Ford F-150 (2004-2008) :: 2005 Truck Goes Into Failsafe Mode While Driving On Freeway
Apr 30, 2011
2005 ford f-150 Lariet goes into failsafe mode while driving on freeway. This is a dangerous situation happened ever.
View 2 Replies
Apr 30, 2011
Advertisement
Ford F-150 (2004-2008) :: P2106 Code - Truck Goes Into Failsafe Mode
Well my p2106 code seems to be different from all the other ones Ive read. I get the p2106 code after the truck goes into "FAILSAFE MODE" and it only goes into failsafe mode the moment the truck reaches 40mph and then loses all its power. I turn the truck off and back on and its back to normal until I go 40mph again. I scan it and only get one code p2106. The truck idles and runs perfectly until it reaches 40mph! I've replaced the entire throttle body with a new one from ford and it keeps doing the same thing. I don't want to keep buying electronic parts as they are not returnable. My truck is a 2005 Expedition with 72k miles on it
View 1 RepliesFord F-150 (2004-2008) :: CEL After Engine Failsafe Mode Message
I have a 2004 F-150 Lariat with a 5.4. (FYI-Have not had clockspring recall fixed yet)
124K miles. Vehicle has been operated in AZ and TX only until coming to Minot, ND 6 weeks ago.
3 days ago I got an "Engine Failsafe Mode" on startup. I shut the vehicle off immediately. Started it up again and the "Engine Failsafe Mode" message disappeared, but the engine light came on and has stayed on for the last 3 days. It seems to be running ok, maybe a little rough.
I ran the reset info on the dash screen and all systems read out OK. I have not run the truck over 40 mph since, and not on the highway, but it seems to accelerate without a lot of hesitation.
I've seen in other forums that this might be a dirty or faulty throttle body and/or the dealer may be able to re-flash with updates but this is old 2004 info from newer owners back then.
What am I looking at from a time/price angle when going to the Dealer for service? I don't want to replace a throttle body if it just needs to be cleaned and re-flashed because I'm ignorant.
Anything I should watch out for? I'm not a competent mechanic!
Ford F-150 (2004-2008) :: Truck Recently Started Sounding Like Trying To Shift Into 4X4 Mode While Driving - Gears Grinding
At a loss right now. My 2004 F150 4X4 and just recently started sounding like the truck is trying to shift into 4X4 mode while driving it. It stops if it's switched into 4X4. I have taken it to a local mechanic shop I use and they said it was the Actuators and they replaced those. I got it back and the same day the noise came back. Took it back and they have had it for another week and still unable to figure it out. I even took it to another shop that was highly recommended and they say to take it to a Ford dealership. I have read that some say it could be the vacuum operated hubs? Need to figure out what it was and had it fixed?
View 1 RepliesFord - Explorer :: 2004 V6 - Recurring Engine Failsafe Mode P2106
So my Explorer is a 2004 Eddie Bauer v-6 with about 93K miles, great condition, very clean and never had any issues. I've had it about 6yrs.
For maybe 3-4 years now the truck has seemingly randomly gone into Engine Failsafe Mode in the message center. I haven't noticed any pattern here as to when/why this occurs. The wrench icon lights up as well as the Service Engine Soon light. Sometimes I seem to notice a change in power/performance but often I don't. There are times when this happens every few days, and sometimes it goes weeks without occurring. Often it just goes out of Failsafe Mode after I've turned the truck off and restarted and seems fine again. For all of these years this has been a nuisance more than anything and so I assumed(hoped) it was just a sensor issue and nothing to be worried with.
A few days ago the truck actually shut off while driving...losing power, immediately after it kicked into Failsafe Mode while driving slowly down a straight road (no inclines or anything). Today it went into Failsafe mode, and it kept running, however the gas pedal did nothing...I couldn't accelerate at all though I still had power. Coasted to a stop. Turned truck off, started right up and the gas pedal worked fine. 15 minutes later same thing...this time when I coasted to a stop...I noticed that when I put truck in reverse I WAS able to back up using the gas pedal but couldn't go forward. Turned truck off, ran fine though still in Failsafe Mode...drove home where it sits now.
Don't really wanna drive it now though I need it as my only source of transportation. I did have the scan done on it at Autozone a month or so ago and got the P2106 "Throttle Actuator Control System--Forced Limited Power" reading...which of course means nothing to me...and the guys who worked there had no idea either. I had the oil changed at Midas yesterday where they checked fluids and all that good stuff...I mentioned it before hand and they said they looked at anything they could and couldn't find anything without running diagnostics on it...I didn't have them do this as it is quite costly and at that point I hadn't experienced the issue with losing acceleration/gas pedal functioning while driving down the road.
Ford F-150 (2004-2008) :: 2005 - Truck Starts To Sputter And Kick A Bit When Driving At Low Acceleration
I have a new to me 2005 F150 with 86,000 miles. When I am driving through town at a low acceleration or a constant speed at between 40 - 50 mph the truck starts to sputter and kick a bit. When I give it some gas the problem goes away. This gets worse when I pull my bass boat, and starts at around 30 mph. When I hook it up to a reader I get a P0316 code. Only code I get.
Also when I am driving through my neighborhood between 20 - 30 mph I get a noise that sounds like there is a plastic bag stuck under the truck. I have checked under the truck to see if the firewall is loose anywhere, but could not find anything. Other than those two issues the truck runs great. What these problems could be?
Ford F-150 (2004-2008) :: Truck Shut Down - Engine In Safe Mode?
I was driving down a road tonight and my entire truck shut down, and it said engine safe mode. I lost all power steering and gas, all I had were breaks and electronics. What does that mean?
View 1 RepliesFord F-150 (2004-2008) :: Just Rebuilt Trans Now No Speedo / Truck Goes Into Limp Mode
Just fully rebuilt transmissin 4r75 replaced all planet gears clutches etc. Now with it all back together the speedo does not work on truck goes into limp mode. I replaced the vss sensor an no luck
View 8 RepliesAccent MC (2006-11) :: Locked Into Failsafe Mode 3rd Gear
Problem started after an ignition coil went bad where '06 Accent w/ 45000 miles locks into 3rd gear failsafe mode. Changed coil and plugs, flushed transmission fluid and refilled with SPIII. Old fluid was very dirty but not full of metal bits. Car still goes into failsafe first time it reaches 3rd gear after initial startup. If you disconnect and reconnect battery after driving for 1-2 miles in 3rd gear the car works fine. Even after sitting for an hour and still slightly warm car works fine. If car gets cold again 2-3 hours later in winter you go into failsafe in first mile. Once again battery disconnect/reconnect puts it back to normal. I assume it is some type of sensor going bad and don't want to have a repair shop replacing good parts.
View 5 RepliesFord F-150 (2004-2008) :: 2005 Truck Going Into 4x4 Lo By Itself
I've got a 2005 F-150 (5.4 triton) with about 35k miles that I rarely use in 4x4 mode. The other day, after stopping to fill up with gas, the truck 4x4 Lo light was on after starting it. The dashboard switch was still in 2H mode as I never switched it. I first thought that the dashboard light might be in error, but when I began to pull out of the gas station. the truck was in fact in 4x4 Lo. I had forgotten how to cycle it back to 2H so I slowly drove about 3 miles home at 20 mph.
Once home, I re-read the tranny sync sequence and managed to get back to 4x2. I called the dealer who never heard of a truck getting into that Lo mode w/o activating the switch and suggested that I just monitor it. I read a number of forum threads discussing the IWE and solenoid problems, but all of those threads dealt with issues of not being able to get too 4x4 mode. My biggest concern is that I leave in a month for a 2000 mile trip, towing a cargo trailer and I'd hate to inadvertently switch into 4/4 when traveling 60 mpg on a highway.
Ford F-150 (2004-2008) :: 2005 - Vibration At 75 Kms Throughout The Whole Truck
I'm having an issue with my 2005 f150 xlt. Its been happening for almost near a month and still cant locate the issue .
It has a vibration at 75km throughout the whole truck. Ive tried multiple things done to it by a mechanic, such as having the tires balanced and the ujoints replaced. The problem still persisted and after attempting to test out to see if press/releasing the parking break (my mechani suggested trying that out), my driveshaft fell off.
Apparently the center bearing snapped and cant simply be replaced on the 05's. So i had to get a new driveshaft installed (used, both the 3 mechanics I've gone to say its in good condition).
Even after replacing the driveshaft the issue persists - however it seems a bit softer than it was (I am guessing the old driveshaft was worn from the vibration causing it to be worse). After that I took it to another shop to see if they could locate the issue. They did a driveline inspection and engine inspection too see if a misfire could be the cause.
Again, nothing was found. The only thing they were able to find was that the issue only happens under load and slightly occurs at 40 and 100km as well (although alot softer then the one at 75) and they say they cant find anything physically and it was a mystery to them.
Ford F-150 (2004-2008) :: 2005 - Truck Idles Around 600 RPM When Warm
I have an 05 150, 5.4l, My truck idles around 600 rpm when warm, I think that may be slightly low. Not sure what to check on.
View 1 RepliesFord F-150 (2004-2008) :: 2005 Truck Bucked And Cut Out When Accelerate
Well I have had a completely dependable truck until today. I was driving my truck on the way home, its an FX4 with only 33K miles on it that i have had since new. I went to accelerate to pass some cyclists (not a hard acceleration) and the vehicle cut off seemed like it kind of bucked a little as if it was shifting gears hard. I got a service light but what was weird was the gauges worked and the RPM still showed 1000. I did have power still though as the radio was on. The only thing that is currently wrong with the vehicle is the odometer gauge is out and needs to be replaced.
Anyway I shifted to neutral and restarted on the fly and than shifted back into drive and it drove the rest of the way home fine. After i got it to my neighborhood i ran it hard and it did not cut off again. I do not want this vehicle to cut out of me in town in the middle of traffic or while i am driving my 18 month old around and i get disabled with her in the truck. Slug of water maybe? I filled up on monday and still have around 3/4 of a tank of gas. Maybe short because of the gauge issue getting worse? I have the crazy door locks and beeps but nothing else has occurred. 05 F150 FX4 5.4 ....
Prius Plug-in 2012-15 :: Check Hybrid System Message While Driving On Freeway In EV Mode - Code P03CE
Yesterday while driving on the freeway in EV mode, my PIP (one of the first delivered to the states) flashed the "Check Hybrid System - Stop the vehicle in a safe place" message. I was near my house so I just went home. My SG2 showed code P0C3E, which is apparently an inverter over temperature code.
Took it to the dealer this morning and they just informed me that the car needs a new inverter, but no other details… "internal fault" is what he said.
While googling, i found this recall notice:
Green Car Congress: Toyota recalling about 701,000 Gen 3 Prius vehicles in US over software issue in inverter assembly
that doesn't talk specifically about the PIP and implies that it is a software problem, but goes on to say if the car is in a fault condition the inverter will be replaced. of course, it's possible that a software problem leads to hardware damage.
Ford F-150 (2004-2008) :: 2005 - Making Truck Extremely Loud?
what can i do to make my truck really lout? ive already cut 2 cats out and ran 2.25 strait pipes and its not even that loud would it hurt to cut the other 2 cats out??
View 10 RepliesFord F-150 (2004-2008) :: 2005 FX4 Truck Extremely Rough Idle
A week and a half ago I went out to my truck to go somewhere and I got about 2 blocks away and the truck started running really rough and had a big lack of power, so I turned around and scanned it with my code reader and the codes I got were p2271, p2196, p0303, p0012, p2197, and p2272. since then I've changed all the spark plugs, boots, swapped all the coils and injectors from a great running truck, fuel filter, and the bank 1 upstream O2 sensor.
the other thing that came to mind that could of caused the problem is that a few days before the problem started. I jump started a co-workers car and he hooked the cables up backwards on his car. Could this be the cause of the problems I'm having.
The truck is an 05 F150 FX4 5.4 with 180,000 miles on it.
Ford F-150 (2004-2008) :: 2006 - Truck Cuts Off In Seconds After Driving
I drive a 2006 Lincoln Mark LT and recently had a new heater core installed, but now when I try to drive it, it cuts off on me once I get out of the driveway. It starts back up fine, but then cuts again seconds after I try to drive. When I start the car it idles fine. I could have it idling for 10 minutes plus and have no issues, but once I shift it into gear and begin to back out of the drive way it shuts down again.
View 6 RepliesFord F-150 (2004-2008) :: 2005 - Truck Shuttering And Bucking Along With Loss Of Power
I have had the check engine light on for a while now with the truck shuttering and bucking along with loss of power. Feels like there is something holding back the power. Just a couple days ago I was driving on the freeway and all of a sudden it felt like I was in neutral, tried to accelerate but the engine revved but wouldn't go anywhere, I clicked the overdrive on and it went into gear and I was able to drive home. Now every time I drive it, it goes a block or two in drive then again feels like neutral, put in overdrive and it goes into gear. I just put in new ignition coils.
View 9 RepliesFord F-150 (2004-2008) :: 2005 FX4 Truck Gear Shift Stuck In Park
My truck gear shift is stuck in Park (console type). I have been reading threads that discuss potential causes such as blown fuses, bad brake switch, bad brake shift interlock actuator, and even ignition switch. All fuses are okay. Before I try to get into all the other possibilities, I have a question around what the local auto parts worker suggested. He said that there is a small plastic piece that may have slipped down interfering with gear movement. This could make sense, especially since the white manual release lever doesn't seem to be moving.
View 14 RepliesFord F-150 (2004-2008) :: 2005 Truck At Partial Throttle Will Shake When Going Up Slight Incline
.Here is a run down of my truck 05 5.4L Screw has 130K on it. Sometime when going up a slight incline the truck at partial throttle will shake very very little. if I put my foot into it the shake goes away and the truck response just fine. It only does this when going uphill on the freeway and on the streets here in Dallas that have slight inclines.
The truck is not throwing any codes nor does it stall at lights. Starts right up in the morning and runs good. Nothing done to the truck except I have an Edge programmer and Magnaflow exhaust. I have pulled the programmer off and returned the truck to stock and it still does the same thing.
I bought the truck used in 07 had 40K miles on it. I'm thinking spark plugs or maybe a coil is going bad. But this doesn't happen all the time just here and there.
Ford F-150 (2004-2008) :: 2005 - Changing Rim And Tire Size To 28565r20 To Level The Truck?
I have read many pages here on issue of leveling trucks.What concerns me most is the pics I see of the drive axles angles.
My question is if my stock 2005 runs a 265/70r17 tire and I level it with a 2 to 2.5" kit and change my rim and tire size to 28565r20 will this keep angles more level..