Ford F-150 (2004-2008) :: 2005 - Running Rough And Misfiring Quite Frequently
Mar 26, 2011
My 05 was running rough and misfiring quite frequently. After much deliberation, I took it in for a diagnostic hookup. The dealer said my driver side cat was clogged. Lucky for me, I was just under the warranty period(79673 miles). I have had it replaced and I can feel a noticeable difference in the way it runs. Could a clogged cat have made it run that poorly or am is it just in my head that it is running alot better?
View 7 Replies
Advertisement
i have a 2005 f150 4x4 5.4 3 valve. it ides good but when it is in on it splutters, and also feels like dead cylinders in passenger gear. i checked the codes the other day and i had a cylinder 5 misfire. so i cleared it and today checked again and had running lean bank one and cylinder 8 misfire, then checked one more time and had cylinder 7 misfire. I am sure it is a bad coil but how do I know which one?
View 2 Replies
I changed the timing chain, phasers, tensioners, guides, and cam sensors and solenoids about 30k miles ago. Truck now has 170k miles. This past weekend engine started running so rough, it had the whole front end shaking. Threw 8 codes..1 bank..lean, bank 2 rich, timing retarded, cylinder G and F misfire, and more codes. It seems to have jumped timing pretty bad.
View 1 Replies
I recently bought a 05 f150 with 5.4 3v and 195k miles needing some work. Ran great, just had a code for timing over retarded. Originally it had a cracked timing cover, so i took it off to replace and found broken guides and bad tensioners on timing. I installed new guides, chains, and tensioners, and cleaned phasers, and put back together only to find it ran terrible and had a phaser rattle. I then went in and installed phaser locks, which took care rattle but not the running issues. I can not figure it out.
ISSUES: My issues almost mirror what is said in this thread here, but this issue was never solved. [URL] ....
My issue is when started cold it starts right up, idles ok, runs ok, although a bit sluggish. Once its warm it stalls at idle, shudders when giving throttle in overdrive, and if you kick it down it will continually backfire, and slowly accelerate... it kicks down but acts like its only getting 1/8 throttle, just kind of hangs at the same rpm and slowly climbs in rpm. Sometimes it wont backfire as much, and sometimes the check engine light flashes. After it stalls at idle and you start it back up it sounds like it shudders/backfires for a split second then starts.
It is throwing many engine codes, but most are from the phaser locks. Throws code for timing over advanced on each bank (phaser locks lock them fully advanced), cam timing codes for each bank, and then a code that doesn't have to do with the timing, P2106. I am going to run some live diagnostics on it today and report back but I am fully at a loss.
View 5 Replies
Had a miss in the #5 cylinder on a 2005 F-150 5.4 Triton. Had it hooked up to see which code was given and the tech said that #5 was the culprit. Taking no chances, I purchased a new plug and coil pack. I installed them and it ran great until I got up to around 70mph and then it started dong the same thing it was doing earlier. I took it back to the place that checked the codes and it came back as the #5 cylinder misfiring again. I am not sure how this is possible after replacing the plug and coil pack. Is there some way that the plug that fires just ahead of #5 is fouled out and causing the #5 cylinder to get too much fuel transferred to that cylinder? Or is there a possible short somewhere causing that cylinder to misfire and ruin the coil pack? I am stumped on this for the moment anyway.
View 8 Replies
I just changed the plugs in my 05 stx 4x4 4.6L. Truck was running fine, never a problem but it has 105k so I figured id change them. #4 was the only one that gave me a little problem (besides being so tight). The coil and spring pulled off the boot, and I had to get a pair of pliers and get the boot off the plug.
I simply slid the spring back through the boot and replaced it once I had changed the plug. Other than that they all came out easily. I replaced with motorcraft plugs, and #5 did have what looked like some oil down on the threads when I pulled it out, but not sure if that's a big deal or not
Any way, I am torn between ordering new boots and changing them out, or just biting the bullet and getting 8 new coils with new boots attached. Truck runs fine, but does the usual buck/jerk under a load in overdrive now (never once did it before)...
View 3 Replies
I recently purchased a Ford pickup. I bought a 2004 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 200,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run good when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come to on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
View 14 Replies
My ranger just started running very rough. Like misfiring, but I think it may be the fuel pump. It starts and drives...but it surges then drives normal, as if fuel is being fed, then starved, then force fed etc. My father asked if I had trouble starting it and to be honest in the last 6 months it was a little harder to start on several occasions. On a few occasions it required more cranking. But that was only a few times.
I tried putting in a fuel injector cleaner and 93 octane gas but it is still running even rougher now. I changed out the fuel filter under the rail about a year ago (maybe 8000 miles ago at most). My father thinks the fuel pump is shot and he laughed because his went on his expedition and he said it is inside the fuel tank and there is no way to get at it without dropping the tank. Is that true? 2002 ranger xl 4cyl
View 7 Replies
I have a 2000 ford explorer. 4x4 v6. One day i started it up and it was running rough. It had real sluggish power. Then the check engine light came on. I hooked it up to the code machine. The only readout was number 3 misfired. I replaced the plug and all was fine. A few months it happend again. I replaced it again and it was fine. Well it just happened again. I replaced it again. It ran good to work but on the way back no good. Light came on again. Hooked up the machine it read number 4 misfired and number 2 bank lean. So I replaced number 4. It still runs like shit rough idle and no power. Give it gas it dogs out but then it'll kick in if i get on it. Thinking it maybe a vaccum leak or intake leak or o-rings.
View 4 Replies
So Friday before last my ex laid down on me while i was headed to work. So I parked it in a walmart parking lot and caught a ride to work with a friend then had it towed home that evening. Problem i was having is it started running really bad, miss firing, smoking, and sounding real rough, but I wasn't getting any trouble codes. So after both uvch's, icp, ipr, icp pigtail, checking fuel for water contamination and pulling my hair out, i decided to check the oil and found it to be 4 quarts low. Talk about feel like a knuckle head.... While it was down it did receive a new water pump, a diesel site 203* thermostat, new billet thermostat housing, Gooch's Radiator Flush Procedure, and some fresh rotella etc.
View 5 Replies
History: Truck was running okay but acted like a coil was bad when under load. I changed out all the plugs with Motorcraft and put on Summit racing COPs.
After the plug and cop change the truck will run rough after it is warmed up. I changed back to the old COPs and it runs the same.
First I replaced the MAF sensor after finding many posts on here about it. No change.
I read a bunch of posts on oil causing the problem so I used 10-30w and nothing changed.
I searched for a vacuum leak with carb cleaner and couldn't find one. I removed, cleaned and reinstalled the throttle body.
When I did the plug change I disconnected the PCM without disconnecting the battery. Would this cause this type of problem?
I think this is about all the stuff I found to try in the threads that came up through searching.
View 13 Replies
My f-150 has an intermittent rough idle and consistently runs rough when you accelerate quickly. Vehicle is not throwing any codes?
View 3 Replies
I have a Ford F150 XLT. I have 67000 miles on it and the other night it just started running rough out of no where near idle. Once you got over 20mph the rough running would go away. I took it to get an engine change and engine flushed but it came back. It doesnt always run rough near idle or below 20mph. The Ford dealer says my engine has only 22 psi oil pressure near hot idle and cant engage the VCT phazers and they want to replace the whole engine.
View 1 Replies
I just completed a successful second spark plug change, using Motorcraft SP515 plugs just like last time. After reconnecting battery and starting engine, it ran poorly throughout a short road test. Felt like it was skipping. Checked under the hood and found that the #2 fuel injector was disconnected, so I reconnected the injector.
I took another short road trip and it still ran poorly as if skipping. So, this time I disconnected the battery for several minutes while removing the #2 plug thinking I may possibly have fouled the plug by the injector not being connected. I also checked all of the other injector and coil connections. Reconnected battery and took another short trip. It still runs poorly. No codes yet.
View 14 Replies
I have 07 sscrew with 5.4. 93,000 miles. At start up truck runs perfect. After 20-30 minutes of running motor will start to start running rough at low rpm. Diesel sound. I can rev up and motor clears up and idles fine. Should I replace VCT solenoids? Or phasers? Or both at one time??
View 14 Replies
I just bought a 2007 F150 XLT with a Triton 5.4 with 80,000 miles on it. My problem is this, the engine seems to run ok ( a bit rough) until it gets up to running temp and I have driven about 10- 20 miles then most of the time, it starts to act up.
When I am driving it is fine, but when I slow down and come to an idle about 500rpms, it sometimes runs very rough, sounds like a diesel and shakes violently. It feels like it is doing damage. Sometimes it stalls. If I rev it back up immediately it will smooth out.
In speaking to some friends they've suggested things from plugged oil channels, (affecting the cam phasers? All the way to it needing new chains, phasers and guides. I don't want to spend a ton of money doing an improper service repair only to have the issue show up later . But there seems to be a lot of different answers to the same problem. Is the dealer going to be able to diagnose something like this fairly well? Or should I try to narrow it down a bit first?
View 2 Replies
the F150 of my brother has the follow diseases:rough running ticking noises, low mileage per gallone, blue smoke out of exhaust after start, i have ordered the cam phaser, hope, that will be the reason. But today, my brother means, i have to do a test drive, because the truck has no power. and really, feels like missing of one or two cylinders. Very bad performance. Is it possible, that the reason are the phasers?
View 4 Replies
I just had my 04 5.4l engine rebuilt. Ive driven it about 500 mi and it started running rough at a stoplight. I tapped the accelerator and it started running good again but service engine light came on. I pulled the codes and they were P0022, PO345, P0340,and P0430. It has done this several times now. Everything was replaced including the phasers, except for the camshaft sensors. Could they cause this problem?
View 3 Replies
On my way into work this morning, my 06 with the 5.4 started running very rough/shaking at low rpms. I could kick it out of overdrive and it would smooth out and seemingly be fine at higher rpms.
This worked out for a couple of miles until the truck just died on me completely. The Edge is showing po351, 352, 353......358 codes. Ignition coil Primary/Secondary circuit fault on every cylinder.
I'm thinking its unlikely that every coil failed simultaneously....computer? When I try to start the truck, it will try to hit on a cylinder or two, but will not run.
View 3 Replies
I have a 2004 Ford F150 with 149,000 miles I have recently put 5,000$ In the motor that is a 5.4 V8 before it would shake and make a terrible noise got a brand new engine from Ford put in by a ford mechanic but now my rear end squeaks like crazy and it is all the time more so when going up or down a hill or when it's shifting more or less or going over a ruff surface that's been going on awhile and was told I needed a new rear end by the same ford mechanic and wanted 1,000 to fix it!
But also said the whining noise that is coming from the front was the transmission and that I shouldn't worry about it to drive it till it goes out but it's a terrible whining noise that you only hear it when your in gear not in park or neural the truck sounds good what causes this whining noise?? Not done yet but recently the front driver side around the wheel has also gotten a squeak mostly when in low speeds and turning to the left! What to do? I'm already replacing the motor! Hopefully these are some easy fixes! I've done some research and the whining from the front that I was told to be the transmission doesn't seem to be that I would think more along the lines of pulley or alt!
View 2 Replies
My 1999 lexus rx300 first threw a P1135 following a P0125, I tested the sensor and it was open at the heater circuit then then I was waiting the new part in the mail and during that time it kept running rough and then it threw a P0300, P0301, P0305, P0303. I was thinking that the PCM cannot monitor A/F ratio without the sensor so maybe the injector base pulse width was good enough. The misfire is are on bank 1, same as the bank 1 A/F sensor.
View 3 Replies
