Ford F-150 - 1997-2003 :: Vacuum Leak - Error Codes Indicating Bad O2 Sensors
Nov 29, 2014
I am having problems with a 2003 Ford F 150 with a 4.2 L V6. The problem is that it is giving me code errors that would indicate bad O2 sensors. I replaced both the upper and lower O2 sensors, and still I get the same codes. I was told by the mechanic with the computer reader that this usually means a bad vacuum seal. He suggested looking for bad hoses, but did not offer much more than that. How to proceed?
View 2 Replies
Advertisement
I'm getting the p1131 error on my 2000 xlt f150 5.4l. I know it's usually a vacuum leak on the pcv hosing, which I did have at the back and replaced as well as other softer joining sections(3 to be exact lol), but I'm still getting this error. Changed out my plugs and cops(as they needed it) and the back two plugs on both bank 1 and 2(plugs 4&8) were both white! Since this is an obvious indication of a lean burning cylinder can I make the assumption my most likely problem is dirty fuel injectors on those cylinders?
View 13 Replies
It has been since the 80's that I have attempted to do any work on a vehicle. How do I find a vacuum leak and where is my vacuum canister. I am assuming that it is a vacuum leak for anytime my engine has a load on it the air stops coming out of the dash vents and goes to the defrost vents. I have an 2000 F150 with the large engine with about 112,000 miles.
View 11 Replies
This has been on going for the past year. The blend works fine. Fan speed works correctly. The selection for ac, max ac, etc., will only allow air through defrost vents. Vacuum leak?
1998 4.6 auto super cab
View 4 Replies
I had my fuel system cleaned by the dealership last weekend and I feel like I gained 50hp+ ... Now its throwing a P0171 about a week and a half later. My computer also listed P0174 under the pending codes or whatever the section was.
2003 F150 5.4L ... I cleaned the MAF sensor a couple weeks back which stopped a rough idle and I have put some 300+ miles on it since. about 200 miles since the fuel system cleaning.
I got home and popped the hood and it sounded like a vacuum cleaner. Guess it is a vacuum leak. I might need to stop using this ford house. I swear this is the second time there was a vacuum leak(I think, first time they said it was spark gap issue). I'll be heading back in the morning now.
View 2 Replies
I've had this problem for a little while now, my 97' F150 V8 4.6L, has been running real loud and heavy. When it starts up it sounds like a race car. It finally shot me a code for P0171 - Bank 1 (passenger side) running too lean. From what I've read, this is most likely a vacuum leak but I don't know too much about it.
A couple of things I've noticed while driving it around:
1. If you are in the engine compartment while its running, you smell the excess gas on the passenger side of the truck.
2. The exhaust also smells really heavy
3. The loud and heavy running is mainly when accelerating, if I maintain a constant speed at for a little while it almost starts to run normal. Cruising down the highway its almost just as quiet as before the issue
4. Engine coolant heats up much more quickly, but doesn't get above operating temperature (read from tuner, never above 200 degrees)
In response to the problem I replaced both the O2 sensors closest to the engine and the PCV and elbow. No change. Have a fuel filter ready to install, but for some reason I don't think that is it either, as it would probably effect both bank 1 and 2.
Like I said I'm not too well versed in the vacuum system but if any of these symptoms stand out I'd love to hear your thoughts.
View 2 Replies
Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:
"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "
So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors???
I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?
View 14 Replies
This began as a troubleshooting exercise for a P0442 code (2002 model) indicating a leak in the evap emissions system. Often caused by simple things like a loose/poorly sealing filler cap. Not this time
It's a neat design, tucked away up in the fender well. Even sports a very effective stone guard (plastic shield) which hides all that tubing from view. But the shield also traps all the road salt and mud and packs it into the crevices between the tubes where it stays from one winter till the next. Even a powerful car wash probably can't dislodge the caked on mess once solidified.
View 1 Replies
So.... here's my issue. I have a 2001 supercrew 5.4 and runs great all day long, no problem starting or anything. After I have driven it for a while and turn the AC on it cools off very good then after about a 1/2hr. the truck tries to stall. It almost sounds like a vacuum leak and really bogs down. I can wait about 2hrs and then with the AC off the truck starts and drives like it should. I am steering to the IAC valve but would like to know if this is it.
View 9 Replies
Recently I have been having a strong gas smell coming from my 1997 F150 Supercab 4.6L 2wd. It is not happening all of the time. I have also been hearing what sounds like a vacuum line leak. A loud shrill which varies with the engine rpm. This also does not happen all of the time.
View 1 Replies
My wife and I received her father's 2002 F150 4.2 5 speed 2 wheel drive truck after his passing. He purchased new plug wires and wanted to replace them. So, this weekend I put in new plugs, plug wires, changed the air filter, and changed the oil and filter. Started up and ran really rough. Threw my code reader on after taking it around the block and found the following codes...
P0316 Misfire detected in first 1000 revs,
P0302 Cylinder 2 misfire,
P0305 Cylinder 5 misfire,
P0306 Cylinder 6 misfire.
New plugs were Motorcraft plugs, but had skinnier center compared to the ones that came out of truck.
Where do I start? What do I do? I am really confused as I have changed plugs and wires before and always had vehicle run better or same as before change.
View 5 Replies
So I have been having some troubles with my 2003 F150 4.6L ... Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:
"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "
So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors??? I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?
View 6 Replies
I have been having odd problems with my truck for several weeks now and what the problem may be. Occasionally the truck will not start. This happens after it has been run for an errand or to church. The truck turns over but no ignition. Sometimes if I pump the gas pedal very quickly I can get it to start. Other times I have to sit and wait about 5 minutes. I have gotten the following two error codes - P1506=Cylinder Head Temp Sensor and P1299=Idle Air Control Overspeed Error. For two days the "check engine" light was on, but now it has gone out. I have searched for an answer to this problem on these boards and one possibility may be a vacuum leak. Is this the most likely? 1998 Triton 4.6 ....
View 3 Replies
I am in the process of trying to chase down a vacuum leak on my 2003 F150 with the 5.4. I have checked all lines and cannot find it. I decided to check the long term fuel trim and noticed that my bank 1 is slightly higher than bank 2 (screenshot attached). Is this enough to assume the leak is on the bank 1 side?
View 14 Replies
I tugged on the little hose on the back pass. side of the engine,(5.4),...
and I could hear the vacuum leak that is apparently causing the erratic idle, and PO171 & PO174 to come up.
I know this hose is hooked to the Charge motion Control Valve on the back of the manifold,..I can't imagine what it does, as it terminates with some kind of plug or check valve??? Haynes say's to remove the entire manifold to get to the CMCV.
I can see it with a mirror,. I am thinking maybe long needle nose from Harbor freight,...bend the tip short,..maybe be able to change it out?????
View 14 Replies
1997 2wd, 4.0 - As you can guess it runs pretty bad at idle. It has O2 heater circuit codes for all 3 sensors. I'm leaning towards the ECM because the 2 heater wires are both hot with the key on. I unplugged the computer and turned the key on and just one wire is hot. Looks like the ecm is supposed to ground the wire to turn the heater on, but it's going hot instead?
View 14 Replies
Here are the codes I'm getting:
P0455 - large evap leak
P1451 - main control (evap canister)
P0306 - cylinder 6 misfire
P0174 - bank 2 lean
are these all related? Or two separate issues. I have replaced all the evap lines with new lines. I have a new egr valve, and exhaust manifolds, and what should I look at 1st
View 4 Replies
Just bought my volvo several days ago. It was throwing check engine codes so I had it scanned and it came down to a vacuum leak. I found the spot where it was leaking which was a little piece to the left and slightly behind the exhaust manifold, slightly behind and beneath the thermostat housing. It went from a hard plastic vacuum line, to a 1.5 inch rubber vacuum line which plugged into a nipple on the exhaust manifold or something behind the manifold. the rubber section had 3 large holes in it, so i replaced it with more rubber vacuum line. same length and same inner diameter.
What I did notice when I replaced it was that it was too large for the plastic line, slid on way too easy, but i had to fight it onto the nipple. The check engine codes went away for 2 days(I drove about 150 miles over that time) but today, the check engine light came back on, went to auto zone, had them scan it, came back with vacuum leak. So when I got home, I popped the hood, sprayed some carb cleaner by the replacement vacuum job I did, and sure enough the idle changed. What the proper replacement hose is for that area?
[URL] ....
View 1 Replies
I have a 1999 F150 with a 5.4L. I recently replaced the PCM with a new unit from autocomputerexchange.net that was programed for my truck. I installed the PCM but the truck did not start. The theft light is also flashing rapidly during cranking. I ran a code scanner a recieved the code P1260 indicating an attempted theft which disabled the truck. I read that if you have two keys you can sync the keys with the new computer but unfortunately one of the keys stopped working a couple years ago (not sure why, stopped for gas and it never started back up). Since i do not have two working keys do i have to tow the truck to a dealer and let them reprogram the keys and reset the PATS or can i have a locksmith recode the keys and sync the keys myself.
View 2 Replies
I changed both oxygen sensors yesterday on my 1997 Accord.
Check Engine Light was on and I was getting codes:
P0135 - O2 Sensor Heater Malfunction Bank 1 Sensor 1
P0141 - O2 Sensor Heater Malfunction Bank 1 Sensor 2
Also, after clearing the codes, if I started the vehicle the codes would come on instantly. So it wasn't some kind of flaky electrical issue, it was consistent.
View 1 Replies
I have a 2003 Explorer with the 4.0 K motor. It has a vacuum leak and the check engine light will come on from time to time. My work buddy has a high end computer and it showed that the driver side bank was running lean. The computer showed the O2 sensors to be working fine, and I replaced the PCV valve. All other vacuum line appear to be in good condition and I tried the spray test with the break cleaner with the motor running. This is leading me to believe the air intake gaskets where due for replacement. Here is my problem, I can not get the last bolt out of the plenum. The one on the driver side up against the fire wall. I tried to remove the cowl in order to get a straight shot at it but I can not get the seem seal to break free.
View 4 Replies
