2005 F150 Lariat package with 63,000 miles. Ok... thought I had a cat crawl up in thew engine to stay warm...but alas no cat found. Got off of work and headed home, clicking/rattling noise from the front passenger side dash, then a whirring noise followed shortly there after by a dull thud (hence the cat scenario). Happened twice on the way home (~15miles) ...
View 1 RepliesI just bought a 2005 fx4 and there is a whining or whirring sound coming from the rear of the truck when I hit around 70km/h. the second i let go of the accelerator it stops.
Today when I got home after a 15 minute highway drive, i got under the truck and felt the differential area. it was warm but not hot. and there was a wet spot on it. i wiped off a drop of oil. there was also a wet spot on the bottom, seemed to be just water? I'm not sure.
The front suspension of my R has been making a lot of racket lately. Every small pavement imperfection creates a dull thud or thump. Could it be my strut mounts? They are about 3 years old — I replaced them when I installed Koni FSD under stock springs. I have a vague recollection that the distance between the top of the shock tower and the underside of the metal strut "hat" should be no more than 10mm... I have about a 12mm gap. Does that mean anything?
View 5 RepliesI have a 2004 explorer that has a clicking/rattling noise in the front of the engine. What i found is that the bottom pulley has a sleeve or ring inside of that pulley that is just floating loosely back and forth. What this is or what it is supposed to be ??? If it is a bad part, what is the best way to fix it ?
View 12 RepliesI recently installed a 2" aluminum HBS leveling kit on my F150. ('04 FX4 SCrew, 5.4, 61K miles). I was excited to finally improve the truck rather than fix something. The install was straightforward and I didnt have any issues (other than Cleveland, OH rust).
After installing the kit I noticed a whirring noise coming from the front end while driving, but I didnt think much of it and I got an alignment a couple of days later. Immediately after the alignment, the problem is still there. It sounds just like aggressive mud tires driving down the road, so I think it is coming from the tires.
The noise follows the speed of the truck (the pitch gets lower as you slow down) but you cant really start to hear it until you slow down below 45 mph. It is much more noticeable at lower speeds (probably because of the lower wind noise in the cab). I dont think it would be a CV joint/axle issue, but who knows. I am considering taking it back to have the alignment checked, but I figured I would check on here before I do.
I just bought this truck last fall, and it is one step away from being traded in because of the countless nuances this thing has (wet floors and consequently rust everywhere on the inside of the cab, rattling window trim, shaking bed, squeaky rear window, noisy phasors).
I have a 2005 Prius with 218,000 miles. Over the past month or two it's started making a horrible noise, which has finally gotten to the point that I can barely stand driving it. I used to keep my radio around 25 or so, but now need to crank it to twice that to hear anything. I can't tell what it is - it sounds vaguely like wheel bearings, but somehow different. The front bearings and a trans drain/fill was done by an independent shop 6,000 miles ago. That shop says the noise is the transmission and definitely not the bearings. My Toyota dealer says the noise is the bearings and definitely not the transmission.
Here are two videos I took this afternoon, which seem to more or less capture it, though it does sound a bit different recorded on a phone than in the cabin:
(this one has a clearer example of the noise)
Background:
I didn't have any complaints with the car until just before the 200,000 mile service was due, when I started hearing front bearing noise (I've had bearings done in about 5 vehicles, so it sounded pretty obvious to me). I brought it to the dealer and was quoted an outrageous amount for front hub assemblies (they told me they couldn't do the bearings, only the whole hub assembly), sway bar end links, alignment, transmission flush, tire rotation and the engine top end service.
I got a much better quote from my local mechanic who I've used for about 3 years, so I had him do the work. This was back in June, at 212,417. He said that they'd never done the flush on a Prius transmission before, but they had the shop manual and were sure of the procedure, and that their Valvoline rep confirmed the correct fluid, and gave them a written warranty in case of any problems. He did note that "a fair amount of metal shavings came out with the old fluid" when they did a drain and fill (not a flush). He also told me that the tires were worn unevenly so I could expect a bit of road noise after the rotation and re-alignment. They an oil change, sway bar end links, front bearings, tire rotation, alignment and reans drain and fill with Valvoline Max ATF, "Toyota Type WS fluid spec." He told me the same thing about the front hubs being complete assemblies, and the part he listed (PBR930641) appears to agree with that.
I owned a 99 f250 a little while ago. Just bought a 2006 crewcab F150 xlt about 2 months ago, and for the past month there has been this unusual grinding or whirring like noise coming from the front passenger side wheel.
I took it to the mechanic and he found a bad wheel bearing on drivers side and replaced it but that wasn't the issue. He could hear the noise but wasn't able to figure out what the actual issue was.
The noise only happens when my foot is on the throttle. (not when coasting) and i also just discovered that it doesn't make any noise at all when put in 4x4.
2005 FX4 truck. Doesn't click when going straight, but if turning wheel like turning into or out of a parking spot, it makes a clicking noise that gets faster as you get faster. It sounds almost like a baseball card in a bicycle spoke honestly. Don't know if its related, but about 3 months before i noticed the sound I had the Rancho quick lift struts installed on the truck. Somebody told me it could be wheel bearings but in my experience a wheel bearing will make a roaring noise, and it would roar while going straight down the road. This is only when turning the wheels. Also, it doesn't matter if you turn left or right, you can hear it both directions.
View 6 Replies2004 F-250 FX4 SB 5.4 V8 140k
Issue: rattling/clicking noise from passenger front wheel area at speeds lower than 15MPH, made worse under light braking and/or turns to the right.
Clicking sound is speed dependant.
Spindle? Hub? Balljoint? Sway joint? Rotor Issue?
Recently, my 04 accent (97,000 miles on engine and auto trans) has started to develop a rattling or Clanking noise coming from the engine at low RPM's. I flushed the engine and changed the oil and oil filter, thinking it could be due to oil clogging the HLA, But this was a no go. The engine is still making the noise, and I think it is starting to get worse.
The noise only happens when the car is idling at low RPM's. As soon as I rev the engine past 1000-1500 RPM's, the noise stops. The noise is worse when idling in gear, either reverse or drive, however as soon as you accelerate past 1000-1500 RPM, the noise goes away, until you decelerate to low RPM again. I'll try to take a video of it and post a link to it on here tomorrow.
Ok, so my 2007 F150 Lariat super crew cab has been at the dealership for a week now with them claiming that a part is on back order. How hard is it for them to get in a right front axle?? Granted, it was in there for other stuff too (which they can not give me a straight answer on if they fixed or not cause they are claiming the technician hasn't done the write up on it yet). My main concern is that they are screwing me around or that something happened to my truck. I am planning on stopping by there on Wed. morning after I get out of work.
Are these trucks known for bad front axles or was there some kind of a big recall on them?
Other things it went in for was the radio having the CD's cycle through when you first start up the truck, but does not happen like that all the time. Black plastic driver side front door hinge is cracked exposing the metal reinforcing part. Whirring/bearing type noise when you first start up the truck when it is cold and sits overnight (which they claim they can't hear yet waited to bring the truck inside and check it out at 3PM when they had the truck overnight from the night before when I dropped it off.) and the front driveshaft not fully disengaging when the truck is in 2wd. Almost seems like the vacuum locking hubs are still engaged.
My cat converter is rattling on driver's side and check engine light is on. Rattle is the inside of the converter, not the heat shield. How much $ and what kind of converter replacement is recommended?
View 10 Replies2008 GX with 42K and just driving home and battery light comes on and a whirring noise--pull over and open hood smell strong electrical smell--ok Alternator fried. Got it home and battery light off but still when I put a meter to my battery with engine running its only putting out 13.4V? should be at least 14.5-6 correct. Has to be Alternator cause of the symptoms and the burning electrical smell..
SO WHO has changed alternator and how hard was it? Im looking for it and I think its under the Power steering pump it seems left side engine looking at it.??
I have a 2004 ford f150 5.4l v8 triton lariat and while at idle it has a ticking noise like this video
YouTube...
However I also have a rattling noise when decelerating at around 2000 rpms that sounds like a loose chain in a box. Not sure if its VCT sensor or cam phasers ...
I have a 2007 f-150 fx4 supercab with the 5.4, it has about 37,500 miles on it. Yesterday I hooked up my trailer with no more than 800lbs of lawn mowers and as soon as I was on my way I heard a terrible rattling noise coming from the truck or the trailer. I unhooked the trailer and drove up and down the driveway and heard no noise, hooked the trailer back up and right away the rattle came back. At this point I hooked up the trailer to my dad's truck hoping it was the trailer and I drove it around the neighborhood hoping to hear the noise. No noise. So I hooked back up to my truck to drive home and the noise came right back and was even worse.
The noise was a rattling noise which I would say sounded like bb's rattling around in something, which had/has my thinking catalytic converter but no check engine light or anything has popped up. Also the noise doesn't happen unless the truck is hooked up to my little trailer with weight that I consider insignificant. So my question is could it be the catalytic converter and the the light load causes it and it will eventually occur all the time, or could it be something else that I'm not considering. I'm going to try to get it into a local mechanic but with it being the end of the month he's probably swamped with inspections. I don't want to drive it until I know what it is because I don't want to do damage to the truck.
Are there any common trim peices etc that are known to come loose and cause a rattle in our trucks? My truck has always rode fairly quiet/tight, recently with the rough roads & stiffer tires plus cold weather I have noticed alot of little rattles which are hard to narrow down sometimes. They drive me insane. So far I have noticed the rear RH suicide door was one culprit which I quietened by a couple wraps of tape around the striker, but I can hear more from possibly under the dash & rear of cab.
Also I swore that my box was coming lose, if I went over railroad tracks I could hear a hollow rattling noise that seemed to be coming from back there, I looked and all the mounts are fine & seem quite solid, but when an 05 similar to mine passed me on the street one day and I noticed his box shaking alot more than the average truck, then looked at my own in the sideview mirror and it appeared to be bouncing around more than I think it should. I am kind of OCD about rattles & squeaks and cant sleep until I shut them up
I just replaced all 4 struts on my 04 Camry. The car has 87,000 on it. I went with the Monroe OESpectrum struts and new strut mounts (Monroe). Springs looked fine, the rubber spring seats were fine as well and the bellows, so reused those items.
I now have a noise in the rear end that I did not have before. It sounds like it is coming from the lower part of the car and is not metal sounding. It is a very dull clunk when going over bumps in the road and is coming from both sides.
I replaced the sway bar bushings a couple years ago. I checked those and there is no play and appear to be fine. Also checked the sway bar links and they seem fine to me, but not sure what makes those bad. Torqued what I could. Used an electric impact wrench on the strut nuts and could not torque that because the rod spins.
I am taking it in on Monday for an alignment and to have the shop see if they can figure out the noise. Is it possible that the new parts could be binding and the alignment may take care of it? I have doubled checked my work and everything appears to be on correct.
My 2004 F-150 5.4 has a rattling noise coming from the passenger side of the engine when at operating temperature. The cam phasers and all related parts have been replaced. The reason I was prompted to change the phasers, chains, guides and tensioners was due to the engine stopping on me as I returned home from an errand. The engine had already shown signs of needing the phasers replaced.
The engine runs very smooth while warming up. Vehicle lacks power and has a rough idle after warm. Took the truck to a local mechanic, in the process of making a diagnosis, he performed a compression test. Cylinder 3 psi was much lower than the other 7 cylinders, the mechanic recommended replacing the engine (possible bent valve).
I have a Haynes manual, have searched youtube and checked this and similar forums, I have yet to find instructions on the removal of the head from the block.
(2004 Ford F-150 5.4 3v)....
I have the annoying "clicking noise" with my certified used 2008 Avalon XLS. It only occurs after the car has been sleeping overnight or after five hours or so of not the running. So this is normal according to two dealers and that I need to watch it but it isn't an issue- normal. Still, it does not leave me feeling good about it. The car has 56k miles and it is smooth, quiet and responsive, just that "ticking". It does go away after 15 minutes or so of driving. They told me why it's happening and I found some answers here, on the forum.
My question is- will it get worse? Will Toyota only address it when the "ticking" gets loud and does not go away and I'm pushing smoke from the tail pipes?
I've been reading up on the LSC 90K recall with the defective VVT-i oil line. How can I find out if my Avalon has had the oil line replaced? Just a bit confused about if any records should exist for this and where I can find out.
Original owner 2004 f150 4wd 4.6 ... Switching in and out of 4wd electronic no hubs. There is a light clicking noise when I shift out of 4wd , then when I go back to 4wd the noise stops......it seems like its not going out all the way. Is there something to lube ??I would hate to think something is grinding to hell....it sounds like a card in spokes a light purring. Bad weather heading this way.
View 2 RepliesWhen I am driving and i go to stomp on the gas my truck feels like there is no power and makes this funny clicking noise and goes no where.
NOTE : Literally just replaced plugs and coils with success. 105k miles, Oil change 2 weeks ago
2007 F150 lariat super crew 4x4, 5.4 v8 w/ 3 valve