Ford F-150 (2004-2008) :: 2005 XLT - ABS Light Comes On But Brake Pedal Stops Pulsating When Depressed
Oct 8, 2011
Ok, I changed my front brake pads and rotors last week and since then everytime I get in the truck and drive for about the first 2 or 3 miles when I push the brake pedal it feels like my ABS sytem is activating. Then it stops and the ABS light comes on but the brake pedal stops pulsating when depressed. Is my ABS going bad or did I possibly do something wrong? I have changed the rotors and pads before without problems....
View 3 Replies
Advertisement
I have a 2005 Excursion 4x4 Limited 6.0 diesel. I had someone pull alongside me today and tell me my brake lights were out. Sure enough. I double checked and nothing at both lower lights and also nothing at the third brake.
So... here's the short version of the things I've checked so far:
1. no brake lights when pedal depressed.
2. running lights work fine
3. turn signals work fine
4. hazards work fine
5. brake lights DO illuminate when I press the brake button on my trailer brake controller
6. checked power to the green with red tracer wire going to the brake light switch on the pedal. 12 v present continuously
7. checked power to light green wire. 12 v present when pedal is depressed. 0 v when pedal is released.
8. checked power to tail lights (wish I had tried the trailer brake controller sooner, this step would have been unnecessary). voltage present (I think 10-12 v) when the running lights were turned on. 0 v when brake pedal depressed. I suspect now that I would have 12 v when squeezing my trailer brake controller button.
I was pretty convinced it was the brake switch at the pedal. But since I'm seeing the voltage pass through the light green wire when depressed.... I know the wiring to the lights are good because they work when pressing the trailer brake controller button.
So... Do I need to dig into the multifunction switch that I've been reading about? Does the power go from the pedal switch to the multifunction, then to the trailer brake controller? I'm really hoping that I don't have to dig into the column to check that multifunction switch!
View 6 Replies
Test drove an 08 V10 today. Brakes seemed to work fine and didn't lock up but I felt no pulsating in the pedal and heard no chirping of the tires like most ABS systems do. Is this normal? Anything special to look for in used late model V10s?
View 1 Replies
Having ABS issue with my 2004 Ford Escape XLT.
A bit of background information: every now and then (usually when decelerating from around 35-40mph), I will get a pulsating/knocking feeling from my brake pedal. At first, I thought it was the ABS, as I was told about a year ago that the ABS tone ring was broken. The more the problem manifested itself, the more I got to study it a bit. The pulsating/knocking in the pedal is usually accompanied by a very dry rubbing sound, and both the sound and the pulsating seem to be in direct relation to the motion of the wheels. I took it to the local garage this weekend and they recommended changing out the rear brakes - this made sense to me, as they haven't been changed out for as long as I have had the car.
Got the car back about an hour ago - on my way home, the pulsating came back when I was coasting into a stop light. The pulsating seems to have no affect whatsoever on the stopping distance of the car - a few times when it has happened, I have mashed the pedal, and the car comes to a quick stop just as you would want it to. After coming out of a complete stop, the brakes will work completely fine for a while - there seems to be no real rhyme or reason to what makes it happen.
View 10 Replies
I have another small issue with my 2004 Prius. I just noticed yesterday that the second I very lightly depress the brake pedal, a little clicking sound is made down below. It sounds like it might be coming from the brake pedal itself or somewhere underneath the hood. It's only when I depress the pedal slightly and it makes pretty much the same sound when I release the pedal. I just had a 5000 mile service done to the car and there were no issues then.
View 14 Replies
My brake lights dont come on until they are completely depressed. I think it may be the switch that connects to the pedal, but how do i adjust it in such a way that the light will come on sooner so everyone will quit telling me my brake lights are out?
View 2 Replies
I have recently purchased a 2007 Gen 2 Prius and sometimes it emits a very annoying squeak. It occurs when the car is stationary, with the brake pedal fully depressed. When inside the vehicle it seems to be coming from behind the glove box. When on the outside and facing the car it seems to be coming from below / behind the electric motor. I have made a recording of it with the noise in question being audible for a couple of seconds at 0:13, and then again at 0:22 until the end. It could be nothing I guess, but this is my first hybrid and I am not too sure what is perfectly normal and what is not.
View 14 Replies
03 F250 7.3. I busted a brake line last week somehow, Got it replaced and fixed up, Bled that line and everything was somewhat good.
Now, when i hit the brakes hard, I have pressure. If I let off even a little, My pedal will start to sink till i apply more pressure. I am gonna fully bleed my brakes when I'm home to see if this could solve the problem.
View 7 Replies
I have a 2004 Treg with 28k miles. This car has the air suspension and the dashboard with the LCD display.
When the foot pedal break is released, the break light remains on and the center display sounds off the alarm that the foot break is on as the car begins to roll.
After half dozen additional pulls of the break release handle, the issue goes away. This is now happening almost every time the foot break is used.
View 6 Replies
The park brake light stays on brake fluid level is good park brake is not on park brake switch is ok will sometimes go out but always comes back on .My son and one of my buddys also have a 2005 and have the same problem....
View 6 Replies
Why is there a sensor on the brake master cylinder? Most other cars and trucks I've seen have tied the cruise control into the brake light (and clutch interlock if Manual transmission.) switch so that when the pedal is depressed, the cruise control cuts out.
In the Ex, could I tap the brake pedal enough that the brake lights come on yet I don't trigger the pressure sensor in the master cylinder to cut the cruise control?
View 5 Replies
I'm getting this checked today most likely as it's been happening for months now. No issues with vibration and stopping is fine. As a matter of fact brakes are excellent. However when I'm stopped at a light or whatnot and I depress the brake pedal there's a pulsation that occurs almost every time. It's fairly constant and only happens when I'm at a stop not when I'm stopping so I know it's not a warped rotor. What it might be?
View 4 Replies
Brake pedal to the floor... And a lot of fluid on the ground.
I was coming home (empty fortunately) last evening when I noticed the brake pedal give an initial resistance, then slowly sank all the way to the floorboard when slowing down to turn onto my street. When I got to the house, I noticed a hissing sound each time as the depressed brake pedal sank to the floor. When I got out, there was a lot of brake fluid on the ground on the left rear side. It appears to be between the fuel tank and frame rail. From the side it is the section between the fuel filler to just ahead of the left rear wheel. The tank and frame rail is drenched and dripping DOT 3.
I am lucky to not have been pulling my 5th wheel when this happened! However, I have a camping trip coming up in a few weeks, but now my TV is broken. What has happened, and an estimate for repairs? Where is the best place to have it fixed, dealer or specialty shop? I just bought this vehicle in January and it has 102,500 miles, and came complete with full and meticulous repair records. The P.O. was incredible at upkeep, so this is something curious and flukey to me. But do I need to worry about the other side now, too?
View 2 Replies
But when I take my foot off the brake pedal , its just seems rather noisy (clunky). As if VW forgot to put some rubber or something to prevent this clunky sound. (it just sounds cheap)
My jetta and tiguan never seemed like this. Have to stick my head under there and see whats up
View 2 Replies
I have a 2003 Passat GLX 4Motion that was fine Monday...Having heavy rain Monday and with brake pedal depressed unable to get out of park..I have brake lights but when I got into car and started it I have airbag light and esp light on as well as check engine light...Is there a way to by pass the shift lock solenoid so I can move car into my garage...
I cleaned connections as was suggested and had a tough time as Bentley Manual states to remove console one must put lever into 3 which as lever is stuck in PARK was impossible...I tried pulling out the shift knob button as described and when I still couldn't get any response found that when I pushed the button back in that I was finally able to get shift lever to respond and finally come out of park...
I now get code for no TCM Signal P1626 No Powertrain Data Bus Signal Missing Message from TCM which now triggers ABS , Airbag ,ESP , and Check Engine light all with the cause no TCM Signal .... Now wondering if any easy way to test for data bus signal ?
View 2 Replies
Is the brake light supposed to come on when the E-brake is depressed? It's not right now, bulb?
View 5 Replies
We purchased the vehicle (2013 GX460) in September 2012, and had the car for 6 weeks before my wife was hit by an oncoming car who missed a stop sign. 8 weeks later and 23k of repairable damage to driver fender, front bumper, grille, hood, frame, and all components within those major areas, we received our vehicle.
The vehicle is wonderful and a joy to drive. When the brake pedal is depressed at low speeds (i.e., maneuvering in parking lot, entering driveway), there is a slight vibration to the pedal (similar to the vibration from a cell phone) and a noise that suggests an electric motor is working. The vibration is not like ABS; ABS is a profound vibration. The vibration we experience is very slight. The vibration is not apparent at highway speeds.
I do not recall either the vibration or the noise prior to the accident, and I suspect that this is a result from the accident or from the repairs. I have already brought the GX back to the dealer for this problem and they were quick to dismiss it, but I am really concerned that this is a real problem, and I want the dealer to re-assess.
View 13 Replies
My brake pedal is making a creaking noise when depressed and can also be heard when letting off the pedal. The noise is not coming from the brakes themselves (front/back are like new) but the pedal area or somewhere behind it. This noise doesn't start until I've driven the car for a little while. The brakes work fine for the most part but sometimes feel a bit spongy if making a sudden or hard stop. The fluid levels are fine.
I'm taking it in on Friday and hoping that the brakes just need to be bled a little or maybe the pedal just needs lube, but I'm worried it might be the booster or master cylinder---if it is one of these?
View 4 Replies
A couple weeks ago the front brakes were done on the Mazda. Then the wheel bearings needed to be done. I think the shop outsourced what I guess was the packing of the bearings. I paid for the work, and drove away, nearly, but didn't because I had no brakes and there I was pulling out into 5:00 PM traffic. The emergency brake saved me. I walked back into the shop and they discovered the power brake booster had broken. I wonder, because if you drove the Mazda to park it in the shop lot where the customers pick up the vehicles after repairs are made, wouldn't you notice that there is no braking action. The brake pedal was high and hard and there was literally no response when I depressed it.
The shop keeper said, darn I guess I'll have to replace this, meaning pay for it, since it (may have) happened when the bearings were being worked on. My question is, is there any reason why working on bearings might end up breaking the brake booster? Chances are, it was just coincidence, right? or? I don't know. Because the car is old, he had to take several days to find the part. Anyway, he sent me off and told me to drive it carefully. The drive home was absolutely nervewracking and required continual tugging up on the emergency brake stick. I wonder if they despise my car so much now that they are sending me off to drive in it in such an unsafe condition. Anyway, hoping it will be fixed tomorrow. But my question still is ... would working on bearings possibly be cause for breaking the brake booster?
View 9 Replies
My 2004 F 150 the rubber piece that goes on my brake pedal keeps on falling off after I put it back on looked it over today and did notice it does have a good size tear in one of the corners....Can I get a replacement one of these? all I need is the rubber that goes on the pedal....Would I have to go to the dealer for it?
View 3 Replies
What would cause the brakes on my wife's truck to be stiff and not hold?
View 14 Replies
