I have a 2005 f150 5.4 3 valve with the p0012 code the truck runs good has a rough idle not sure if it is worth changing the vct or not the truck has 190000 miles....
View 1 Replies5.4 3v. my last few weeks have not made me a fan. Here are the details:
I bought a 2008 F150 XL 5.4 3v with a cam phaser knock. Have done other timing jobs in past with no trouble so I was not too afraid to tackle this one. famous last words...opened the motor (shout out to the passenger side valve cover and its designer here) and found semi damaged roller follower on driver side. Worn cam lobe on the corresponding lobe and a loose chain on passenger side. proceeded to :
Change all timing components: phasers, chains, tensioners crank sprocket, all applicable bolts and BOTH cams as well as all lash adjusters and roller followers. most looked fine in fact all really did with a bit of wear on a few roller followers but only one bad one. engine didn't look to bad pretty clean.
Double and triple checked my timing chains and it was spot on. dark link on spot on crank, two dark links on the L and R dead on. put it back together. oh yes, changed all plugs with motorcraft ones, didn't even break one. did not change vct solenoids because I falsely assumed I could change the later easily if needed. they looked ok. screens intact etc... silly me for not realizing how kind Ford was in 2007 and later to necessitate removal of valve cover. I was reading a previous one on the how tos and assumed later models would be the same since it was the same sensor...
Cranked truck ran great. I mean perfect. sounded perfect. ran like a scalded cat. till it got to hot idle then it started doing its thing. rattle shake till you revved it. ran fine just wouldn't hot idle fine especially in reverse or under slight load. replaced driver side vct since ford only had one and I started on the easy side ordered the other one waiting for it. seemed to improve dramatically meanwhile I am driving this truck to test it. I drove it to work 50 miles each way and it ran great.
After a few trips it popped the P0420 light, seemed to run ok, cleared it watched it wouldn't come back. O2 sensor did seem to imply a bad cat on bank 1 since it seemed sensor two was mimicking sensor one and not staying stead like the other bank. still ran fine,
So I decided to check back pressure on the cat. I pulled sensor one out of bank one (really a joyously tight squeeze in there) hooked up my gauge and got 0 back pressure. revved it and all nothing. hooked sensor back up pulled truck out of shop and it commenced to running like crap. I mean bad. running worse than before I got it. Popping P0012 code continuously, and tons of misfire codes associated with bank 1 ..cyl 3 etc.. I tried swapping coils, pulled coils and checked spark with a tester and firing away looks like tons of good spark.
Now the weird part is : looks like bank one is dead. I can unhook any coil pack and/or injector and it runs the same and sounds like it is missing. if I unhook one off of bank 2 it almost dies or does. so bank 2 seems to be running fine. it will start and run but sounds like it missing sets flashing check engine light and backfires and stalls like crazy. I even second guessed my pressure gauge and unhooked exhaust manifold from pipe and it sounds even prettier when it backfires out of there but no change. I pulled cam sensors and cleaned it again and even tried swapping them since they looked identical but no change so I put them back.
Now I can only surmise that I am out of time somehow? or I have a gremlin perhaps? I like working on cars (usually) but this one is getting old. how do I verify what is wrong. if it is timing related how do I verify that now definitively once my marks moved I really cant figure out how to tell if it is in time? Since it has all new parts and they all ran beautifully till now. could it possibly be the vct solenoid doing all this? I plan on changing it when it comes in but surely it cant cause this many problems.. I unhooked it no change, and it does it at a cold idle and any rpm. really runs worse at idle but bad at any rpm.
2005 f150 Lariat 4x4 5.4
Had phasers, tensioners, chains, guides, and sensors replaced. After driving the truck, it started to get a rough idle at low speeds, primarily in reverse. Changed both vct solenoids with no results. Started to get p0022 code. Changed the oil with motorcraft filter and 5w-20 twice after the work had been done, thinking it might need it. Vct's were a little varnished, but not too bad.
After a couple days of light driving, got a misfire on #3. Replaced the coil and it hasn't been back since. I am stumped at this point.
The computer show the timing to be at +13 when sitting stopped and in drive. It fluctuates a little, but not much. When the truck goes into a rough idle. The rpm's fluctuate wildly. It seems to be happening more frequently, the more I drive it.
I have a 2004 F-150 FX4 and I am getting Code P0012 on an OBD II code reader. This is saying that the cam timing is over retarded. What is the best way to fix this?
View 5 Replies2008 F150 5.4L .. The truck lost all power the other day driving and barely made it to work. On the ride home it was still running horribly, like it just fell on its face. the check engine light came on. Went to autozone and put HEAT in the gas tank cuz the night before it was at quarter tank and temp went from warm to freezing(thought maybe condensation in tank).. Truck ran a lot better( not perfect). Drove around that day and it was fine. Pulled down the driveway and CE light shut off. Ran the code anyways and it was P0012..
Talked to a few mechanics and they said try replacing the Camshaft position sensors..did so and it ran worse. the truck hardly would idle or rev and shook violently..i shut it down right away. Then it threw 9 codes..Cam shaft position- over retarded timing bank 1(P0012), misfire cyl2, misfire cyl3, misfire cyl 4, random misfire, cam sensor bank 1, three of them were repeated codes..
I replaced the sensors back to stock and cleared the codes. the truck is running like it was in the beginning of the problem..No vilant shaking but falling right on its face at idle and any rpm..not drivable. Would rather do the work myself. very capable except for replacing camshaft phasers which i have heard could be the issue..Could it by the VCT seliniod, EGR valve, plugs, wires...Did just change the oil a week ago and cleaned and reoiled air filter.
I have a 2005 5.4l f150. 105,000 miles. Recently While on a trip I experienced rough idle and stalling at idle. I drove it home 2hrs. The ride home was challenging. Poor acceleration, rough idle. Took it to the dealer and was told I needed plugs and I was 5qts low on oil! Not sure where the oil went. It hasn't been leaking and never seemed to burn oil in the past. They did the tune up. Picked up the truck. It ran fine while cold. Upon warming up it ran rough at idle and stalled just like it did before. Took it back, they said "you need a new engine. Upon warming the oil pressure drops indicating internal engine damage". I took it to a local guy he says replacing the cam phasers might fix it. What's the consensus, should I try the cam phasers? Look for some other potential problem or trust the dealer? (They did refund me for the tune up)...
View 14 Replies2005 f-150 4.6l v8 rough idle only when truck is to normal operating temp. I have run several gas system cleaners through the truck. I replaced the air filter, the fuel filter and the spark plugs. I am only getting 14to 15 mpg mostly highway. No DTC's are showing up. The truck only has 50,000 miles.
View 6 RepliesJust did the timing chain, phasers, oil pump and lash adjusters on my 05 5.4 s-crew. Always had a bit of a rough idle but now it's worse. If the truck idles for an extended period it sets a p0300. Just off idle the misfire is gone. It does seem a touch down on power but otherwise runs great. I did have the plugs out during the work. I cleaned them, applied anti seize and re installed. The previous owner had the plugs and COPs changed 10k miles ago. Plugs are motorcraft and coils are aftermarket.
I monitored with oreillys crappy scan tool and the miss only happens at idle. It is not a dead miss; unplugging COP on each cylinder still makes it worse.
Truck idles warm at like 570 rpm and if I hold my foot on the pedal to raise rpm a bit miss goes away.
Each cylinder is logging misfire counts with no rhyme or reason. The only thing odd during the timing job was 4 spark plugs were partially loose.
I'm sure the timing is correct; I used the OTC crank tool and for timing kit. Truck has 150k, front 02s are fairly new...
So I bought a 2006 F150 stx reg cab with the 4.6l motor with 90k miles on it a few weeks ago. It was in really good condition and I couldn't pass the deal up. All in all, I love this truck. However at idle the truck is a bit rough. No check engine light, but a bit rough non the less. So I hooked up my obd2 torque app and I see I have anywhere between 6 and 60 total counted misfires, but none detected by individual cylinder. So I ran a scan and have a B1360 code without the CEL on. So I changed the plugs and coil packs and cleaned the k&n filer (non cold air filter, just a replacement k&n) and I still have all the symptoms and the b136p code. So I Google the b1360 code and there's very little on it. Basically says open circuit ignition.
View 1 RepliesI just purchased my first F150, 4.6L V8, 55,600 Miles. It intermittently has a rough idle and only seems to be when the engine is hot. I've had engine and tranny mechanics look it. The spark plugs have been inspected and are within an acceptable range. The throttle body has been cleaned. There are no trouble codes of any kind. What I can check next?
View 13 RepliesA week and a half ago I went out to my truck to go somewhere and I got about 2 blocks away and the truck started running really rough and had a big lack of power, so I turned around and scanned it with my code reader and the codes I got were p2271, p2196, p0303, p0012, p2197, and p2272. since then I've changed all the spark plugs, boots, swapped all the coils and injectors from a great running truck, fuel filter, and the bank 1 upstream O2 sensor.
the other thing that came to mind that could of caused the problem is that a few days before the problem started. I jump started a co-workers car and he hooked the cables up backwards on his car. Could this be the cause of the problems I'm having.
The truck is an 05 F150 FX4 5.4 with 180,000 miles on it.
I have a 05 fx4 5.4L with 85k on it. It has started idling rough when i come to a stop light or slow down to 10 mph or less. It only does it once in a while. There doesn't seem to be any real pattern. The motor shakes until you rev it up and then it goes away.
I have cleaned the maf, put in new air filter and fuel filter. And put in a new battery. Would a coil act like that? Maybe plugs? Or a vacuum leak?
my f150 running right so i can enjoy it like everyone else does. I have a 2005 Ford f150 with a 5.4 auto.
It has a rough idle(shakes the truck), very little power, and poor gas mileage. Randomly It will throw a code for misfire on 1 and/or 3 on start up only. It does seem to perform better within the first few of starting but dies right off after that. In fact i got stuck in the snow the other day and it could barely break the tires loose to try and get it out (almost put in 4low cause i didn't want to hurt the trans). I have replaced:
Cats
Fuel pump
Plugs (motorcraft)
Random Coils
Did the timing chains and phasers
MAF
All new injectors
Intake gasket
Was at my mechanics and had a scanner on it and at idle the 1-4 cylinders are all show a negative cylinder contribution. But when you rev it up they all go to 0 across the board. Was kind of thinking about the Variable Timing solenoid.
I have a 2005 F-150XLT with the Triton 5.4L. The other day while driving on side roads (Paved, not back roads) I noticed my CEL on and it was blinking. There was a very rough idle as well as a big loss of power. When I pressed the gas pedal it was sluggish to say the least. I have yet to get a computer on it, since I had to order one. There is also a light gas smell, only smells near the rear of the truck. From what I am guessing, I think it is either a spark plur or a coil over pack, Truck has about 56K on it.
View 1 RepliesGetting these codes what they mean or need to do ..to get rid of them...p0022, p0171, p0174, p0183, p0340, p0300, p0316, p2006 did timing n plugs fuel filter n gas filter getting very bad gas mileage it runs good but here a ticking in motor at idle and more as u accelerate, running rough....
View 7 RepliesMy 04 F150 has started having a rough idle. While in park the engine will stall out with the A/C off. Also when in drive the truck will idle close to 1000rpm's. I had to the fuel filter cleaned and also the MAF sensor cleaned. Also did a vacuum check on it. Pulled the code and it's throwing a Lean Code. What else should I be looking for?
View 12 Replies2005 f150 5.4.
I have a slightly rough idle and can feel a miss at 1600 to 2000 RPM. Sometimes running about 65 MPH up a slight grade I can slowly press the gas pedal and the engine will begin to miss much worse, causing the truck to shake pretty bad. When it gets this bad it will slowly flash the CEL and I get a P0306 code (Cyl 6 missfire).
The truck has 148000 Miles on it and the plugs were replaced at approx 120000 by the dealer.
In the last week I have replaced the plug in cylinder 6 (looked ok) and have replaced all the COP's along with the fuel filter and the injector on #6.
I haven't been able to get it flash the CEL light or throw a code since replacing the COPs though and I am at a loss at to what to try next.
2004 F150 5.4 3v. I bought the truck with 102k on it, it now has 124k. In the morning, when the outside temp is between 30-50, the engine starts and runs fine. When I get to the first red light ( about 1 mile away) within seconds of the engine at idle, engine starts to run rough and CEL. Every time the code is p0351. If I let it sit in the driveway to full warm up... no problem. If I start the truck, shut it off and restart...no problem. It only happens at the cooler temps. I have changed plugs, used motorcraft, nickel antiseize, torqued, etc. Ford changed the coil, I have changed the coil, cleaned MAF. As soon as I cross the intersection, light stays on, rough running clears up, and runs like a champ for the rest of the day.
View 2 RepliesHave an 06 F150 5.4 3v with no power. spark knock. rough idle. wants to die while driving, and random misfire code. Have replaced fuel pump, filter, coils and plugs. What to check next? Already thought of EGR - it doesn't have one.
View 4 RepliesI just locked out the cam phasers on a 2005 f150 with a 5.4. It now idles pretty rough. If I blip the throttle the revs will rise and then drop again, and it barely catches in time to prevent a stall. If I continue to tease it this way I can usually get it to stall. I'm getting no CELs or anything, but I intermittently will get a P035x code (it seemed to rove. I've gotten cylinder 1, 4, 6, but not consistently.). I have chased those around by swapping coils, checking/cleaning the connectors, etc.
I am kind of thinking that these codes are a symptom of my idle issues, and not the actual problem. What could I have done wrong? Could it be a vac issue? I had basically the entire ECU harness and all the vac lines disconnected to do the job, but as far as I can tell everything has been reconnected to the correct locations. I did have an SCT tune done to remove the phasers in the ECU. I installed it and still have the issue, so for now I am on the stock tune just to eliminate any variables.
Could my tune be the issue? Is this how you would expect the engine to behave with locked out phasers and no corresponding ECU tune?
I have been looking for a reason for the P0012 DTC code and was looking for the VVTi Oil control valve & filter. I cannot see where it is on the engine.
View 3 Replies