Ford F-150 (2004-2008) :: 2006 - Check Engine Light Started Flashing As Accelerated Uphill
Feb 12, 2015
2006 F150 Triton 5.4 Motor... It's been over a months journey with fixing this truck....
How it started: had an oil change, a while back, on long drive after, check engine light started flashing as I accelerated up hill so I pulled over and in a while it was ok, but couldn't get on the gas too much, or it would cause that flashy light thing.
So fast forward to now, after driving it with an intermittent miss for a while, was driving it to work and the miss became a shudder, and she stopped going over 30-40, and runs extremely rough.
Steady but loud idle.
Replaced all plugs with motocraft plugs and new coils all around. No change.
Finally hooked it up to a computer and got random misfires, now it's saying
P0174 bank 2 too lean,
But it's bank ONE that's the only side misfiring.
Here are the freeze frame details:
Frame 1 Mod $00
MIL Status Off
Troub Code P0174
Abslt TPS 24.3%
Eng speed 1665
Baro PRS 71 kpa
Calc Load 100%
[Code].....
View 3 Replies
Advertisement
I just bought a 2006 Subaru forester with 130K miles. Recently, the check engine light came and at the same time the cruise control started flashing. I brought it to the mechanic who said I had a bad catalytic converter. The car seems to be running just fine and now a day later the engine light is off.
View 3 Replies
Got an 07 Screw with only 50,000 miles. Yesterday, wife drove it home from work and said it would only do 45mph and didn't sound good. No warning lights were on, she said. I test drove it in the evening and it ran totally fine. Today, she drives it to work and said it ran real rough and "Check Engine" light was on. I picked it up from her work and it idles very rough and slow, and once you hit about 2000 rpm, it runs decent, maybe even normal. Below that, it stumbles and engine doesn't sound right. "Check Engine" light is either ON steady, or flashing. I don't have a code reader, so its likely going to the Ford Dealer Monday. Is there any way to read the code without a reader?
View 11 Replies
2005 F-150 4.6L 2WD, 268,000 miles....
Recently I got a flashing 'Check Engine' light and a rough running engine (along with a tapping noise) when I was passing someone (and pulling a trailer). I retrieved codes 300, 304, & 305. I can't swear to it, but I think the tapping noise started at the same time as the coil problem.
I replaced coils #4 & #5 (later that same day) and the engine smoothed back out but the tapping noise is still hanging around. The noise speeds up at higher RPM's and doesn't go away if I shift into neutral. Oil level and pressure are fine and I only use Motorcraft 5W-20 and Motorcraft filters (and change the oil every 5K miles).
Not sure if this is relevant: I think I have bad valve guide seals (blue smoke after long idles) but no other problems that I am aware of. It sort of sounds like a lifter, but is there a good way to pin it down? Is it possible that this tapping is related to the bad coils?
View 5 Replies
I have a 2005 f-150 street boss with 79000 mile, and it is shooting off going down the road, and the check engine light is flashing. The first time I started it back up and it would idle fine, but the throttle wouldn't do any thing. After setting about 15 min. I started it up and it ran good. I checked the codes and it had a p2104 Throttle actuator control system forced idle. It happened again with my wife. This time when I checked the codes it had the p2104 and a p2112 throttle actuator control system stuck closed code. What could be the problem, or a troubleshooting guide I could use to try and diagnose it.
View 6 Replies
Friday I pulled my steel gn 3 horse trailer about an hour each way. with the horses it weighs right at 7000 pounds. no issues. Saturday morning I drove to town, no issues. Saturday evening, I got in it to run down the road and about 2 miles from the house, the check engine light came on and the tow haul light started flashing and the temp gauge is dead. drives and shifts normal, tow haul button still functions. Truck is stock except for an EGR delete. No tuner, FICM was rebuilt. I had it on a battery minder before I left and was thinking about pulling the batteries and letting it sit for a while to see if it clears. Scan Gauge II shows no codes.
Sunday: So I let it sit all night, batteries connected and it was completely normal this morning. will see what happens when I drive it to work tomorrow
Later Sunday evening: So I just took it out for a test drive, went a couple miles down the road, shifting normal for a cold start. Temp gauge is working, just as I am almost back home. 5 miles at the most, temp is coming up to normal, gauge goes dead and check gauge light comes on and tow haul starts flashing. I think it might be the sensor.
This morning: I got about 6 or 7 miles from home, trans just got up to temp, pulling up a hill, it shifted out of overdrive, tft gauge went dead, check gauge light came on and the tow haul light started flashing. still shifts like it always has and the tow haul button still functions.
I am thinking it is just the temp sensor. Truck has 159k on it.
View 13 Replies
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 Replies
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 Replies
One day I was driving my truck 96 f150 4x4 Eddie Bauer edition and the over drive light started flashing and the truck got jerky going up hills. I got home and hooked my code reader up and (p0708) it said transmission range sensor. I replaced that the next day and drove it around town for about 30 minutes and parked it all seemed to good. But the very next day I started down the road and the transmission was slipping very bad after I turned around after a few hundred feet I barley made it back to my house. I checked my transmission fluid it's full and doesn't smell burnt or anything, I double checked the alignment on the neutral safety switch I just installed and it still in line. So I'm thinking my transmission is going out...
View 4 Replies
I've got a problem with a 2000 Impreza 2.5RS 5spd. It started with the check engine light coming on. A trip to Auto zone revealed that the O2 sensor was the problem. But on the way home, the light came on again and started flashing. All the while the car started acting like it had a misfire. It idles really rough and the exhaust smells like it's running really rich. I've replaced the plugs and wires, and all corners of the ignition coil check out properly as well. Can the O2 sensor cause a misfire in one or more of the cylinders? Or is something else that I should be interrogating as the cause?
View 5 Replies
A couple of weeks ago I was driving my 2008 Toyota Yaris and the check engine light came on. Soon after the check engine light came on every dash light started flashing. The Car down shift into second while I was going 55 miles an hour! We took the car into a service center where they said it was the speed sensor which they replaced. We got the car home. I drove it to work the next day and while going to lunch the check engine light came back on! The car seems to be shifting fine though! They mentioned that if the speed sensor didn't fix it, it could be the "cluster"! What the heck is that?
View 4 Replies
I have a 2006 F150 4x4 5.4. For a long time it idled poorly and would take 2 trys to start. Today it started shuddering and the engine light came on. The engine light went off but it still runs rough and smells of gas from the exhaust. It is not very drivable and I can't afford to take it in. I have lots of mechanical experience but not with this electronic junk and need diagnosing the problem. I have a code tester and this is what it said.
P0301 Cyl 1 Miss
P0304 Cyl 4 Miss
P0300 Random Multiple Misfire Detected
P2196 O2 Sensor Signal
Biased/ Stuck Rich
Bank 1 Sensor 1
View 7 Replies
I have a 2008 Santa Fe with 64341 miles on it. This past weekend we had it inspected at the dealer. Drove it home, in the rain/snow, and it sat in the drive way for a day while it was raining. This morning when I went to go to work, still raining, the check engine light came on and was flashing. Went to auto zone to get the check engine light code, the said that it was a P0303 which according to them was a misfire in cylinder 3. So I brought it to the dealer to leave it and have them check it out. On the way their the check engine light started to flash, when I walked in and told the service desk that they said that it was a catastrophic failure.
View 10 Replies
As the title says, my CEL goes on and flashes too.
I've read up a bit on why the CEL comes on/flash and it says it has something to do with the exhaust system and if continue operating will damage the catalyst converter (which I don't understand since I'm a car dummy.
In addition, the engine vibrates like crazy. I can feel the engine vibrating when I'm inside the car as well.
I already got the car tolled to the dealership and they kinda just told me it might be misfirings and then they said they couldn't locate the problem. So my car basically has to stay there until they open again on Monday and hopefully they will figure out the problem/fix it under the warranty and call me back.
The problem arise late Friday night and I just did a 30K maintenance on Thursday. (but the car already has 43,000 miles on it).
View 35 Replies
My airbag warning light is flashing 3 , and 4 which i assume is a 34. What this means? I have a 2006 Ford F150...
View 4 Replies
Earlier today i left my car idling for a couple of minutes and when i got back in and started to drive the car was vibrating, almost as if it was going to stall and the check engine light was flashing. drove a bit and stopped, started the car and now the check engine light stays on constantly. I have had the light come on (and remain on) a few times in the last while but it is usually solved by tightening the gas cap. it always seems to happen when i am low on gas (100 mile range-ish) Someone suggested maybe i had dirty gas in the car and needed stabilizer. My boyfriend said its a "misfire" and to change the spark plugs.
View 9 Replies
I have had this issue on and off for a while. happened about 2 years ago just after i bought the car, and just started last week again.
The car will be running fine, then will start to buck while accelerating, shortly after the check engine light will start flashing and the car runs like it is on 1 cylinder. shut of and start again, light remains on( not flashing), car runs smoother, but does not accelerate like it should.
took it to autozone, they said it was giving the code for random mis-fire, and O2 sensor.
2 years ago the dealer said it was loose coils, and they fixed the problem, all the coils feel tight this time.
2007 Sonata ... 3.3 V6, 70k
View 7 Replies
My Sonata has 150k on it and the tensioners have gone bad 3 months now. This AM i got a flashing check eng. light and the car runs rough. Any relation or am I looking at plugs or coil issues?
View 9 Replies
It happened randomly on the way home from work, the car chugged along with the check engine light flashing at me and then staying on. I was able to limp it home and got a ride to the nearest auto parts store to get some new plugs. I went with the NGK brand. Well, $60 later (including tools on the spot) and it's still running rough.
I know best case it to try and limp it to the autoparts store to let them try and pull the codes. I noticed an old thread where updates were made to the software to correct a running issue. I will note this same chugging randomly happened at 50,000 miles. I shut the car off, let it sit for a moment, restarted and it ran just fine. The engine vibrates noticeably just like it did at 50,000.
2009 Accent running rough 73,000 miles....
View 6 Replies
Kia rio 2006 130461 today I went and got gas right when I pulled out light began to flash and car shaking went to auto zone codes p0302 and p0326. I had knock senor changed 2 months ago . What could be the problem the guy said I just need a tune up . Is this true ? Is my car safe to drive car not shaking now and no changes in function of my car. There no way I can any one to look at it for couple begin tomorrow sunday.
View 19 Replies
This and the check engine light came on when I started the car this morning. Its an 06 GS300 with just under 53K miles....
View 5 Replies
