I have a 06 F150 and I am getting the P2207 code on it. Sounds like a O2 sensor has gone bad. From reading a little about it online, it sounds like there are (3) different ones on the truck. Is there any way of knowing which one has gone bad or do you just have to replace all of them? How hard of a job is it, do you need a special tool to remove the old sensor?
View 1 RepliesProblem: Initially thought replacing the rear wheel speed sensor on top of the differential would make the light go away on a 2007 F-150 XLT. What I've done already.
-Replaced the sensor
-Used the IDS ford computer to clear the code
-Test drove it for 30 minutes and the light is still on
-Reset any codes by disconnecting the battery
-I have gone as far as swapping a different ABS module thinking it was the problem, after it was re-programmed the module checked out and it wasn't at fault.
It must be a wire, all the fuses for the ABS system are fine.
Issue or traced all the wires and found a common problem such as a pinched wire or melted wire between the module and the sensor? From what I have been researching this code B1230 .
-bad sensor
-sensor grounding out somewhere
Attempted a multi-meter test today and didn't get very far.
I just acquired a wonderful 2005 F-150 XLT 4.6 liter truck. I need to get it passable for smog check here in AZ and the failed test revealed a P0453 error code (EVAP) which translates to a possible pressure sensor malfunction.
My question is finding the sensor and if I am looking at dropping the fuel tank to service/replace the sensor. Also, could a vacuum line be the cause?
Throttle body failures on the 5.4L 3v are more common than you think, luckily it will pop a code for the throttle body more often than not diagnosing. Symptoms include start and dies, no start, a really rough idle, surging idle up and down more so in park, poor brake assist due to rpm fluctuation and wrench light on. If you find yourself in this situation I show you how to change the throttle body and reset the pcm to learn the new idle trims.
Ford F150 F250 5.4L 3v Electronic Throttle Body Replacement P2135 - YouTube ....
My wife's 06 expedition 5.43v runs rough loud and dies. Not all the time just when it's to hot. I got a code it's p0022 cam sensor. I changed both started the rig up and heard loud rattling like metal maybe chain. It lasted for a the length of my video 1.4mins give or take then went fine, i turned the car off and back on everything seems fine. I know I got her oil done after driving. She had metal/plastic in her oil. I had all plugs done and actually i re did the 8th cylinder plug because it was miss firing and i pulled it by hand with only the socket no ratchet. I'm thinking the chain is going bad if not already bad. Only 113k miles my 04 f150 5.43v lasted 250k before motor swap...
View 7 RepliesI recently replaced the timing belt, water pump, tensioner, all accessory belts. Made sure timing marks were spot on, did the 2 revolutions of the engine by hand, tensioner pointer was still in window per instructions. I noticed right after the car seemed not as responsive, or zippy, but did start and run fine for 340 miles. Than out of nowhere, it became hard to start, acting like it was out of time, so I removed top timing cover, doubled checked, everything, I even went as far as advancing the timing belt 1 tooth, than rotating engine by hand, than trying to start the vehicle. It still acted the same way, so I tried retarding it 1 tooth back from the original position, still the same issue. So I reinstalled it back to the correct position with, white crank mark @ TDC, and cam pulley hole lined up with the red painted groove in the cylinder head. Installed tensioner per Gates instructions, attempted to start, after 3 or 4 10 second cranks car will start and purr like nothing is wrong, take it for a test drive approximately 1 mile, car starts bucking, came back home. Pulled codes, tells me P2626 for o2 sensor.
View 4 RepliesI have a 2007 f150 sport. I am getting a 24 code on the airbag light and I do know that is Sensor output feed/return circuit open. What I do not know is where is this sensor located and what could it mean if I am getting the code...
View 2 RepliesI have an 06 F150 2wd that needs both lower ball joints. I've done searches and everyone keeps talking about a big freaking hammer. Can't you just use a ball joint press kit to remove and reinstall these? If no I'm gonna find someone to put them in for me because Im scared of breaking the aluminum control arm. There was also some talk of using some sorta glue on the joints as well.
View 8 RepliesMy 02 Explorer (XLT, 4.0) decided to throw a new code today. PO136, O2 Sensor Circuit (Bank 1 Sensor 2).
While it may be a wire issue, I still plan to replace the sensor. So the question is;
Can I get to it from under the vehicle or is there an access panel under the console like on the 2nd gens?
I have the sensor on order and plan to get it done on my days off next week.
"VSC OFF" light came on the other day. I took my RX350 to the dealer. The dealer said Heater Element sensor is bad. They didnot have this part in stock. I googled this part. Nothing comes up under that search. I took it to Autozone and the code came up as Mass Air flow sensor. Are both of these same thing?
View 7 RepliesThis started a couple of weeks back. It started with 3 codes, a misfire, bad coil and stuck rich. I have since done a tune up replacing all the spark plugs, the bad coil and even the O2 sensor. It is now at a point where the CEL is not on but it still throws the P2196 with a brand new o2 sensor just installed. I am stumped as what I should be checking for next. It seems to run ok but idle is not as smooth as pre-codes. The truck is a 2006 XLT..
View 5 Replies2006 F150, FX4, 5.4, super crew. Had the infamous airbag code 42 flashing at me the other day, replaced the sensor in the front of the radiator support, and am still getting the same code. The old senser had some corrosion inside the sensor itself, but the connections were clean on both the sensor and the pigtail. Is there something I may have missed?
View 3 RepliesI just bought a 2006 Texas Edition F150 with key less entry but the instructions and assigned codes did not come with it. How do I find what the code is to operate the system?
View 8 RepliesI have a 2006 F-150 Lariat with a 3.55 Ratio axle. What does the Axle Code H9 mean?
View 2 RepliesI have been having quite a rough time fixing a P0345 code on my 06 F-150 w/5.4 w/85,000. This truck has gone to a Ford dealer every 5K for the oil change/checkup etc.
Long and short - P0345 Code @ approx 83,500 miles, rough idle once the engine was up to temp and it would clear if you bumped the skinny pedal.
I have replaced the following:
--Both Cam Phasers
--Both VCT Solenoids (they both had holes in the screens - see this post [URL] ....
--Passenger side Cam Position sensor (I broke it pulling it out to do phaser swap)
--Spark plugs - SP515's
Issue was still present so then I replaced:
--Complete Timing chain set (Chains,Gear, Guides and Tensioners) - Drivers (left) side tensioner collapsed.
Once all back together and running the code is still there so I finally installed a REAL electric oil pressure gauge. Turns out I only have about 15psi at hot idle and 50psi when driving etc.
I am at wits end, because at this point I would have to guess that the engine is junk... Either a bearing is shot or whatever... Do I take the 3-4 hours to drop the pan to potentially see what is going on? Or just drop some 15W40 in the engine and trade it in?
I have a 2006 F150 with a cylinder #1 misfire only code p0301. I have done new spark plugs, new coil packs, and new fuel injector on cylinder #1 with no luck. What to do next?
View 5 RepliesFriend has a 2006 with the 4.6 motor. From time to time he gets a random misfire code ( I think its 0316).. He claims it will only do it when the gas tank is less that half full. I don't see any correlation between fuel level and the code. I am going to check fuel trim values, etc, when the code is set, this weekend.... all I can assume is low fuel pressure which sets the code... Any problem with the pressure module or fuel pump / discharge hose that is related to low level in the tank ?
View 3 RepliesI need to replace O2 Sensor which is Bank 2 Sensor 2 which needs to be replaced.
Where is this located on a 2009 Hyundai Santa Fe 3.3L
Have an 06 F150 5.4 3v with no power. spark knock. rough idle. wants to die while driving, and random misfire code. Have replaced fuel pump, filter, coils and plugs. What to check next? Already thought of EGR - it doesn't have one.
View 4 RepliesGetting code P2125. Read on here to get some electric contact cleaner and see if that works by cleaning the connections.
If I do end up changing out the Throttle Position Sensor, what voltage value do I look for when installing the new one ?
On my 2006 Ford F150 2WD, v6 automatic, the overdrive dash lamp is blinking, I get a engine light and the code I get is a P0743. That indicates the solenoid or wiring is bad, but everything works just fine. The transmission is running fine, clear fluid - no odor. The overdrive works and the truck shifts like new. When I start, the "OD-OFF" light immediately starts blinking and never changes. I can activate the OD normally and it doesn't effect the blinking light.
Where to start? I suspect that since all is functioning well, the issue is with the signal to the ecm? By the way, I can clear the code so that the engine light goes off, but the "OD-OFF" light remains blinking.