Ford F-150 - 1997-2003 :: Turn Signals / Blinkers Started Off Blinking A Few Times Then Stopped Working
Apr 14, 2011
My blinkers started off blinking a few times then stopped working, now they don't work at all. The fuse says it goes to the brake lamps, hazards and turn signals. The hazards work as well as the brake lamps. I found the relay/flasher box and it appears the relay and flasher is the same for both the turn signals and the hazards. I checked for the wire/connector problem in the column and all looks good there. When I activate the turn signal lever I feel one click in the relay/flasher which leads me to believe the turn signal switch is working. I went ahead and replaced the relay with no results. Is the flasher internals the same for both the hazards and the turn signals or is there two independent sections inside for each?
View 4 Replies
Advertisement
I noticed that my turn signals stopped working. I replaced the flasher. Now the turn signals work but the signal indicators in the dash don't light up. Also, the hazard lights don't work either. No flashing, no blinking when I turn on my hazards. I've seen many variations while searching? 1994 B3000 2x4 extra cab.....
View 14 Replies
Well now I have to replace the multi function switch due to moving my steering wheel and the headlights sometimes working and turning signals not working. I saw a great video on youtube about changing a Multi Function Switch and it shows where the air bag needs to be removed. I was hoping that since my truck is an older 1997 F250 LD I wouldn't have to remove the airbag. Is there a way to do this w/out messing with the airbag on the 1997?
View 1 Replies
I have the keyless wireless option and one of my key fobs stopped working so I put a new battery in. So now instead of blinking once in the upper right-hand corner when I push the button and working properly instead the little red button in the corner links three times and nothing else happens . I even switched batteries from the one that still works to the one that does not work in case I got a bad new battery but no changes on either key.
View 2 Replies
Have a 1999 F-150 work truck that I bought. Of course the blinker aren't working. Flashers, wipers, H/L's all work just fine. Nothing for blinkers outside or dash indicators, either side.
Checked fuses, every time I try something and are good.
MFS. Took old one apart cleaned no change. Bought new switch no change. Have power in harness up to switch in 2 spots.
Wiring. Noticed while replacing MFS the couple wires loose on the back of harness plug. Cleaned and pushed them back into block. Making sure they are fully seated to make contact with MFS. No change. Bent contacts on switch a little for tighter connection. No change.
Replaced relay/flashers. No change. So obviously I'm overlooking something. The truck is a western truck. Hasn't been modified or messed with. Nice clean original, heck only 61000 miles. Wiring under dash looks untouched. Still has the factory AM/FM only radio.
View 8 Replies
I drive a 98 Ford Contour Sport. When I was driving today, I signaled a left turn, and the signal began working erratically. This also happened with a right turn, and, since I deliver sandwiches, happened when I turned my hazards on. Throughout the day it got worse, and eventually stopped working. I'm willing to bet that it's a wiring issue since all of my fuses are fine.
View 5 Replies
Coming back from a trip I got a e-brake light show up on the dash then noticed the signals stopped working and the heated seats no longer turn on. I scanned it with my AE and got a brake fluid sensor error come up but nothing about the signals .... is this a common problem or is there a connection between all this? 2003 F350 6.0L .....
View 2 Replies
I recently got a pretty cherry 98 Ranger 3.0 2wd extended cab auto. So far all it has needed was wiper blades, floor mats and a heater blend door. Last week my daughter informed me that the flashers and the turn signals stopped working. I looked for blown fuses and then took the low road and just bought a new flasher (my alldatadiy manual showed that the flasher was common to the turn signals and the hazard flashers so I took a shot at just throwing a part at it). That didn't fix it or else. Any pointers?
View 3 Replies
2003 F150 Super Crew 5.4
When I turn off the ignition, the drivers door lock unlocks or pushes the arm through the door for up to 30-60 seconds over and over again. I would say like 10 times and it is annoying as hell.
Is the only part in the door that controls this the actuator or is there something else that can be doing this?
View 6 Replies
So I have an 04 F250 Super Duty 6.0L and suddenly the turn signals and hazards stopped working. First I replaced the switch on the steering column...no luck. Today I replaced the flasher relay under the dash panel (the blue one)...still no luck. I remember checking fuses in the fuse box but don't remember which ones I checked but I didn't see anything obvious. I also took a quick look under the dash at all the wires for any anomalies...nothing. I'm lost... What to do next!?
View 1 Replies
I have a 1997 Ford F250. My trailer lights will work, but I have no brake lights or turn lights. I have checked all my fuses and all the fuses are good.
I was told it was probably my trailer tow relay, so I bought it at O'Reilly's, but I don't know which relay it is exactly.
I just want to know which relay number it is so I can replace it. And, if this doesn't sound right, is there something else I should be trying?
View 1 Replies
Got a 2003 F150 4.6 2wd and recently the blinkers dont work. Also some how the 4wd light came on even though the truck is a 2wd. After searching it seems alto of people recommend replacing the Multi Function Switch. The truck is plain jane no tilt wheel.
Is this the MFS everyone is talking about?
Duralast/Windshield Wiper Switch (SW1977) | 2003 Ford F150 1/2 ton P/U 2WD 8 Cylinders W 4.6L EFI |
View 14 Replies
My 99 f150 blower motor and blinkers slowly but surely went out on me. The hazards still work. I changed the flasher relay and the relay for the blower motor, and nothing. I've checked all the fuses, and checked for wire issues and nothing.
View 4 Replies
So I get to explore my first repair with this new to me car. Yesterday morning, turn signals works fine. That afternoon, the stalk apparently stopped working, which I have heard of. Interestingly though:
-the brights and cruise work
-the hazards work (my improvised indication that I'm turning )
-the stalk had been replaced once before by the PO.
Did this thing eat another stalk, or are there some other things I should check first?
View 4 Replies
I own a 1999 F350 CC SRW w/ 7.3L PSD engine. My turn signals stopped working suddenly. I've checked the fuse panel under the dash but it doesn't show any fuse for the turn signals.
My hazards do work although I noticed something very strange. When I tilt the steering column down the hazards stop working and when I tilt the column all the way up they work again. Still no turn signals though.
View 1 Replies
I used the volt meter wrong while testing my turn signal bulbs for power and not they do not work (or hazard lights).
View 3 Replies
I own a 2004 hyundai santa fe and just recently my turn signals have stopped working. My bulbs are fine because they still light up when I lock my car and my hazards work too. The flashing arrows on my dashboard wont show up for my turn signals but they will show up for hazards. I checked the fuse and its completely fine. I am so confused with what is wrong. The only thing I was doing before was messing with my new head unit which involved unplugging a lot of the stereo and fog lights and hazards but that all should have no affect on my turn signals.
View 6 Replies
The issue I am now experiencing is my passenger headlight would only turn on once in a while . The driver side headlight would work just fine both high beam light also . Today I opened my hood I verified the cable had a poor ground to the headlight I noticed a burnt smell after checking the cables . I turned on my high beams both sides turn on . Then out of no where my turn signals both (Left - right - back and front stopped working. Including the Hazard lights both front and back). The cluster would not show neither turn signals turning on ( left-right ) I noticed that my headlight turn signal on the passenger side would turn on but not blink it would stay dim only when . I pushed the hazard light button . My cluster would show the right turn signal ( no clicking no flashing arrow ). The driver side would not work either. What can I do to fix the problem? I know that I will not be able to drive the car due to the issue.
View 5 Replies
Last weekend my headlights, wipers, turn signals, AC, and horn stopped working. Through searching and another post I narrowed the issue down to my ignition switch. After taking apart my steering column and getting the switch out, I found this...
The house which is connected to the switch, with the one of the red wires obvious fried....
So I'm hoping this problem and I'm wondering who else has had this happen. When I took apart the ignition switch itself, nothing appeared to be damaged. No burns no broken pieces, etc. the metal post on the outside corresponding to the fried wire on the housing was corroded, but that was it.
I think I need to replace the housing since all that plastic melted and I chipped it away to get to the connector. I can't seem to get the connectors on the wire off of the metal connectors that are supposed to be in the housing.
View 24 Replies
I have a 00 buick lesabre that I am having problem with no turn signals. It first started with the infamous fast blinker on drivers side, so i replaced all the bulbs , so when that did not fix the problem, i thought it was the socket, but it turned out ok, so i replaced the flasher and after that, I have no blinks at all, haz work but no blinkers. i tryed old flasher but still no blinkers. i checked the fuse that runs the blinkers, it was ok. I replaced it anyway.
View 8 Replies
A few days ago my speedometer stopped working. Then yesterday all of my gauges stopped working, as well as my turn signals. If this is a fuse issue then which fuse it is?
View 9 Replies
