Ford F-150 (2004-2008) :: 2006 - Engine Won't Crank - No Start?
Jun 2, 2012
I was working on trailer lights and now no trailer lights and relays click but eng no crank. Batt has 12volts.
View 1 RepliesI was working on trailer lights and now no trailer lights and relays click but eng no crank. Batt has 12volts.
View 1 RepliesI have a 2006 Ford Expedition with 95,000 miles that has a crank but intermittent no start problem. When it does happen, it will eventually start after one to two tries. I don't have to wait to start it again and I don't have any problems while it is running. Two or three times in the past two months it will sputter out and die (even though I am pressing the gas pedal) right after starting. I'll crank it again and it starts just fine. I have no problems while driving at freeway speeds or around town.
I never had any check engine lights come on so I replaced the battery and the fuel filter. I finally got two codes and replaced the fuel pump driver module and the fuel rail pressure sensor. The codes went off after replacing these two parts. I can hear my fuel pump turn on every time I start the vehicle. I have even taken the entire fuse panel apart to check Relay 303 which is soldered into the circuit board. It is fine and so is every other fuse in the panel.
Wifes F150 was turned off while she went shopping when she came out it would not start would crank but would not run. Got it home hooked up my scanner, had no codes, but the Service Engine Soon was illuminated on dash. Just wondering if this has anything to do with the PCM. Has a 4.6L engine, 2X4.
View 5 Replies2008 F150 XLT 5.4L
1. Replaced fuse #9 for fuel pump.
2. Checked fuse #9 with check light, power to both sides is good
3. No check engine light
4. Battery is 1.5 years old. Just in case I charged for 1 hr.
5. Replaced fuel filter. Possible clog in fuel line.
6. Detached fuel line at fuel filter, turned key on and fuel came out of line. Seems like fuel pump is working.
7. Every time I can hear the fuel pump prim when I turn the key.
8. Relay#1 starter solenoid, I swapped with relay #2 and also replaced
9. FPDM replacement, I removed and it looked to be good.
10. Light checked all fuses, only fuse #5, fuse#35, and Fuse#36 did not have power. These fuses don't seem to have anything to do with starting or fuel to the engine.
11. Inertia switch check is good
I have an 06' F-150. Last monday went to start and wouldnt crank over. I have since replaced FPDM, a weak fuel pump, checked Fuel Inertia Switch and now that they are all replaced when I check codes it says "no data available". Pump will not come on. Fuses have been checked. I have traced this problem to everything I can think of. If my ECM is fried, why would it have worked fine before replacing FPDM? I am at a dead end. Mechanic is at a dead end.
View 9 RepliesWent to leave this morning and my '05 with 135K would crank but not start. Pulled air cleaner and sprayed a little starting fluid and it fired some so I had a feeling it was fuel related. Reset the fuel cut-out with no luck. I then remember seeing the issues on the forum about the fuel pump driver module corrosion and failures. Bought a new one at the local dealer, installed it and it fired right up.
Pics below...from the side it didn't look to bad but was holed through on the bottom. I highly recommend replacing this if you live in the rust belt.
I have a 2006 F150 that cranks but will not start. I sprayed ether into intake and got it to start but engine dies if gas pedal pressed. It idles after starting just will not accelerate.
View 8 RepliesSo I used my 07 F150 4x4 Lariat (5.4 l) yesterday and it ran with no problems. Today, I went to start it to go to work and it would crank over strong and fast but not run. I filled up two days ago and it has been below freezing the last couple of days. What to check as I currently have my wifes explorer for work tonight.
View 14 Replies06 5.4 screw. This truck sits in the garage all week long as I drive a work van daily. When I take the truck out on the weekends it starts up normally at the house and when I stop someplace for a few minutes it starts right back up but if it sits for an hour or more it will crank over for 10-15 seconds, it does always start back up. It always runs and drives fine, it is all factory as far as the motor, intake, exhaust, tuner etc. What to do with it.
View 12 Replies2004 New Body F150 5.4L
Removed all cops, plugs, intake manifold and driver side head to repair bad valve. Removed Left side cat pipes as well. Had to disconnect most of upper engine harness and had to remove cpm and battery.
Repaired all mechanical issues and reconnected all electrical connectors and now when I turn the key to start the red security light on dash is still blinking steadily and I get no crank no start situation and it blows #34 PCM fuse which is injector/fuel fuse as soon as hit start.
Here are some things I have done trying to trouble shoot.
Battery shows 13.65 V
Unplugged FPDM back on rear frame rail and disconnected far left harness (looking from front) from PCM (should be engine harness), both the smaller plug that plugs into another harness and the main plug to the PCM.
Now when I turn on the key the security light goes out, the dash display says engine fail safe mode and the motor will turn over when I turn the key. This is still with the #34 fuse blown.
If I plug the engine harness back into the PCM, same no click no start.
If I leave engine harness unplugged from PCM and plug FPDM back in and turn key now it goes back to no crank no start and the security light blinks rapidly.
Only way I can get anything to turn over is far left harness disconnected, both plugs and the fdpm disconnected. Display says Engine Fail Safe Mode, and the security light goes out when I turn the key to start. I'm at a standstill as to what to do. The truck started fine prior to me taking it down for service.
I have a 2007 F-150 5.4l that does not crank when you turn the key to start. I have tried jumping the starter over and it does crank after that but it will not start. I am completely stumped by this and I'm not sure what the problem is?
View 2 RepliesI have an 04 f150 and just changed the alternator yesterday, and 4 hours later it wouldn't start starter clicks but no crank.
View 3 Repliesford f 150 2005, engine wont crank over. Tried all these remedies but none of them work. [URL] .....
Here was the scenario: someone drove my truck in 4 low for a very long time.3 hrs doing over 80 km/h) When i drove the truck i could get it out of 4 low it is still in 4 low. But then the truck died on me.
The alternator pulley went on it. replaced the alternator then proceeded with the remedies from the link above.
No crank with key, can jump and it will crank over, no Radio in RUN position, work fine in ASSy position. Engine will not spin over at all with key. Truck low miles like new, what gives? All fuses good and check a full 12volts on both sides. 2008 - 5.4 ....
View 5 RepliesI have a 04 heritage f-150, V6 I bought a month ago. Truck ran fine till tonight. Got in to start it, the engine started to crank and everything went dead except for a busing click some what like a turn signal. When I raised the hood the light weakly flashed in time with the buss. I checked the cables, clean and tight. The click came from the #2 ( I think) relay. I wiggled it and it stopped and the lights came back on but when I turned the lights on it all started again. The book says the #2 relay is for the PCM. Don't tell me the computer is out!
View 2 Replies2008 Azera with 90K miles won't start or crank. Unhooked battery and hooked it back up--no joy. No lights on the dash--absolute silence when turning the key. Doors and trunk won't auto-unlock. Can't get it into neutral to move it so I can try to jump it. Almost like it has some kind of kill switch.
View 1 RepliesI've Sonata 2006 and it's just fine no problems at all, until this problem comes. When I start the car the engine crank but not start, RMPs is jumping to 4 then into 0.. I checked fuel pump, battery and sparks all are good.
View 4 RepliesI have a Hyundai accent 2007, I guess the brain box is faulty, the engine will crank fan roll etc but won't start at all, can dis reset work for it at all ...
View 14 RepliesFuel Pump and Fuel Pump Relay replaced after 115,000 miles. On occasion, engine will turn over but not crank ... wait 10 minutes and the engine will start. No security light (passlock) or engine trouble codes displayed or recorded. Once the engine starts, it runs smoothly and normally. Problem of starting did not occur until the fuel pump and relay were replaced.
View 4 RepliesI have a 2006 4.6L that's hard to start when it's relatively cold outside.
Normally, when it's warm outside, I can barely bump the starter, and it starts right up. But when it's cold outside, it usually takes 3 or 4 2-3 seconds of cranking before it starts. Even then, it has a really rough "about to die" idle, until about 10-15 seconds, and then it idles without a problem. Once it's running, it runs great.
It has 79k miles on it, and all I've done to it is put in a throttle body spacer, and a K&N filter. I've read a few posts from people that have had similar issues, that had K&N filters, but their problems have been more consistent. Mine only seems to happen when it's first started.
As far as I know, the plugs have never been changed, as with the COPs. I've heard about a vacuum line running to the throttle body may be the culprit, but haven't been able to find any more details on that, like where the line runs to, possible replacement part number for it, etc.
My Lexus Rx350 (2007) having problem starting the car when the engine is cold or switch off more than 1-2 hours. I need to crank the car at least 2-3 times to get the engine run. Once the engine run, i have no problem restarting the car with a single crack.
View 5 Replies