure -- wheel bearing grinding! Verified by jacking up truck and spinning left front wheel -- GRIND! This is coming from down in the hub. This is a 2 wheel drive truck. Yes, you counted correctly, this will be the 4th replacement on the Left side!
NO Towing! NO Overloading! Wheels are 2006 XLT style Aluminum rims with P235/70R17 Michelin XLT M/S (Defender LTX) tires all around.
It only hauls maybe 200 to 300 pounds of electronic equipment at the max, once in a while. This is driving me crazy! I always use FORD PARTS for the HUB ASSEMBLIES. Really loosing faith, the front right hub is OEM original - NEVER CHANGED!
About 3 months ago I started having a grinding sound from the front driver side hub area. I replaced it and it fixed the problem. I read where you should do both because he other one is soon behind it but I waited. Now I started hearing it from the passenger side too. So I replaced it today and all was good until I tested it from 4 wheel back to 2 wheel. Once I went back to 2 wheel the clicking that sounds like bearings going out to me, was back. What is it?
View 1 Repliesmy 2006 f150 fx4 super crew power windows wont go down on the passenger sides. The driver side works fine. i went the owners manual and changed our the fuse in the fuse box and same thing still. just to make sure, i put the fuse and tried the driver side and it did not go down. what could it be? should i just take to one of the local mechanics and have them look at it?
View 3 RepliesI have a 2004 F150, 5.4L V8. A few years back I was in an accident when someone slammed into the front of my truck. The right front wheel & tire took the brunt of the accident. I thought the repair shop had everything back to normal until recently I occasionally have a grinding sound coming from the right front side, seems to be related to the axle. It doesn't do it all the time just at random while I'm driving. The only solution I can find is to pull over or slow my speed to a crawl. Once I slow down enough or turn my wheel one way or the other its like something SLAMS back into place. I had it looked at by a local mechanic and they couldn't find anything wrong. Could it be something in my right front axle?
View 7 RepliesRead everything I could and couldn't find a problem/solution similar to mine:
- Replaced broken (in three pieces) actuator on driver's side. Also replaced hub assembly (bearings went bad). Afterward started getting the grinding noise all the time in 2wd that goes away in 4HI.
- Replaced the entire hose assembly since I was not getting vacuum at driver side end hose. Still wasn't getting vacuum, turns out passenger side actuator diaphram was completely torn up as well (checked vacuum with hose on passenger actuator, not removing and plugging like I should have), so replaced the passenger side actuator too.
- Driver side grinding noise went away completely, now getting grinding noise on passenger side ONLY WHEN PRESSING ACCELERATOR. Take foot off accelerator and coast down road/highway noise goes away. Noise also goes away when putting truck in 4HI.
My latest actions: I've checked vacuum at both ends of hose while someone in park throttles truck up to 3k rpm, vacuum doesn't appear to change at either hose end while opposite side is attached to its actuator. Replaced passenger side actuator again thinking the first was defective, no change in grinding noise. Greased ring on wheel hub where actuator attaches thinking I was getting a leak at the actuator/hub seal, no change. Still only a grinding noise when accelerating, not while coasting with truck running.
The perplexing part: If it is a vacuum issue, how is it I am getting good enough vacuum from the driver side but not from the passenger side, since the driver side hose connection is downstream from the passenger side? Also, how am I not seeing the vacuum drop when checking at the hose end of either side while someone throttles truck up in rpms?
My thoughts: Definitely a vacuum leak somewhere in the system, minor enough to not notice right away on gauge, thinking to check the vacuum box and check valves next. Also thinking the passenger side hose from solenoid has a small leak causing the issue on the passenger side and not the driver side anymore, so thinking of putting the old hose back in to see if there is any change (I had replaced the hose prior to knowing the passenger actuator was torn up so I am not sure if the hose is really bad).
3-piece actuator I described above in picture for reference. Honestly I was not surprised, this has been my luck with this truck.
I've got a 2006 f150 4x4 v8 ... I get a grinding noise (I think it is coming from the front left of the truck) that lasts only a little while and only comes out after a cold night (so I only get the noise in the morning after the truck has sat overnight)...
The issue details:
1. The grinding noise is constant and the truck has to be moving for it to make the noise
2. The truck will only make the noise while driving forward, it disappears when I drive in reverse
3. The truck has to sit overnight and it has to be cold (below freezing)
4. I only get the noise if I go in reverse BEFORE I drive forward after the truck sat all night
5. Will not make the noise while in 4x46. It has been doing this for about 2 months
What I tried:
1. Replaced both front wheel hubs
2. Replaced 4x4 vacuum and checked the lines for pressure
3. Front brake pads and checked calipers
4. While the truck was making the noise unplugged the 4x4 vacuum - still made the noise
I've had a grinding noise coming from the front passenger side, sounds like the wheel area of the car, for many months. I've driven thousands of miles on it like this, mostly because I'm broke and the car otherwise runs fine, but also because when I've taken it to mechanics, they are stumped.
I took it to a shop about a year ago and he had it for a week, had different specialists look at it and ruled out anything mechanical (wheel bearing, etc.) In the end, he threw up his hands and didn't want to give me any more free labor for his non-diagnosis, and thought he ruled out everything but the transmission. I took it to a transmission shop recently, and the guy ruled out right away that it was the transmission. He tried to diagnose the problem and was stumped too.
Here's what it is doing. It makes a grinding noise around the front passenger wheel when I accelerate. Only when I accelerate. It seems to be more active when it is cold, and after I've been driving the car for about an hour or so, it goes away. It used to only really happen when taking right-hand turns, and that is still when it is at its worst, but now it does it anytime. However--some days it is very bad and some days very light. One day--of course the day I designated to take it to the shop--it stopped altogether and drove like new. Just until I got it home. It is worse in low gears, and used to only happen in first, second and third, but now on an active day I can hear it on the interstate in fifth gear.
The shops I've taken it to can't seem to figure out what it is. Reading threads online, I've learned that people with similar problems found the problem was a bad passenger side motor mount. I have the car at a new shop right now, and I asked them to replace the motor mount, even though it looks fine. I had a long talk with the mechanic there today and he seemed a bit skeptical, but thought it was a possible solution.
Should I spend the money on a motor mount even if it looks okay? (I've also read that the Focus mounts look fine from the exterior when they are bad because they have a gel interior that busts). Especially if this doesn't work, I'm going to be back at square... um, zero.
Every time I brake, there is an awful grinding sound in the rear of my truck. It doesn't seem to be affecting the brake strength, however something is obviously wrong. I have looked at the brake pads and they seem to be in good shape. I am a mechanical misfit, but I hate getting ripped off by other people at the brake shops.
2005 F150 Crew Cab, 5.4 V8....
First I will start off by stating that my truck is a 2005 Ford F150 2WD Regular Cab 6.5 Bed, with the V6.
My problem is, when making a left turn at low speeds, I have a grinding noise that corrects itself upon straightening out the truck. This seems to happen on turns in the parking lots etc. It almost sounds like the tires are rubbing but the tires are the same BFG's that have been on the truck for 40,000 miles and have never rubbed. I am thinking it might be the power steering pump but am unsure. I do not have access to a lift right now but I have done the shake test on all of the suspension components and nothing seems out of place or loose.
I have a 2005 F150 113,000 FX4. When I put the truck into 4x4 high the light comes on and the front driveshaft engages. Same with 4x4 low. the problem is that the hubs never actually lock. When I move forward in some mud or wet grass the right front hub makes this grinding noise like it is actually trying to engage but never does. Same with 4x4 low. I do not have any weird noises when I drive in 2wd.
View 6 RepliesWe've had a lot of rain here in pa lately and i hit a few big puddles the other day and now i have a growl slash wine in the front of my motor,now i narrowed it down to something driven by the bely because I removed the belt and no noise all pulleys feel good and smooth except the ac compressor if you spin it by hand it has a rough/dry feeling and sound to it but the noise doesn't change with the ac on or off its just constant grinding/whine. Replace the ac compressor pulley bearing that what I am thinking it is and don't really want to change out the whole compressor..
View 1 RepliesOk here goes. I recently replaced the front wheel hub and upper and lower ball joints on the the driver side of my 2004 f250 CC SB 6.0 fx4. Now when I put into 4 wheel drive I get a grinding noise that sounds like a worn out break pad from that side only. It didn't do it before and it only happens in 4x4. I have replaced the wheel hubs before and it was fine. Also The needle bearing race on the axle is good.
View 2 RepliesI have a grinding noise coming from what I believe are the front brakes. It happens when I apply the brakes and sounds like the brake pad is worn out and there's metal-on-metal contact but when I checked the pads, they are at 80-90% (rears have about the same amount left). I hear it the loudest just before coming to a full stop, from about 20 mph down to stop. I thought it was caused by rust on the brakes but after I wore off the rust, the sound is still there.
View 14 Replies