Ford F-150 (2004-2008) :: 2005 - Rough Idle - Power Loss?
Jan 29, 2014
my f150 running right so i can enjoy it like everyone else does. I have a 2005 Ford f150 with a 5.4 auto.
It has a rough idle(shakes the truck), very little power, and poor gas mileage. Randomly It will throw a code for misfire on 1 and/or 3 on start up only. It does seem to perform better within the first few of starting but dies right off after that. In fact i got stuck in the snow the other day and it could barely break the tires loose to try and get it out (almost put in 4low cause i didn't want to hurt the trans). I have replaced:
Cats
Fuel pump
Plugs (motorcraft)
Random Coils
Did the timing chains and phasers
MAF
All new injectors
Intake gasket
Was at my mechanics and had a scanner on it and at idle the 1-4 cylinders are all show a negative cylinder contribution. But when you rev it up they all go to 0 across the board. Was kind of thinking about the Variable Timing solenoid.
View 1 Replies
Advertisement
I have a 2005 F-150XLT with the Triton 5.4L. The other day while driving on side roads (Paved, not back roads) I noticed my CEL on and it was blinking. There was a very rough idle as well as a big loss of power. When I pressed the gas pedal it was sluggish to say the least. I have yet to get a computer on it, since I had to order one. There is also a light gas smell, only smells near the rear of the truck. From what I am guessing, I think it is either a spark plur or a coil over pack, Truck has about 56K on it.
View 1 Replies
2005 250 5-speed total oil pressure loss ... At 110k mechanic diagnosed failing phasers from noise, rough idle, loss of power under 1k rpm. (Crew cab long box xl bought new for $25k)(first 100k were from carpenters (hard miles) so this truck is barebones and usefulness is much higher than cash value). Truck has 146k
All symptoms typically disappear over 1k rpm so I have limited idle time and manipulated engine speed to try and maintain 1000-1200 and all has been well for past 36k miles. Today noise (valve clatter?) persisted at all rpm and during a scramble to get off the highway all oil pressure was lost (I'm aware that pressure gauge on dash is not 100% reliable). After total pressure loss I cut engine and called tow truck. Out of curiosity, I actuated ignition and motor cranked maybe two rotations, and then appeared seized. After about 45 min waiting for tow I went back to disengage 4wd and take my rifles and skis out of truck. At this time I actuated ignition again and engine fired and ran as it had for past 36k miles. I drove about one mile constantly watching oil pressure gauge, then noise returned followed by instant drop from normal to 0 pressure (dash gauge) I immediately shut of engine.
I am a mechanical engineer, but not a mechanic. I am familiar with the cam phaser system and I understand that their operation is directly related to oil pressure. Today's temp was under 0'F. I have a very skilled mechanic who works for around 30-40% of cost of licensed shop and I know his skills to be on par.
View 4 Replies
I have a 2004 Ford F250 with 174,000 miles the truck has a slight miss a rough idle one hot or pulling I have 2 codes nut no light when I go into the ford oem feature in my scanner a PO 272 and a PO404 .. Where to start?
View 4 Replies
I have a 2005 5.4l f150. 105,000 miles. Recently While on a trip I experienced rough idle and stalling at idle. I drove it home 2hrs. The ride home was challenging. Poor acceleration, rough idle. Took it to the dealer and was told I needed plugs and I was 5qts low on oil! Not sure where the oil went. It hasn't been leaking and never seemed to burn oil in the past. They did the tune up. Picked up the truck. It ran fine while cold. Upon warming up it ran rough at idle and stalled just like it did before. Took it back, they said "you need a new engine. Upon warming the oil pressure drops indicating internal engine damage". I took it to a local guy he says replacing the cam phasers might fix it. What's the consensus, should I try the cam phasers? Look for some other potential problem or trust the dealer? (They did refund me for the tune up)...
View 14 Replies
2005 f-150 4.6l v8 rough idle only when truck is to normal operating temp. I have run several gas system cleaners through the truck. I replaced the air filter, the fuel filter and the spark plugs. I am only getting 14to 15 mpg mostly highway. No DTC's are showing up. The truck only has 50,000 miles.
View 6 Replies
I just purchased my first F150, 4.6L V8, 55,600 Miles. It intermittently has a rough idle and only seems to be when the engine is hot. I've had engine and tranny mechanics look it. The spark plugs have been inspected and are within an acceptable range. The throttle body has been cleaned. There are no trouble codes of any kind. What I can check next?
View 13 Replies
A week and a half ago I went out to my truck to go somewhere and I got about 2 blocks away and the truck started running really rough and had a big lack of power, so I turned around and scanned it with my code reader and the codes I got were p2271, p2196, p0303, p0012, p2197, and p2272. since then I've changed all the spark plugs, boots, swapped all the coils and injectors from a great running truck, fuel filter, and the bank 1 upstream O2 sensor.
the other thing that came to mind that could of caused the problem is that a few days before the problem started. I jump started a co-workers car and he hooked the cables up backwards on his car. Could this be the cause of the problems I'm having.
The truck is an 05 F150 FX4 5.4 with 180,000 miles on it.
View 9 Replies
I have a 05 fx4 5.4L with 85k on it. It has started idling rough when i come to a stop light or slow down to 10 mph or less. It only does it once in a while. There doesn't seem to be any real pattern. The motor shakes until you rev it up and then it goes away.
I have cleaned the maf, put in new air filter and fuel filter. And put in a new battery. Would a coil act like that? Maybe plugs? Or a vacuum leak?
View 14 Replies
I have a 2005 f150 5.4 3 valve with the p0012 code the truck runs good has a rough idle not sure if it is worth changing the vct or not the truck has 190000 miles....
View 1 Replies
Getting these codes what they mean or need to do ..to get rid of them...p0022, p0171, p0174, p0183, p0340, p0300, p0316, p2006 did timing n plugs fuel filter n gas filter getting very bad gas mileage it runs good but here a ticking in motor at idle and more as u accelerate, running rough....
View 7 Replies
i have a 2005 expedition with the 5.4 and 100k miles. Rescently it began to missfire badly and lost almost all power to the point where it nearly dies. I have seveal codes that are baffeling me. Bank 1 is rich bank 2 is lean(this may be the other way around, p0300(multiple cyl missfire) and then 4 individual cyl missfire codes. I changed all of the spark plugs with factory motocraft ones from ford as the old ones were shot. Seems to miss just as badly as before and is no where near driveable. What would cause one bank to be rich and one bank lean? I ohmed all of the coils when I had them out and they all are very close to each other with no odd ball ohm readings so I believe they are all ok. Any sugestions as to where to check next?
View 3 Replies
2005 F150, 5.4 motor. Truck would loose power and no throttle response. Shutting off and restarting, ran fine. No codes showing. Cleaned throttle body and plate, reassembled. Key left on for 20 minutes. Tried to start vehicle. Making a clicking sound, dash lights flashing on and off when hear clicking sound when trying to start vehicle. when key turned to on position, dash lights go off except check engine light. When checked, no codes shown.
View 3 Replies
I have had the check engine light on for a while now with the truck shuttering and bucking along with loss of power. Feels like there is something holding back the power. Just a couple days ago I was driving on the freeway and all of a sudden it felt like I was in neutral, tried to accelerate but the engine revved but wouldn't go anywhere, I clicked the overdrive on and it went into gear and I was able to drive home. Now every time I drive it, it goes a block or two in drive then again feels like neutral, put in overdrive and it goes into gear. I just put in new ignition coils.
View 9 Replies
2005 f150 Lariat 4x4 5.4
Had phasers, tensioners, chains, guides, and sensors replaced. After driving the truck, it started to get a rough idle at low speeds, primarily in reverse. Changed both vct solenoids with no results. Started to get p0022 code. Changed the oil with motorcraft filter and 5w-20 twice after the work had been done, thinking it might need it. Vct's were a little varnished, but not too bad.
After a couple days of light driving, got a misfire on #3. Replaced the coil and it hasn't been back since. I am stumped at this point.
The computer show the timing to be at +13 when sitting stopped and in drive. It fluctuates a little, but not much. When the truck goes into a rough idle. The rpm's fluctuate wildly. It seems to be happening more frequently, the more I drive it.
View 3 Replies
I just locked out the cam phasers on a 2005 f150 with a 5.4. It now idles pretty rough. If I blip the throttle the revs will rise and then drop again, and it barely catches in time to prevent a stall. If I continue to tease it this way I can usually get it to stall. I'm getting no CELs or anything, but I intermittently will get a P035x code (it seemed to rove. I've gotten cylinder 1, 4, 6, but not consistently.). I have chased those around by swapping coils, checking/cleaning the connectors, etc.
I am kind of thinking that these codes are a symptom of my idle issues, and not the actual problem. What could I have done wrong? Could it be a vac issue? I had basically the entire ECU harness and all the vac lines disconnected to do the job, but as far as I can tell everything has been reconnected to the correct locations. I did have an SCT tune done to remove the phasers in the ECU. I installed it and still have the issue, so for now I am on the stock tune just to eliminate any variables.
Could my tune be the issue? Is this how you would expect the engine to behave with locked out phasers and no corresponding ECU tune?
View 1 Replies
2004 Accent 1.6L
Changed the timing belt and water pump this past weekend. I made sure the timing marks aligned before I put the belts on. They were still aligned after turning the engine by hand and still aligned after taking the car out for a test drive. I did not notice rough idle when I started the engine in the garage nor did I notice a rough idle during the test drive.
A few days later I am now noticing the car will idle roughly when I come to a stop. The idle will get rough enough to gently shake the car. No engine light and no unusual noise from the engine.
I am going to check the timing marks again tonight. I suspect the belt may actually be off by one tooth. I have driven over 100 miles since changing the belt so I don't believe it is off anymore than one tooth or else I presume I'd probably have already broken down or been hearing unusual noises.
Furthermore, I do not seem to have any loss in power. I still have good acceleration and no roughness unless at idle engine speed. I do, however, run rough at higher speeds (75+ mph) on the highway, but this was present before the timing belt change. Unfortunately the car does not have an RPM gauge.
Having said all of this, are there any other possible reasons why I might be idling rough now?
View 4 Replies
I posted awhile back about a loss of power and hard shifting in the transmission. I thought I had it fixed, well I kind of did...... Replaced the IWE that had locked in solid. I replaced both, added some transmission fluid, new front brakes, and a new belt back in July/August. Truck was fine for a few thousand......
Well it's back. Now I have a noticeable whine in the cab. I haven't pin pointed it yet. It is only audible when the truck is running from 35-50 mph. It is not RPM dependent, it doesn't change when I take it in or out of four wheel drive. It isn't there when the truck isn't moving.
The truck has 61,000 on it. I bought it with 35,000 on it because I wanted a vehicle that wouldn't nickel and dime me. Something I could climb in and not worry about making home.
Well here I am less than 30,000 miles later and I have had issues with the fuel controller under the bed, brake calipers sticking, IWE's, new shocks, broken front coil spring, recall for the airbag, tie rods, ball joints, power window regulator, and now what appears to be a transmission.
I come from a long line of "FORD" guys, but I am seriously considering something else. This 04-08 model has to be one of the worst pickups ever built by ford.
Are the newer ones any better? Other than routine maintenance a vehicle shouldn't have to be touched before 61,000.
View 4 Replies
My 07 F150 has no power. I changed the timing chain, cam phasers, spark plugs and all 8 coils and still no power. Rough idle and bogs on acceleration.
View 3 Replies
Have an 06 F150 5.4 3v with no power. spark knock. rough idle. wants to die while driving, and random misfire code. Have replaced fuel pump, filter, coils and plugs. What to check next? Already thought of EGR - it doesn't have one.
View 4 Replies
Dad has a 01 one ton with the 7.3 and isn't real tech savvy so I'm posting for him. He is the original owner and has been complaining recently about the lack of power. Particularly the upper end. He is having to downshift way more often and where he used to not have to. And we've both noticed a very noticeable shake at idle. Not a vibration but a true shake. He changes the oil every 5000 on the dot and I've gone and changed the air and fuel filter and ran hose and see foam and royal purple injector cleaner through it with no results. Truck is all stock with 225000 on it.
View 7 Replies
