Ford F-150 (2004-2008) :: 2005 - Got Codes P0022 And P0345?
Jul 20, 2015
So I have an 05 Expedition (I know this is the F-150 forum, but more visibility) that is throwing a P0022 and P0345. I get these point to the cam phasers, so before I throw $450 on a phaser kit and oil pump, I want to make sure its a good fix.
I have done a lot of research on this forum and other where people have replaced their phasers and it doesn't end up fixing the issue. So I just was looking to get some tips before I endup shot gunning parts.
View 7 Replies
Advertisement
I have a 2007 F-150 5.4L and it started throwing codes p0012 p0022 p0345 and would knock and make popping sounds after it warmed up but I could rev it up and it would go away for the most part but would come right back when I started driving it. I have since pulled down the front cover and made sure it was in time, replaced both cam phasers, replaced both vct solenoids, and replaced both cam sensors. Same issue after doing all of that. I have searched the internet and have come up with nothing.
View 3 Replies
I'm having the well known situation with P0345, P0022
Replaced both phasers, replaced cam sensor, checked timing (properly aligned), assembled back still running rough and rattling, used 10w40 oil,
Complete rebuilt engine, we did head work new seals and springs, valves are straight I had it checked out twice for assurance. New pistons, new rings, new bearings, new oil pump and seals of course. If I disconnect cam sensor Bank 2 it works fine but still runs a little rough.
- Replaced one tensioner due to gasket wear.
- I was told to check on alternator ground (it's missing I know cause it got broken and I haven't replaced that ground that goes into the engine.)
- I also was told change oil to 5w20 and filter (Not FRAM), add some lucas and it should be the fix.
- Also told to disconnect the oil pressure sensor and it would fix the problem but it will throw a code for that.
- I haven't replaced the timing chains I feel they're a little loose but they haven't jumped the teeth, so I guess they're good.
- I saw in one thread to move a teeth on phaser giving me code bank 2 (moved one teeth back and then one teeth forward but it didn't work)
When I first rebuilt the engine I was having the rough iddle then I scanned it and it gave me the cam positioning sensor code P0345, then after I replaced it problem got fixed and code was gone, I was using the truck for 2 days with no issues, then the problem cam back with the two codes P0345 and P0022!
View 13 Replies
My truck have 4 codes p0174 and p0171 system too lean bank 1 and bank 2, and p0345, p0349 camshaft position sensor bank 1 and bank 2.
View 3 Replies
I recently purchased a Ford pickup. I bought a 2004 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 200,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run good when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come to on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
View 14 Replies
I recently purchased my first Ford pickup. I bought a 2006 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 146,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run well when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around the rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
View 14 Replies
2005 f150 Lariat 4x4 5.4
Had phasers, tensioners, chains, guides, and sensors replaced. After driving the truck, it started to get a rough idle at low speeds, primarily in reverse. Changed both vct solenoids with no results. Started to get p0022 code. Changed the oil with motorcraft filter and 5w-20 twice after the work had been done, thinking it might need it. Vct's were a little varnished, but not too bad.
After a couple days of light driving, got a misfire on #3. Replaced the coil and it hasn't been back since. I am stumped at this point.
The computer show the timing to be at +13 when sitting stopped and in drive. It fluctuates a little, but not much. When the truck goes into a rough idle. The rpm's fluctuate wildly. It seems to be happening more frequently, the more I drive it.
View 3 Replies
I have been having quite a rough time fixing a P0345 code on my 06 F-150 w/5.4 w/85,000. This truck has gone to a Ford dealer every 5K for the oil change/checkup etc.
Long and short - P0345 Code @ approx 83,500 miles, rough idle once the engine was up to temp and it would clear if you bumped the skinny pedal.
I have replaced the following:
--Both Cam Phasers
--Both VCT Solenoids (they both had holes in the screens - see this post [URL] ....
--Passenger side Cam Position sensor (I broke it pulling it out to do phaser swap)
--Spark plugs - SP515's
Issue was still present so then I replaced:
--Complete Timing chain set (Chains,Gear, Guides and Tensioners) - Drivers (left) side tensioner collapsed.
Once all back together and running the code is still there so I finally installed a REAL electric oil pressure gauge. Turns out I only have about 15psi at hot idle and 50psi when driving etc.
I am at wits end, because at this point I would have to guess that the engine is junk... Either a bearing is shot or whatever... Do I take the 3-4 hours to drop the pan to potentially see what is going on? Or just drop some 15W40 in the engine and trade it in?
View 4 Replies
Getting code P0022, which is over retarded cam position, drivers side bank. My 2004 F150 has the 5.8 triton. I have replaced all cam phasers and tensioner a as well as the timing chains. I have also replaced both VCT solenoids. Before I was getting codes for both banks, now just the code mentioned above with a slight ticking as well. My question is this... What am I not seeing? What could be causing this?? Would it be beneficial t get the lockout kit for the phasers to always keep them open?? Seems to stall a little at very low RPM like when you are off-road.
View 1 Replies
I have a 2006 f150 it was making a knocking noise after the engine oil temp reached 160* and made the noise to 1700rpms. I thought it was the cam phasers so I replaced them. The truck is still making the noise and running rough and stalling but not as bad and not as often. Before it did it all of the time. The truck is timed properly. I had a new cam sensor and tried it but that did not work. I watched vct on the scan tool and both cams are in sycn.
View 2 Replies
My wife's 06 expedition 5.43v runs rough loud and dies. Not all the time just when it's to hot. I got a code it's p0022 cam sensor. I changed both started the rig up and heard loud rattling like metal maybe chain. It lasted for a the length of my video 1.4mins give or take then went fine, i turned the car off and back on everything seems fine. I know I got her oil done after driving. She had metal/plastic in her oil. I had all plugs done and actually i re did the 8th cylinder plug because it was miss firing and i pulled it by hand with only the socket no ratchet. I'm thinking the chain is going bad if not already bad. Only 113k miles my 04 f150 5.43v lasted 250k before motor swap...
View 7 Replies
Driving around today my cel flashed on. Checked my programmer its saying P0022 intake camshaft position timing-over-retarded bank 2. What is the culprit?
View 2 Replies
Where to start. Have had to replace a few COP's in the past and replaced all spark plugs 20k ago. Truck runs rough at idle and sometimes stalls when changing gear. Strong exhaust smell when sitting idle. If I put my foot in it there is hesitation. Engine seems to smooth out quite a bit but also seems like it's getting more power in stages. Codes P0426 and P0345 ....
View 2 Replies
Well I believe I finally had the opportunity to experience the wide open injector issue. I was driving to work and all of a sudden at a stop light my truck started shaking bad. It went away but as I took off every so often it would shake. I thought it was a tire or front end component so I pulled over and just got overwhelmed with the smell of gas. I drove 30 miles back home and check engine light blinked the whole way and truck ran . Also wasted at least a 1/4 tank of gas and the a/c wouldn't blow cold air either. Hooked it up to read DTC codes and got P0172, P0300, P0303, P0304, P0316 and P2196.
View 14 Replies
I have a 2005 F150 5.4 FX4 and I had these two codes thrown over the past week/few days...P0325 and P1000 (pictures below of descriptions...I have an edge programmer and have been running it on the highest setting for a while now but always run premium fuel. I got these codes and reset them and they came right back. I then reset the cpu to the factory programming and they still keep coming back. I still have premium in it and it seems like when you hammer it that it falls flat on its face! It runs good and pretty smooth but seems like it has no power when throttle is pushed hard. It seems like it has a small vibration at about 3,000 RPM but only for a few seconds and then smooths right back out again. The truck has 88,000 miles and I just put new Motorcraft plugs in it about 6,000 miles ago. Not sure what I should do or what is the next step.
Photo hosting sites ...
Image ru ...
View 5 Replies
I have an 05 F-150 Lariat 5.4 and it has been going haywire today. While driving if I hit a hard bump the power will cut off (radio, a/c) and even sometimes the truck. Check engine light came on and I pulled codes P2160 & P0506. Also, when it completely cuts off and I start it back up it says "engine in failsafe mode".
View 1 Replies
I have a 2005 F-150 5.4L 2WD 90K miles. I started getting a misfire and hard jerk when going uphill. No codes for a few days but misfire got a little worse and more jerking at full throttle acceleration or level throttle up a hill got codes p0300 and p0171. I replaced the fuel filter cleaned MAF and changed plugs Motorcraft plugs (none of them broke during replacement). Miss got worse. Missing at idle and no power 3K rmp to get to 40. Only code pulled was p0171. Replaced upstream O2 sensors and COPs. Will barely idle now. Dies when put in gear. Full throttle barely moves forward a few feet just sputters. Checked vacuum lines cannot find anything. Only code I get is P0171. Fuel injectors next? Or shop?
View 3 Replies
For 2009 and 2010 f150's with the 5.4L engine, this may apply to you.
About a month back I got some odd vibrations at start-up and while driving and the following codes:
P0345 - Camshaft Position Sensor, Bank 2 (drivers side), circulation error
P0349 - Camshaft position Sensor, Bank 2 (drivers side), circulation Interim.
These codes are common in the previous generation truck for various reasons. In my case, I started trying to troubleshoot with the easiest solutions first.
Checked the battery - fully charged.
Checked/played with the alternator connection and related wiring - looked good.
Checked the oil - it was down at the half mark on the dipstick, so toped it off with synthetic oil.
Cleared the codes, and now have been driving for a month, no issues, no codes!
If these codes come up for other folks, try the easiest on the list first, before bringing to the dealer... these codes can be really hard to solve, but sometimes we can get lucky.
View 8 Replies
05 2 wheel drive f150xl 4.2 l 135,000 miles. Smoking white out of exhaust. More at start up but doesn't go away. Turns a little blue. When parked at idle if I bring up the RPM's quick I will get a little puff of black in the white smoke. I can't smell or taste(when I touch my fingers to mouth) any anti freeze in the exhaust smoke but I live in Myrtle Beach and I have little if any anti freeze in the coolant. I flushed the motor, changed oil and filter and added a can of seafoam. I took the throttle body off and cleaned it. I also replaced the air filter because I went down a dirt road and hit a deep water hole. Dirt and mud got into the air filter and by passed it also. This was the reason for the engine flush also. I can't recall any smoke before this. Maybe a puff on start up from moisture not sure. Im going to buy a coil pack and plugs and start from there. I have never had this many codes.
P0174 Bank system 2 to lean P0300 random multipl Lean mil. Missfire detected P0305 random multiple Missfire detected cylinder 5 misfire P0306 cylinder 6 Missfire P0316 Missfire detected on start up first 1000 revolution
View 3 Replies
I took my 2009 Santa Fe Limited in to Firesteone last Friday. After the oil change and alignment, I drove out without any issues. Current mileage is 61k+.
I was running some other errands and drove about 20 miles to the next destination and parked. Came back within 45 mins and started the car when 2 lights came up on the dash - malfunction indicator lamp and engine oil pressure warning light.
I called the Firestone service center who suggested another location closer to my current position. The guy at the other location checked the error codes with the scanner which came up with P0021 and P0022.
Now, I am not very handy with anything car related and my vehicle is just out of factory warranty by 3 months and 1200 miles. I am concerned that these error codes point to expensive repairs.
Are these issues common in my model? The car seems to run fine. Could this only be the sensors or oil valves?
Assuming the worst case scenario, how long should I be able to drive before immediate need for repairs or without making the issue worse?
View 7 Replies
2 error codes? Car runs fine - nothing seems wrong - the check engine light went on, so I pulled out the scanner which came up with the 2 codes: P0021 and P0022.
View 8 Replies
